Contact Us
  • Home
  • COMPONENTS
  • Constant Current LED Driver ICs for Indicator and Backlight

Constant Current LED Driver ICs for Indicator and Backlight

Boost, buck and linear constant current topologies for LED strings. Output current from 10 mA on a linear regulator up to 5 A on a buck controller. PWM dimming ratios to 10,000 to 1 and analog dimming for camera-safe light. Single channel drivers and 24 channel serial sinks in one supply line.
quote now

Product Specifications

Product Overview

An LED is a current device, and a constant voltage rail will not hold its brightness. The forward voltage of one white LED moves by a few hundred millivolts from part to part and drifts with temperature, so the current through a string changes far more than the rail does. Every part on this page therefore regulates current, and the difference between them is where the excess voltage is dropped. A switching driver moves the energy into an inductor, so the loss stays small even when the input is far above the string voltage. A linear driver burns the difference as heat, which is acceptable when the headroom is a volt or two and the current is tens of milliamps, and not acceptable when a 24 V rail feeds a single 3 V LED at one amp.

The switching group starts at the TPS61165, a boost converter with a 40 V, 1.2 A switch that runs at 1.2 MHz from a 3 V to 18 V input, regulates the sense resistor to 200 mV and dims either with a PWM signal on CTRL or with a single wire EasyScale command that sets one of 32 steps. The LM3409 is the other end of the same idea: a P channel buck controller from 6 V to 42 V with a differential high side sense, constant off time control that needs no loop compensation, and a PWM dimming range quoted at 10,000 to 1, which is what a projector or a machine vision lamp needs at the bottom of its range. Where the switch has to be inside the package, the TPS92515 puts a 290 milliohm N channel FET on the die, works from 5.5 V to 65 V, holds 2 A of average current and keeps a 10,000 to 1 shunt FET dimming range, while the AL8860 covers 4.5 V to 40 V at 1.5 A with a hysteretic loop and a single pin for both on and off and brightness.

The linear and multichannel parts are chosen for different reasons. The BCR420U and BCR421U are two terminal current regulators with a preset 10 mA that a single external resistor raises to 150 mA, a 40 V rating, a 0.95 V drop and a negative temperature coefficient of 0.2 percent per kelvin, which makes a cheap indicator string self protecting without an inductor, a capacitor or a diode. The CAT4101 sinks 1 A with 500 mV of dropout on a 25 V LED pin, so a long string can be driven from a rail that is only half a volt above it. For panels and status bars, the TLC5947 gives 24 constant current sinks with 12 bit PWM on each channel, a 30 mA capability, an internal oscillator and a cascadable serial port, which removes the need for 24 separate driver loops on a front panel.

Key Specifications

ParameterSwitching driversLinear and multichannel drivers
Input range3 V to 65 V depending on part1.4 V headroom up to a 40 V rail
Output current1.2 A switch limit up to 5 A with an external FET10 mA preset up to 1 A per channel
TopologyBoost, buck, hysteretic buck, off line buck controllerLinear current sink or source
DimmingPWM to 10,000 to 1, analog to 250 to 1, one wire digitalPWM on the enable pin, 12 bit per channel
Switching frequencyUp to 1.2 MHz fixed, or set by an external resistorNot applicable, no switching node
Efficiency85 to 97 percent depending on the headroomSet by the voltage dropped across the part
ChannelsOne per packageOne per package, or 24 sinks on the TLC5947
ProtectionOpen LED clamp, cycle by cycle current limit, thermal shutdownThermal foldback and thermal shutdown

Included Models and Order Codes

The table lists the order codes most often quoted for indicator, backlight and signal lighting. State the input rail, the string voltage and current, the dimming method and the lowest brightness the application has to reach, and the part and its grade are confirmed with the packing.

