Contact Us
  • Home
  • COMPONENTS
  • Comparator Chips for Threshold and Level Detection

Comparator Chips for Threshold and Level Detection

General purpose open collector comparators in single, dual and quad packages Micro power comparators with an internal reference for battery boards Response times from 560 ns to 60 us with adjustable hysteresis All models on this page are grouped into one part for easy sourcing
quote now

Product Specifications

Product Overview

A comparator looks like the simplest part on the schematic and causes more production problems than most of the board. The input is an analog level that moves slowly, the output feeds a digital interrupt, and the device has no internal hysteresis. The result is a burst of output transitions every time the signal crosses the threshold, which is a real fault when the output clocks a counter or triggers a controller interrupt.

The families on this page are the ones that turn up in that position. The general purpose open collector parts cover single, dual and quad channels from 2 V to 36 V with an input common-mode range that includes ground, and the open collector output can be pulled to any logic rail independent of the supply, which makes them the standard interface between an analog rail and 3.3 V logic. The micro power parts add an internal 1.182 V reference and a hysteresis pin, so a battery threshold monitor can be built without an external reference and without the oscillation that comes from a slow input.

All models are grouped into this single product, so one enquiry covers the dual and quad packages, the single channel parts with strobe and offset balance, the micro power versions with a reference and the pull-up resistors or reference dividers that go with them. Tell us the threshold voltage, the supply rails, the required response time and the temperature grade, and the family can be matched to the detection task.

Key Specifications

ParameterGeneral Purpose Open CollectorMicro Power and Reference Comparators
Supply range2 V to 36 V single supply, plus/minus 1 V to plus/minus 18 V split2.2 V to 36 V (TLV170x), 2 V to 11 V (LTC1540)
ChannelsSingle, dual and quad in one packageSingle channel, with a comparator output and a reference output
Input offset2 mV typical and 5 mV maximum at 25 C (LM393), 0.37 mV on the B grades300 uV (TLV170x), 10 mV maximum (LTC1540)
Response time1.3 us typical at 5 mV overdrive, 0.3 us on a TTL level step560 ns at 100 mV overdrive (TLV170x), 60 us at 10 mV overdrive (LTC1540)
Output typeNPN open collector, rated to 36 V, 16 mA typical sinkOpen collector or push-pull, LTC1540 sources up to 40 mA
Input common-mode rangeIncludes ground, up to VCC minus 1.5 VRail to rail inputs on the TLV170x, negative supply to V+ minus 1.3 V on the LTC1540
Quiescent current0.4 mA per package for a dual, 0.8 mA for a quad55 uA per comparator (TLV170x), 0.3 uA (LTC1540)
Reference and hysteresisExternal divider or positive feedback sets the threshold1.182 V reference with a HYST pin for adjustable hysteresis (LTC1540)
Temperature range0 C to 70 C commercial, -40 C to 125 C on the LM2903 and LM2901 grades-40 C to 125 C on the industrial versions

Included Models and Order Codes

The table lists the comparator classes most often requested for protection, level detection and interface boards. Send the complete order code including the grade letter and the package and we confirm availability against that exact string.

ModelChannelsOutputSupply RangePackageNotes
LM393DRDualOpen collector2 V to 30 VSOIC-82 mV typical offset, 1.3 us response
LM393NDualOpen collector2 V to 30 VPDIP-8Through hole version for older assemblies
LM393BIDRDualOpen collector2 V to 36 VSOIC-80.37 mV offset, 1 us response, 2 kV ESD
LM2903DRDualOpen collector2 V to 30 VSOIC-8-40 C to 125 C grade of the LM393
LM339DRQuadOpen collector2 V to 30 VSOIC-141.3 us response, common-mode input includes ground
LM339NQuadOpen collector2 V to 30 VPDIP-14Four independent comparators, one supply
LM339BIDRQuadOpen collector2 V to 36 VSOIC-141 us response, 200 uA per comparator
LM2901DRQuadOpen collector2 V to 30 VSOIC-14-40 C to 125 C grade of the LM339
LM311DSingleOpen collector or emitter5 V to 30 V, plus/minus 15 VSOIC-8Strobe input and offset balance pins, 150 nA input current
LM311PSingleOpen collector or emitter5 V to 30 V, plus/minus 15 VPDIP-8Drives loads to 50 V at 50 mA
LM211DSingleOpen collector or emitter5 V to 30 V, plus/minus 15 VSOIC-8Wider temperature grade of the LM311
TL331BIDBVRSingleOpen collector2 V to 36 VSOT-23-5Single version of the LM393B family
TLV1701AIDBVRSingleOpen collector2.2 V to 36 VSOT-23-555 uA, 560 ns, inputs include both rails
TLV1702AIDGKRDualOpen collector2.2 V to 36 VVSSOP-8Two micro power comparators for monitor boards
LTC1540CS8Single with referencePush-pull CMOS2 V to 11 VSO-80.3 uA supply, 1.182 V reference, HYST pin
LTC1540CDDSingle with referencePush-pull CMOS2 V to 11 VDFN-83 mm by 3 mm package for space limited boards
LTC1440CS8Single with referencePush-pull CMOS2 V to 11 VSO-8Pin compatible with the LTC1540, timing quoted on request

