DACs and Voltage References for Control Loops
Product Specifications
Product Overview
A control loop needs two things that are often bought separately but behave as one circuit: a converter that sets the demand, and a reference that decides how much that demand is worth. If the reference drifts by 10 ppm per degree, a 16 bit converter with a 5 V span has already lost most of its resolution over a 40 degree swing. That is why the parts on this page are grouped by the pair, not by the converter alone. The DACs with an internal reference carry a 2.5 V or 5 V source trimmed at test; the standalone references cover the boards where the converter has no reference of its own or where several converters must share one.
The converter range starts at the single channel AD5541A and AD5761R, moves through the dual AD5689R and the quad AD5754R and MAX5134, and ends at the octal AD5668, DAC8568, DAC80508 and the 16 channel LTC2668. The AD5754R is the part most often asked for on industrial control cards: four 16 bit channels, plus or minus 10 V output, an internal reference with 5 ppm per degree C drift and a clear pin that forces all outputs to zero when the supervisor trips. The AD5668 and DAC8568 keep eight channels in a 16 pin body for multi loop racks and laser bias cards, and the LTC2668 puts sixteen channels in a single package for ATE and optical test.
On the reference side the ADR4520 to ADR4550 family covers 2.048 V, 2.5 V, 3.0 V, 3.3 V, 4.096 V and 5.0 V with 0.02 percent initial error on the B and C grades, 2 ppm per degree C on the B grade, 1 microvolt peak to peak of low frequency noise and 8 ppm of long term drift after 4500 hours. The REF5025, REF5040 and REF5050 are the long running three terminal alternatives, and the LM4040 and TL431 shunt parts still cover the low cost end where a few milliamps of load current and 0.5 percent accuracy are enough.
Key Specifications
| Parameter | Voltage output DACs | Standalone references |
|---|---|---|
| Resolution | 12 bit and 16 bit, monotonic | Fixed output, no programming needed |
| Channel count | 1, 2, 4, 8 and 16 channels in one package | One output per package, shared by several converters |
| Output range | 0 V to 5 V unipolar, plus or minus 10 V and plus or minus 5 V bipolar, 4 to 20 mA on current output parts | 2.048 V, 2.5 V, 3.0 V, 3.3 V, 4.096 V and 5.0 V |
| Initial accuracy | Plus or minus 1 LSB INL typical on the 16 bit parts | Plus or minus 0.02 percent maximum on B and C grades |
| Drift | 5 ppm per degree C on the internal reference of the AD5754R | 2 ppm per degree C maximum on the B grade of the ADR4525 |
| Noise | Output noise set by the reference and the output amplifier | 1 microvolt peak to peak from 0.1 Hz to 10 Hz at 2.048 V |
| Settling | 5 to 10 microseconds to half an LSB on the 16 bit voltage output parts | Not applicable |
| Supply | 2.7 V to 5.5 V for the rail to rail parts, plus or minus 12 V to 15 V for bipolar output | 3 V to 15 V input, 300 mV dropout at 2 mA |
| Interface | SPI with daisy chain, I2C on the small channel count parts | None, analogue output only |
Included Models and Order Codes
The table covers the converters and references most often quoted together for control loops. State the output range, the number of channels, the interface and whether the reference is internal or shared, and the order code is confirmed with grade and packing.
