PWM Controller ICs for Switching Power Supplies
Product Specifications
Product Overview
Most switching supplies fail on three numbers rather than on topology. The under voltage lockout window decides whether the supply starts at all on the bias rail that is available, the start-up current decides how long the start-up resistor takes to charge the bulk capacitor, and the output drive decides how fast the main switch can be turned on and off at the switching frequency in use. A controller that is right for one of those can be wrong for the other two.
The families on this page cover that span. The eight pin current mode controllers handle single ended flyback, forward and boost stages up to 500 kHz with pulse by pulse current limiting, and they come in pairs that differ mainly in the lockout window and the maximum duty cycle, so the bias rail and the topology can be matched. The dual output controllers place two output transistors, two error amplifiers, a dead time comparator and an oscillator in one package for push pull, half bridge and single ended stages. The PFC controllers sit in front of the DC-DC stage and shape the input current of a universal AC input supply, either in continuous conduction mode at a fixed or programmable frequency or in transition mode with an active pull-down gate driver.
All models are grouped into this single product, so one enquiry covers the controller, its gate driver, the current sense resistors and the gate resistors for the same power stage. Tell us the topology, the input and output voltage, the switching frequency, the bias rail and the gate charge of the switch, and the controller class and the lockout window can be matched to the stage.
Key Specifications
| Parameter | Single Ended Current Mode | Dual Output Controllers | PFC Front Ends |
|---|---|---|---|
| Control mode | Peak current mode, fixed frequency | Voltage mode with dead time control, single ended or push pull | Average current mode boost PFC |
| Switching frequency | Up to 500 kHz, set by the timing resistor and capacitor | 1 kHz to 300 kHz (TL494), 100 Hz to 400 kHz (SG3525A) | Fixed 65 kHz (UCC28019A), 18 kHz to 250 kHz (UCC28180) |
| Maximum duty cycle | 100% on UC3842 and UC3843, 50% on UC3844 and UC3845 | 97% single ended, 48% per output in push pull | 98% typical (UCC28019A), 96% (UCC28180) |
| Output drive | 1 A peak totem pole, designed for N channel MOSFETs | 200 mA uncommitted transistors, plus/minus 400 mA peak on the SG3525A | 1.5 A peak gate current (UCC28019A), 600 mA source and 800 mA sink (L6562A) |
| Lockout and start-up | 16 V and 10 V on UC3842 and UC3844, 8.4 V and 7.6 V on UC3843 and UC3845, start-up current under 1 mA | Lockout with hysteresis and a soft start capacitor | Start-up under 200 uA (UCC28019A), 30 uA (L6562A) |
| Reference | Internally trimmed bandgap reference | 5 V at 5% (TL494), 5 V at 1% (TL594), 5.1 V at 1% (SG3525A) | Internal trimmed reference, 1% at 25 C (L6562A) |
| Protection | Pulse by pulse current limiting, double pulse suppression, latching operation | Latching PWM, pulse by pulse shutdown, adjustable dead time | Peak current limit, soft over current, brown-out, output over and under voltage, open loop |
| Package | PDIP-8, SOIC-8 and SOIC-14 | PDIP-16 and SOIC-16, including wide body | SOIC-8, PDIP-8 and SO-8 |
Included Models and Order Codes
The table lists the controller classes most often requested for offline and DC-DC supplies. Send the complete order code including the lockout letter, the package code and the temperature suffix and we confirm availability against that exact string.
| Model | Topology and Mode | Frequency | Drive | Package | Notes |
|---|---|---|---|---|---|
| UC3842AN | Single ended, peak current mode | Up to 500 kHz | 1 A peak totem pole | PDIP-8 | 16 V and 10 V lockout, 100% duty cycle |
| UC3842AD8 | Single ended, peak current mode | Up to 500 kHz | 1 A peak totem pole | SOIC-8 | Surface mount version for offline flyback |
| UC3843AN | Single ended, peak current mode | Up to 500 kHz | 1 A peak totem pole | PDIP-8 | 8.4 V and 7.6 V lockout for lower bias rails |
| UC3843AD8 | Single ended, peak current mode | Up to 500 kHz | 1 A peak totem pole | SOIC-8 | Start-up current under 1 mA |
| UC3844AD8 | Single ended, peak current mode | Up to 500 kHz | 1 A peak totem pole | SOIC-8 | 16 V and 10 V lockout, 50% duty cycle limit |
| UC3845AD8 | Single ended, peak current mode | Up to 500 kHz | 1 A peak totem pole | SOIC-8 | 8.4 V and 7.6 V lockout, 50% duty cycle limit |
| UC2843AD8 | Single ended, peak current mode | Up to 500 kHz | 1 A peak totem pole | SOIC-8 | -40 C to 85 C grade of the UC3843 |
| UC3846N | Push pull, current mode with symmetry correction | Up to 500 kHz | 500 mA peak totem pole | PDIP-16 | Programmable dead time, 1% bandgap reference |
| TL494CDR | Single ended or push pull, voltage mode | 1 kHz to 300 kHz | 200 mA sink or source | SOIC-16 | 5 V reference at 5%, dead time control |
| TL494CN | Single ended or push pull, voltage mode | 1 kHz to 300 kHz | 200 mA sink or source | PDIP-16 | Two error amplifiers, output control pin |
| TL594CDR | Single ended or push pull, voltage mode | 1 kHz to 300 kHz | 200 mA sink or source | SOIC-16 | 5 V reference at 1%, lockout for low VCC |
| SG3525AN | Push pull and half bridge, voltage mode | 100 Hz to 400 kHz | 400 mA peak source or sink | PDIP-16 | 5.1 V reference at 1%, soft start and dead time |
| SG3525ADWR2G | Push pull and half bridge, voltage mode | 100 Hz to 400 kHz | 400 mA peak source or sink | SOIC-16 wide body | Latching PWM, pulse by pulse shutdown |
| SG2525AN | Push pull and half bridge, voltage mode | 100 Hz to 400 kHz | 400 mA peak source or sink | PDIP-16 | Wider temperature grade for industrial supplies |
| UCC28019ADR | Boost PFC, continuous conduction mode | Fixed 65 kHz | 1.5 A peak gate current | SOIC-8 | 100 W to over 2 kW, brown-out and open loop protection |
| UCC28180D | Boost PFC, continuous conduction mode | 18 kHz to 250 kHz | Gate driver for MOSFET and IGBT | SOIC-8 | Frequency set by one resistor, burst mode at light load |
| L6562ADTR | Boost PFC, transition mode | Set by the stage | 600 mA source, 800 mA sink | SO-8 | 30 uA start-up, EN61000-3-2 supplies above 350 W |
Key Features
Current Mode Control In Eight Pins – The single ended family implements peak current mode with pulse by pulse limiting, double pulse suppression and a trimmed reference in an eight pin package, so an offline flyback needs a small external part count.