Key Features

The Family That Is Already In The BOM – The LM393, LM339 and LM2903 parts have been in production since the 1970s, so they are already qualified on most platforms and can be added to a new design without a qualification cycle.

Open Collector Outputs For Any Logic Rail – The output transistor is rated to 36 V and sinks 16 mA typical, so it can be pulled up to 1.8 V, 3.3 V or 5 V logic independently of the comparator supply, and several outputs can be tied together on one pull-up.

Single, Dual And Quad In One Order – One enquiry covers the packages used across a board set instead of one part number at a time, including the through hole versions still used in repair and retrofit work.

Micro Power Parts For Battery Boards – 55 uA per comparator on the TLV170x and 0.3 uA on the LTC1540 allow a threshold monitor to run from the cell it is watching without a regulator.

Reference And Hysteresis Inside The Package – The nanopower parts include a 1.182 V reference and a hysteresis pin, which removes the external divider that usually drifts with the supply and removes the oscillation on a slow input.

Speed Where The Detection Loop Needs It – 560 ns response on the micro power parts and 1.3 us on the general purpose family, with 0.3 us on a TTL level step, so a protection trip can be closed inside one switching period.

Strobe And Offset Balance Options – The single channel parts add a strobe input and offset balance pins, which are used for window comparators, sample gates and level detectors that have to be biased out deliberately.

Applications

Boards where these comparators are specified: Because the comparator sits between an analog rail and a logic input, it is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same board rather than on its own.

Over And Under Voltage Protection – Threshold detectors on power rails where the comparator drives a shutdown or a fault signal, including window detection built from two thresholds.

Battery Threshold Monitors – Low battery and end of discharge detection on instrument and sensor boards, using the internal reference and the hysteresis pin.

Signal Conditioning And Zero Crossing – Squaring up a sine wave, cleaning a slow sensor output or converting an analog level into a clean logic edge before a controller input.

Level Shifting Into Logic – Interfacing an analog rail to 1.8 V, 3.3 V or 5 V logic through the open collector output, which is independent of the comparator supply.

Sourcing and Cross-Reference

Comparators are still specified long after the grade that was originally used has been withdrawn. The common cases are an LM311 strobe part that is only available in a wider temperature grade, an LM339 commercial part that has to be replaced by an industrial version, and a package change from PDIP to SOIC on a board that is being re-laid out anyway. We state the grade and the package that are actually on offer rather than leaving the difference to the suffix.

Substituting one comparator for another is rarely only about the offset. Open collector and push-pull outputs are not interchangeable in a wire-AND circuit, the response time difference between an LM393 and a micro power part is two orders of magnitude, and a part with an internal reference changes the threshold network on the board. Those differences are listed with the quote, and the obsolete part replacement and shortage recovery intent pages describe the same search when the requirement covers a whole board.

SUPERB Assembly support covers the SMT build where the detection boards are assembled in volume.

Q: Can you supply drop in replacements for obsolete parts such as the LM311 or the LM339?

A: Yes. Send the order code, the grade letter and the quantity and the SUPERB Tech sales team will confirm availability and the nearest drop in option with the output type stated.

Why Source Comparator Chips from Superb Automation?

  1. Sourcing Focus: Analog and mixed signal parts for industrial, telecom, medical and defence builds, quoted by people who read the specification tables.
  2. Hard To Find And Obsolete Grades: Commercial, industrial and military grades of comparators that have been withdrawn from the catalogue, sourced with the position stated up front.
  3. Cross Reference Support: Output type, response time, reference arrangement and package differences listed with the quote so a substitute can be approved before production.
  4. Stock And Build Quantities: Prototype quantities, repair quantities and volume orders, with the batch information given per line.
  5. Passive Kitting: The pull-up resistors, the reference divider and the hysteresis resistors for the same detection circuit can be quoted together with the device.
  6. Reply With Evidence: Documents, batch marking and part condition are stated on the quote before the order is placed.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Amplifiers and Comparators, Precision Operational Amplifiers for Sensor Signal Chains, Obsolete RF Part Replacement, BOM Shortage Recovery.