Crystal Units and TCXO Oscillators for Frequency References
Product Specifications
Product Overview
A frequency reference fails in ways that are hard to find later. A 32.768 kHz crystal with the wrong load capacitance runs off frequency, a MHz crystal with too high an equivalent series resistance refuses to start at low temperature, and a plain crystal used as a GNSS or LTE reference drifts far enough over temperature to lose the lock. The parameters that decide the behaviour are the same three every time: tolerance at 25 C, stability over temperature, and load capacitance plus ESR that the oscillator circuit can actually drive.
This page groups the reference parts we supply along those lines. For real time clocks and battery backed time the tuning fork parts run at 32.768 kHz with 6 pF to 12.5 pF load capacitance and ESR from 35 kohm to 90 kohm, so they can be matched to the low drive strength of an RTC pin. For the main clock of a microcontroller, an RF synthesiser or a converter the surface mount crystals cover 8 MHz to 54 MHz in the 3.2 x 2.5 mm size with typical 10 ppm tolerance and ESR of 150 ohm down to 25 ohm, depending on frequency.
Where a plain crystal is not enough, the compensated parts take over. TCXO units hold 0.5 ppm over -30 C to +85 C and 0.1 ppm over -40 C to +85 C in the network parts, from 10 MHz to 55 MHz, drawing 1.5 mA to 2 mA. MEMS oscillators cover 1 MHz to 110 MHz at 20 ppm to 50 ppm total stability in a 2.0 x 1.6 mm package with no quartz, which is the practical choice on boards that see shock and vibration. The clock generator and fanout side of a line card is covered separately on our clock generator page.
Key Specifications
| Parameter | 32.768 kHz Tuning Fork | MHz Surface Mount Crystal | TCXO |
|---|---|---|---|
| Frequency | 32.768 kHz | 8 MHz to 54 MHz fundamental | 10 MHz to 55 MHz |
| Tolerance at 25 C | plus or minus 20 ppm, plus or minus 10 ppm on selected codes | plus or minus 10 ppm or better by option | plus or minus 1 ppm to plus or minus 2 ppm |
| Stability over temperature | Tuning fork curve, software correction available | plus or minus 10 ppm to plus or minus 30 ppm | plus or minus 0.1 ppm to plus or minus 0.5 ppm |
| Load capacitance | 6 pF, 7 pF, 12.5 pF | 8 pF, 10 pF, 12 pF, or specified | 10 kohm in parallel with 10 pF internal |
| ESR | 35 kohm to 90 kohm | 150 ohm at 8 to 11 MHz down to 25 ohm above 50 MHz | Not applicable |
| Drive level | 0.5 uW to 1 uW maximum | 100 uW typical, 200 uW to 300 uW maximum | Not applicable |
| Aging first year | plus or minus 3 ppm | plus or minus 3 ppm | plus or minus 1 ppm |
| Supply and package | 2 pad SMD from 2.0 x 1.2 mm | 3.2 x 2.5 mm, 2.0 x 1.6 mm | 1.8 V, 2.8 V, 3.0 V or 3.3 V, 2.0 x 1.6 mm to 5.0 x 3.2 mm |
Included Models and Order Codes
Listed below are the reference part codes most often requested for clocks, RTC domains and radio references. Send the complete part number and the load capacitance you need and we confirm availability against that string.
| Part Number | Type | Frequency | Tolerance and Stability | Load and ESR | Notes |
|---|---|---|---|---|---|
| ABS07-32.768KHZ-T | Tuning fork SMD | 32.768 kHz | plus or minus 20 ppm at 25 C | 12.5 pF, 70 kohm maximum from -40 C to +85 C | 3.2 x 1.5 mm two pad package |
| ABS07-32.768KHZ-1-T | Tuning fork SMD | 32.768 kHz | plus or minus 10 ppm at 25 C | 12.5 pF, 70 kohm maximum | Tighter tolerance grade of the same footprint |
| ABS10-32.768KHZ-T | Tuning fork SMD | 32.768 kHz | plus or minus 20 ppm at 25 C | 70 kohm maximum | Common RTC part on microcontroller boards |
| CM315 | Tuning fork SMD | 32.768 kHz | plus or minus 20 ppm at 25 C | 12.5 pF, 70 kohm | Used with low power RTC oscillators |
| NX3215SA | Tuning fork SMD | 32.768 kHz | plus or minus 20 ppm at 25 C | 12.5 pF, 80 kohm | Higher ESR part, check the oscillator allowance |
| SC-32S | Tuning fork SMD | 32.768 kHz | plus or minus 20 ppm at 25 C | 7 pF, 70 kohm | Low load capacitance option for compact RTC pins |
| SC-32L | Tuning fork SMD | 32.768 kHz | plus or minus 20 ppm at 25 C | 7 pF, 40 kohm | Lower ESR for faster and more reliable start up |
| SC-20S | Tuning fork SMD | 32.768 kHz | plus or minus 20 ppm at 25 C | 7 pF, 70 kohm | Smaller body for wearable and module boards |
| FC-135R 32.7680KA | Tuning fork SMD | 32.768 kHz | plus or minus 20 ppm at 25 C | 50 kohm | Lower ESR than the standard 70 kohm parts |
| MC-306 32.7680K-A0 | Tuning fork SMD | 32.768 kHz | plus or minus 20 ppm at 25 C | 35 kohm | Highest drive margin in this list |
| FC-12M 32.7680KA-A3 | Tuning fork SMD | 32.768 kHz | plus or minus 20 ppm at 25 C | 90 kohm | Very small body, verify oscillator allowance before use |
| X322512MSB4SC | MHz crystal, 3.2 x 2.5 mm | 12 MHz | plus or minus 10 ppm at 25 C, plus or minus 20 ppm over temperature | 12 pF, 80 ohm maximum | Shunt capacitance 7 pF maximum, drive 100 uW typical |
| X322516MSB4SC | MHz crystal, 3.2 x 2.5 mm | 16 MHz | plus or minus 10 ppm at 25 C | 12 pF, 80 ohm maximum | Common MCU and USB clock part |
