Contact Us
  • Home
  • COMPONENTS
  • N-Channel and P-Channel Power MOSFETs for Motor Drive and Power Conversion

N-Channel and P-Channel Power MOSFETs for Motor Drive and Power Conversion

N channel parts from 30 V to 500 V, 4 mOhm to 0.85 Ohm on resistance P channel complements from 55 V to 100 V for high side and load switching Logic level, standard and avalanche rated versions for motor drive All models on this page are grouped into one part for easy sourcing
quote now

Product Specifications

Product Overview

A power MOSFET choice is usually fixed by three numbers: the voltage the drain has to block, the current it has to carry while hot, and the on resistance the thermal design can afford. Everything else, including the package, follows from where the heat has to go. The families on this page cover the range that industrial and telecom boards actually use, from 30 V logic level parts for battery rails up to 500 V devices for off line stages.

N channel parts do the heavy switching because they offer the lowest on resistance for a given die area. P channel parts are used where a simple high side switch or a load disconnect is needed and the gate can be pulled down to ground, which removes the charge pump or bootstrap supply from the board. Boards built from both are common: N channel in the bridge, P channel in the supply path and in the reverse polarity protection.

All models are grouped into this single product, so a motor drive can be quoted as one line covering the bridge switches, the gate resistors and the drivers behind them. Give us the bus voltage, the continuous and peak current, the switching frequency and the cooling method, and the part can be checked against the thermal limit instead of being copied from an older build.

Key Specifications

ParameterN-Channel PartsP-Channel Parts
Voltage rating (VDS)30 V, 40 V, 55 V, 100 V, 200 V, 500 V-30 V, -55 V, -100 V
On resistance (RDS on)4.0 mOhm to 0.85 Ohm, at VGS 10 V20 mOhm to 0.2 Ohm, at VGS -10 V
Current rating8 A to 180 A at 25 C case-14 A to -74 A at 25 C case
Gate driveStandard gate for 10 V drive, logic level versions for 4.5 V to 5 V driveStandard gate for -10 V drive, logic level versions available
Gate chargeFrom 9 nC for small logic level parts to over 150 nC for the large dieFrom 15 nC to 120 nC
PackagesTO-220AB, D2PAK, TO-247AC, SOT-23TO-220AB, D2PAK, TO-247AC
Body diodeIntrinsic avalanche rated body diode, useful in bridge and clamp circuitsIntrinsic body diode conducting in the opposite direction
Temperature range-55 C to 175 C junction-55 C to 175 C junction

Included Models and Order Codes

The table lists the device classes held and sourced most often. Send the complete order code including the package suffix and we confirm availability, the RDS on grade and the lead form against that exact string.

ModelTypeVDSRDS onCurrentPackage
IRF3205PBFN channel55 V8.0 mOhm at 10 V110 ATO-220AB
IRF3205STRLPBFN channel55 V8.0 mOhm at 10 V110 AD2PAK, tape and reel
IRF540NPBFN channel100 V44 mOhm at 10 V33 ATO-220AB
IRF540NSTRLPBFN channel100 V44 mOhm at 10 V33 AD2PAK
IRFZ44NPBFN channel55 V17.5 mOhm at 10 V49 ATO-220AB
IRLZ44NPBFN channel, logic level55 V22 mOhm at 5 V47 ATO-220AB
IRF1404PBFN channel40 V4.0 mOhm at 10 V162 ATO-220AB
IRFB4110PBFN channel100 V4.5 mOhm at 10 V180 ATO-220AB
IRF840PBFN channel500 V0.85 Ohm at 10 V8 ATO-220AB
IRFP460PBFN channel500 V0.27 Ohm at 10 V20 ATO-247AC
IRFP250NPBFN channel200 V0.075 Ohm at 10 V30 ATO-247AC
IRF9530NPBFP channel-100 V0.2 Ohm at -10 V-14 ATO-220AB
IRF9540NPBFP channel-100 V0.117 Ohm at -10 V-23 ATO-220AB
IRF9540NSTRLPBFP channel-100 V0.117 Ohm at -10 V-23 AD2PAK
IRF4905PBFP channel-55 V20 mOhm at -10 V-74 ATO-220AB
AO3400AN channel, logic level30 V28 mOhm at 4.5 V5.7 ASOT-23

Key Features

One Family From 30 V To 500 V – Battery rails, 48 V motor stages and off line switching supplies can all be covered from the same sourcing desk instead of three separate component lists.