Lockout Windows To Match The Bias Rail – 16 V and 10 V versions for a high voltage start-up resistor and 8.4 V and 7.6 V versions for a low bias rail, so the supply starts on the rail that is actually available.
Fifty Percent Or Full Duty Cycle – 50% limited versions for forward and half bridge stages, and 100% versions where the transformer is reset by another means, in the same family and the same footprint.
Two Outputs For Push Pull And Half Bridge – The dual output controllers provide two transistors, two error amplifiers, a dead time comparator and a steering flip flop in one package, with the output control pin selecting single ended or push pull operation.
Adjustable Dead Time And Soft Start – The push pull family adds a dead time resistor and a soft start capacitor, and a shutdown pin that stops the outputs inside one switching period.
PFC Front Ends For Universal Input – Continuous conduction mode controllers for 100 W to over 2 kW supplies and transition mode controllers for cost sensitive stages above 350 W, both aimed at EN61000-3-2 harmonic limits.
Drive For Big Switches – Peak output currents from 400 mA to 1.5 A allow large gate charge MOSFETs and IGBTs to be switched without an external buffer stage.
Applications
Supplies where these controllers are specified: A power stage is normally quoted as one item covering the controller, its gate driver and the SUPERB PCB and SUPERB PCBA work we support for the same board.
Offline AC-DC Adapters And Chargers – Flyback and forward stages where the lockout window, the start-up current and the current limit shape decide the behaviour at power up and under fault.
Telecom And Industrial Rectifiers – Push pull and half bridge stages in DC power systems and rectifiers that need symmetrical drive and an adjustable dead time, with the secondary side driven by the same style of controller.
PFC Boost Front Ends – Universal AC input supplies in the 100 W to few kW range that have to meet harmonic limits, built around a fixed frequency continuous conduction or a transition mode controller.
DC-DC Converters And Power Modules – Boost, buck and buck boost stages in industrial equipment, including modular supplies that parallel several outputs through current mode control.
Sourcing and Cross-Reference
PWM controllers are frequently replaced by a part that is pin compatible but not equivalent. The lockout window, the maximum duty cycle, the reference tolerance and the start-up current differ between suffixes of the same family, and a supply that was designed around a 16 V lockout will not start on a 8.4 V part without the start-up network being changed. We state the suffix that is on offer and the difference it makes before the parts are ordered.
Where a controller has gone obsolete we check the current family from the same vendor first, then the wider market. Second sources that are published as pin for pin replacements are quoted with the differences that matter, including the reference accuracy, the output drive and the operating temperature range. The obsolete part replacement and shortage recovery intent pages describe the same process when a whole power board has to be re-sourced.
For volume builds, SUPERB Assembly support covers the SMT assembly of the power board.
Q: Can you supply pin to pin replacements for obsolete PWM controller part numbers?
A: Yes. Send the complete order code and the quantity and the SUPERB Tech sales team will confirm availability, the lockout suffix and the nearest pin for pin equivalent.
Why Source PWM Controllers from Superb Automation?
- Sourcing Focus: Power, analog and mixed signal parts for industrial, telecom, medical and defence builds, quoted by people who read the specification tables.
- Hard To Find And Obsolete Parts: Controller families that reach end of life while the supply stays in production, sourced with the last time buy position or the nearest equivalent stated up front.
- Cross Reference Support: Lockout window, duty cycle limit, reference accuracy, drive current and package differences listed with the quote so a substitute can be approved before production.
- Stage Level Kitting: The controller, its gate driver, the current sense resistors, the gate resistors and the feedback parts for the same stage can be quoted together.
- Stock And Build Quantities: Prototype samples, repair quantities and volume orders, with the batch information given per line.
- Reply With Evidence: Documents, batch marking and part condition are stated on the quote before the order is placed.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Power Management ICs, Gate Driver Chips for Motor and Power Stage Control, Step-Down DC-DC Converter Chips for Industrial Power Rails, LDO Linear Regulators for Low Noise Power Rails.