| YSX321SL 8M | MHz crystal, 3.2 x 2.5 mm | 8 MHz | plus or minus 10 ppm at 25 C | 12 pF or 20 pF, 150 ohm maximum | Frequency range of the series is 8 MHz to 64 MHz |
| YSX321SL 25M | MHz crystal, 3.2 x 2.5 mm | 25 MHz | plus or minus 10 ppm at 25 C | 12 pF or 20 pF, 50 ohm maximum | Ethernet and PHY reference option |
| SMD3225 24M | MHz crystal, 3.2 x 2.5 mm | 24 MHz | plus or minus 10 ppm at 25 C, plus or minus 10 ppm over temperature | 10 pF or specified | Shunt capacitance 3 pF, series covers 12 MHz to 54 MHz |
| TG-5035CG-13N-19.2000M3 | TCXO | 19.2 MHz | plus or minus 0.5 ppm from -30 C to +85 C, plus or minus 2 ppm at 25 C | Clipped sine output | 1.8 V to 3.3 V supply, 1.5 mA maximum, aging plus or minus 1 ppm per year |
| TG-5035CE | TCXO | 16 MHz to 40 MHz | plus or minus 0.5 ppm option, plus or minus 2 ppm range | Clipped sine output | GPS and wireless reference part in the same family |
| NT2016SA | TCXO | 12 MHz to 52 MHz | plus or minus 0.5 ppm from -30 C to +85 C | 10 kohm with 10 pF load | Supply 1.7 V to 3.3 V, up to 2 mA at 52 MHz |
| TG2016SMN | TCXO or VC-TCXO | 10 MHz to 55 MHz | plus or minus 1.5 ppm at 25 C, plus or minus 0.5 ppm over temperature | Clipped sine output, 1.7 V to 3.63 V | 2.0 x 1.6 mm, operating range -40 C to +85 C |
| TG5032CGN | TCXO for network systems | 10 MHz to 40 MHz | plus or minus 1 ppm at 25 C, plus or minus 0.1 ppm over temperature | CMOS output, 3.3 V typical | 5.0 x 3.2 mm ten pad package for line cards |
| SiT8008BI-71-33S-12.288000 | MEMS oscillator | 12.288 MHz | plus or minus 20 ppm to plus or minus 50 ppm total | 1.8 V or 2.5 V to 3.3 V | 2.0 x 1.6 mm, range 1 MHz to 110 MHz, no quartz element |
Key Features
Load capacitance matched to the circuit – the tuning fork parts are available at 6 pF, 7 pF and 12.5 pF so the load capacitors match the RTC oscillator rather than being guessed
ESR quoted, not implied – the equivalent series resistance is listed per part because it is what decides whether the oscillator starts at low temperature
TCXO down to 0.1 ppm – network grade parts hold 0.1 ppm over -40 C to +85 C for line card and base station references, and the 0.5 ppm grades cover GNSS and LTE
MEMS for shock and vibration – quartz free oscillators from 1 MHz to 110 MHz keep the clock stable on boards that see impact and continuous vibration
Frequency range covered end to end – 32.768 kHz for time keeping, 8 MHz to 54 MHz for logic and RF, 10 MHz to 55 MHz for compensated references and 1 MHz to 110 MHz for MEMS
Aging and drive level stated – first year aging and maximum drive level are given per part so the reference budget can be calculated before the board is released
Applications
The reference parts are supplied for the boards below. The clock section is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same board, so the crystal, its load capacitors and the assembly arrive as one line.
Real time clocks and time keeping – 32.768 kHz tuning fork parts with 6 pF to 12.5 pF load and matched ESR for RTC pins on low power microcontrollers and metering boards
GNSS, LTE and radio references – 0.5 ppm TCXO units from 10 MHz to 55 MHz on receivers, telemetry radios and baseband boards
Industrial and telecom timing – network grade TCXO and 0.1 ppm parts for line cards, plus MHz crystals for PHY and converter clocks
Sourcing and Cross-Reference
Crystal and oscillator supply problems show up as an exact part number with a fixed load capacitance and tolerance that cannot be swapped without changing the board. A 12.5 pF part replacing a 7 pF part, or a plus or minus 10 ppm part replacing a plus or minus 20 ppm part, is a different component even when the package looks identical.
We confirm availability against the full part number including the load capacitance and the tolerance code, and where a code is out we quote the nearest option with the ppm and load difference stated so the oscillator allowance can be rechecked before the part is fitted.
For volume builds, SUPERB Assembly support covers the SMT assembly of the timing section.
Q: Can you supply an alternative when a crystal or TCXO part number is discontinued?
A: Yes. Send the full part number, the load capacitance and the ppm code and the SUPERB Tech sales team will confirm availability and the nearest option in the same package.
Why Buy From Us
- Tolerance and load code checked: the quotation is made against the full part number including load capacitance, ppm code and package, not the series name
- ESR and drive margin confirmed: for low frequency parts we state the ESR and drive level so the oscillator can be verified before production
- Aging and stability documented: first year aging and temperature stability are given so the frequency budget over life can be calculated
- Reference parts grouped with the logic: crystals, oscillators, the controller and the load capacitors can be quoted on one line so the clock section is complete
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Crystals and Oscillators, Clock Generators and Frequency Up-Converters for Optical Line Cards, Frequency Converters and Sources, Obsolete RF Part Replacement.