Logic Level Versions – Parts that reach their rated on resistance at 4.5 V gate drive, so a 3.3 V or 5 V controller can switch the stage without a gate driver on every channel.

Low On Resistance For The Current – 4 mOhm class parts for high current bridges and 0.27 Ohm to 0.85 Ohm parts for 500 V stages where switching loss dominates the loss budget.

P Channel Complements – High side switches and reverse polarity protection that need no charge pump, which keeps the component count down on instrument and handheld boards.

Avalanche Rated Body Diode – Inductive loads such as relay coils, solenoids and motor windings push the body diode into conduction, and the avalanche rating says how much energy that path can take.

Package Options For Heat – TO-220 for clip on heatsinks, TO-247AC for the high current 500 V and 200 V parts, D2PAK for surface mount boards, SOT-23 for signal level switching.

Screening And Matching – Switching sets for a bridge can be matched on RDS on and gate charge from a single batch so the phases of a three phase stage stay balanced.

Applications

Stages where these devices are specified: Bridge and switching stages are usually quoted with the SUPERB PCB and SUPERB PCBA work we support, so the switches, the gate parts and the assembly come from one source.

Motor Drive And Servo Bridges – Three phase and H bridge stages in pumps, fans, compressors and industrial servo drives running from 24 V, 48 V and 400 V class buses.

DC-DC And Power Conversion – Primary and synchronous rectifier positions in converters where the on resistance and the gate charge set the efficiency at the operating point.

Load Switching And Protection – P channel high side switches for reverse polarity protection, inrush control and load disconnect on instrument, telecom and automotive boards.

Power Supplies For RF And Telecom – Switch positions in the power section of RF amplifiers and line card supplies, where the parts have to be available as matched sets over the life of the platform.

Sourcing and Cross-Reference

Discrete power MOSFETs are copied on package and voltage more often than on anything else, and the differences that matter are hidden: on resistance at the gate voltage actually used, gate charge, avalanche rating and the thermal path through the package. We compare those figures before a substitute is proposed, and the comparison is supplied with the quote.

Throughout the IR family the original parts are still in demand long after the consumer market has moved to newer processes, and it is common for one voltage class to be in short supply while the neighbours are free. We state the lead time, whether the parts are new and sealed or pulled and tested, and which package suffixes are interchangeable on the same board.

For volume builds, SUPERB Assembly support covers the SMT assembly of the power section.

Q: Can you supply an equivalent for a discontinued or long lead time power MOSFET number?

A: Yes. Send the order code, the package suffix and the quantity and the SUPERB Tech sales team will confirm availability and the nearest equivalent with the difference stated.

Why Source Power MOSFETs from Superb Automation?

  1. Specialised Sourcing Focus: Power semiconductors, RF parts and mixed signal devices for industrial, telecom, medical and defence builds, checked against the datasheet rather than a catalogue description.
  2. Hard To Find And Obsolete Parts: Device families that outlive their datasheet status, sourced with the last time buy position or the nearest equivalent stated up front.
  3. Cross Reference Support: On resistance at the real gate voltage, gate charge, avalanche rating and package differences listed with the quote.
  4. Matched Sets: Bridge and multiphase sets can be drawn from one batch so the switching behaviour of each phase is comparable.
  5. Stock And Build Quantities: Prototype quantities, repair quantities and volume orders are all welcome, with the batch information stated per line.
  6. Reply With Evidence: Documents, batch marking and the condition of the parts are stated before the order is placed.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: BOM Shortage Recovery, Discrete and Power Semiconductors, Power Management ICs, Step-Down DC-DC Converter Chips for Industrial Power Rails.