Part NumberTopologyInput RangeOutput CurrentDimmingPackage
TPS61165DRVBoost, series string, 40 V switch3 V to 18 V, 38 V open LED clamp1.2 A switch, 400 mA typical stringPWM or EasyScale one wireWSON-6, 2 by 2 mm
LM3409MYBuck controller, P channel FET6 V to 42 V, 75 V on the HV suffixUp to 5 A with an external FETPWM 10,000 to 1, analog 250 to 1HVSSOP-10
TPS92515Buck with integrated N channel FET5.5 V to 42 V, 65 V on the HV suffix2 A averageShunt PWM 10,000 to 1, analog 200 to 1HVSSOP-10
AL8860MP-13Hysteretic buck, integrated switch4.5 V to 40 V1.5 A in MSOP-8EP, 1 A in TSOT25DC voltage or PWM on one pinMSOP-8EP
HV9910BOff line buck controller, external FET8 V to 450 V through the internal regulatorSet by the external FETPWM and linear, 0 to 250 mV referenceSOIC-8, SOIC-16
BCR420ULinear current regulator, NPN stageUp to 40 V10 mA preset, 150 mA with an external resistorPWM through an external transistorSC74
BCR421ULinear current regulator with enableUp to 40 V10 mA preset, 150 mA with an external resistorPWM on the enable pin to 10 kHzSC74
CAT4101TVLinear current sink, 500 mV dropout at 1 ALED pin up to 25 V1 A, set by one resistorPWM on the enable pinTO-263-5
TLC594724 channel constant current sink3.0 V to 5.5 V logic, 30 V on the LED rail30 mA per channel12 bit PWM per channel, serial portHTSSOP-32, VQFN-32

Key Features

Current set by one resistor – every part on the page derives its output current from a sense resistor or an internal reference, so the bin of the LED does not change the brightness between boards.

Dimming depth stated as a ratio – a 10,000 to 1 PWM range is the number that decides whether a lamp can be used at night, and it is quoted per part rather than left as a claim about flicker.

Open and short protection – the boost parts clamp the output when a string opens, and the buck parts limit the current cycle by cycle, so a failed LED does not take the driver with it.

Thermal foldback – the linear regulators reduce current as the die warms, at about 0.2 percent per kelvin, which keeps a small indicator part inside its package without a heat sink.

Small packages – a 2 by 2 mm WSON or a SOT-23-6 keeps the driver next to the connector, which matters when the board is a strip light or a sensor head.

Serial control for panels – the 24 channel sink takes a 12 bit word per channel over a cascadable port, so a front panel of dozens of LEDs needs three wires from the controller.

Applications

These drivers are quoted for light that carries information as well as light for illumination, typically where: A light engine is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same board, so the driver, the passives and the assembly arrive as one order.

Status and signal lighting – a tower light, a panel indicator or a machine status bar needs a fixed current per colour and a linear part removes the inductor and the switching noise from a small enclosure.

Display backlight – a boost converter drives a series string from a 5 V or 12 V rail, and the one wire dimming keeps the current continuous so the panel does not show a beat against the frame rate.

Portable instruments – a battery powered analyser or a medical handheld needs a buck driver that holds efficiency as the cell falls from 4.2 V to 3.0 V, with dimming that does not shift the colour.

Sourcing and Cross-Reference

LED drivers are a category where the part number carries the whole binning story, and where substitution is common and rarely harmless. The same family can differ in switch current, in dimming depth and in the polarity of the enable pin, and two parts that look identical on a reel can produce a different minimum brightness. We quote the full order code with the package and the temperature grade on the confirmation, and where a replacement is offered the switch current, the reference voltage and the dimming method are stated side by side so the comparison can be checked against the board.

The other practical issue is life cycle. Several linear regulators in this range are marked end of life by the supplier while the products that use them are still in production, because a two terminal current regulator is hard to replace without changing the board. For those parts we support a last time buy, hold the lot with its date code, and propose a pin compatible alternative only after the drop and the temperature coefficient have been compared.

Where the light engines are built in volume, SUPERB Assembly support covers the SMT build of the driver board.

Q: Can you supply pin to pin replacements for discontinued LED driver ICs?

A: Yes. Send the complete order code, the string voltage and current and the dimming method, and the SUPERB Tech sales team will confirm availability and the nearest part that keeps the pinout.

Why Buyers Source LED Drivers Through SUPERB

  1. Full order code on the quote: package, temperature grade and dimming variant are confirmed per line, so the part that arrives matches the board that was qualified.
  2. End of life support: parts that the supplier has stopped are quoted with the lot on hand and the date code, which keeps a running product running while an alternative is evaluated.
  3. Driver and passives together: the inductor, the sense resistor and the input capacitor for one string are quoted as a set, so the ripple and the thermal budget use the parts that will be fitted.
  4. Assembly support: where the light engine is built in volume, the SMT work on the driver board is handled by the same team that supplies the parts.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Power management ICs, LED indicators and optocouplers, Step down DC-DC converters, Obsolete part cross reference, BOM shortage recovery.