| Part Number | Function | Channels | Output or Voltage | Interface | Package |
|---|---|---|---|---|---|
| AD5754RBREZ | 16 bit voltage output DAC with internal reference | 4 | 0 V to 5 V, plus or minus 5 V, plus or minus 10 V | SPI | TSSOP |
| AD5668BRUZ | 16 bit voltage output DAC | 8 | 0 V to 2.5 V or 0 V to 5 V | SPI | TSSOP |
| AD5628BRUZ | 12 bit version of the same octal family | 8 | 0 V to 2.5 V or 0 V to 5 V | SPI | TSSOP |
| DAC8568IAPW | 16 bit DAC with internal 2.5 V reference | 8 | 0 V to 2.5 V or 0 V to 5 V | SPI | TSSOP |
| DAC80508MRTET | 16 bit DAC with internal reference | 8 | 0 V to 5 V | SPI | WQFN |
| AD5689RBRUZ | 16 bit DAC with internal reference | 2 | 0 V to 2.5 V or 0 V to 5 V | SPI | TSSOP |
| AD5541ARZ | 16 bit DAC, external reference | 1 | 0 V to VREF | SPI | SOIC |
| AD5761RBRUZ | 16 bit bipolar DAC with internal reference | 1 | Plus or minus 10 V, plus or minus 5 V, 0 V to 5 V | SPI | TSSOP |
| MAX5134AGTG+ | 16 bit DAC with internal reference | 4 | 0 V to 2.5 V or 0 V to 4.096 V | SPI | TQFN |
| LTC2668IUJ-16 | 16 bit DAC with internal reference | 16 | 0 V to 5 V, plus or minus 5 V, plus or minus 10 V | SPI | QFN |
| ADR4525BRZ | Series voltage reference, 2 ppm per degree C B grade | 1 | 2.500 V | None | SOIC |
| ADR4540BRZ | Series voltage reference, 2 ppm per degree C B grade | 1 | 4.096 V | None | SOIC |
| ADR4550BRZ | Series voltage reference, 2 ppm per degree C B grade | 1 | 5.000 V | None | SOIC |
| REF5025AIDR | Series voltage reference | 1 | 2.500 V | None | SOIC |
| LM4040CIM3-2.5 | Shunt voltage reference | 1 | 2.500 V | None | SOT-23 |
| TL431AIDBZR | Adjustable shunt reference | 1 | 2.495 V to 36 V | None | SOT-23 |
Key Features
Reference and converter as one pair – the DACs with an internal reference are trimmed together at test, so the drift of the source and the gain of the output stage no longer add up in the loop error budget.
Bipolar output without an external stage – the AD5754R and AD5761R generate plus or minus 10 V from a single positive rail, which removes the negative supply and the associated sequencing from the analogue card.
Clear and reset pins – a hardware clear forces every output to zero or to a stored code when the supervisor trips, which is what a valve or laser driver needs at power down.
Channel density – eight channels in a 16 pin body and sixteen channels in one package cut the board area per loop on multi channel controllers and test racks.
Low frequency noise – 1 microvolt peak to peak from 0.1 Hz to 10 Hz on the ADR4520 series keeps the code flicker down on 16 bit loops that average slowly.
Long term stability – 8 ppm typical drift after 4500 hours means the calibration interval of an instrument can be set by the amplifier and the sensor rather than by the reference.
Applications
These parts are quoted for analogue output and calibration circuits, typically where: A loop card is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same board, so the converters, the references and the assembly come from one source.
Valve and actuator positioners – a 4 to 20 mA or plus or minus 10 V demand is generated from a 16 bit code, with the clear pin driving the output to a safe state when the loop supply drops.
Calibration and ATE racks – sixteen channels per package with a shared high accuracy reference, so channel to channel matching is set by the converter and not by the source.
Laser and optical bias control – a slow, low noise set point is held for hours, where reference drift rather than converter resolution is the limit on stability.
Sourcing and Cross-Reference
The pairing is where most orders go wrong: a BOM lists a 16 bit DAC with an external reference, and the reference line item is a different grade from the one the accuracy budget assumed. We quote the converter and the reference together, state which grade is on the line, and point out where a B grade is needed rather than letting a C grade fill the gap silently.
For long life instruments the reference is usually the part that goes obsolete first. The ADR4520 to ADR4550 family keeps the same pinout across all six output voltages, so a 2.5 V board can move to 4.096 V without a layout change, and the REF50xx parts remain available as the three terminal alternative. Where a specific grade has gone, we quote the nearest grade with the drift difference written out so the calibration interval can be judged rather than guessed.
For volume builds, SUPERB Assembly support covers the SMT assembly of the analogue output section.
Q: Can you supply the DAC and its reference as a matched pair with the grade stated on the quote?
A: Yes. Send the complete order code, the output range and the grade of the reference, and the SUPERB Tech sales team will confirm availability and whether the pair is stocked together.
Why Buyers Source Converters and References Through SUPERB
- Matched quotation: converter, reference and the output amplifier are quoted as one set with the grade of each part named, so the accuracy budget holds from the quote to the build.
- Grade discipline: A, B, C and D grades are not interchangeable in a calibration loop; the grade on the delivery note is the grade on the BOM line.
- Obsolete reference support: when a reference is discontinued we propose the nearest pin compatible voltage with the drift and noise difference stated, and hold the original part where stock allows.
- One delivery for the analogue section: converters, references, passives and protection parts for the same card ship together, which keeps the first build on one date.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Analog and mixed signal ICs, 16 bit SAR ADCs, Precision operational amplifiers, BOM shortage recovery, Pin to pin cross reference.