GaN HEMT RF Power Transistors for Broadband Amplifiers
Product Specifications
Product Overview
A GaN on SiC HEMT puts a wide bandgap channel on a silicon carbide substrate, and the combination is why the same package can deliver 10 W at 6 GHz or 120 W at 3 GHz from a 28 V rail. The high breakdown field allows a short channel with a high drain voltage, and the substrate conducts heat better than the plastic and laminate around it, so the power density per millimetre of gate width is several times that of a silicon LDMOS part. The trade is a gate that needs a negative bias, a drain that will not survive a lost gate voltage, and a matching network that has to be built on the board.
These parts are unmatched, which means the maker publishes the die and the package and leaves the input and output matching to the amplifier. That is not a disadvantage for a broadband stage: a 10 W part matched for 2 to 6 GHz with a simple taper and a shunt capacitor covers more than an octave, and the same die is used for a 1 GHz radio and a 5 GHz link. It does mean that a replacement is never a drop in swap on performance alone, because the surrounding network was tuned against the original die.
The rails are 28 V for the CGH40000 series, 40 V for the CGHV1F025S and the CGHV1J006D, and 50 V for the CGHV27015S and the CGHV27030S. A higher rail buys output power at the same current and the same thermal resistance, so a 50 V part reaches 30 W where a 28 V part of the same size reaches 10 to 15 W. The consequence arrives at the drain choke, the decoupling and the connector, all of which have to be rated for the higher rail before the part is chosen.
Thermal figures are in the data sheet and are usually read last. The CGH40045F quotes 2.8 C per watt from junction to case, so 55 W of dissipation on a 45 W part with 55 per cent drain efficiency pushes the junction well above the case unless the case is held under 85 C. A flange part bolted to a heatsink with a thermal pad and a pill part soldered to a metal backed board reach that number in different ways, and a build that works on the bench in still air will fold back inside a sealed enclosure.
Key Specifications
Figures are typical values at 25 C case temperature from the maker data sheet, measured in the maker reference amplifier at the frequency noted. Where a value is not published for that part the cell says not quoted.
| Parameter | CGH40010F | CGH40025F | CGH40045F | CGHV27030S |
|---|---|---|---|---|
| Frequency range | DC to 6 GHz | DC to 6 GHz | DC to 4 GHz | DC to 6 GHz |
| Rated output power | 10 W | 25 W | 45 W | 30 W |
| Typical saturated power | 13 W | 30 W | 55 W | 45 dBm |
| Small signal gain | 16 dB at 2 GHz | 15 dB at 2 GHz | 16 dB at 2 GHz | 23 dB at 2.65 GHz |
| Drain efficiency at saturation | 65 per cent | 62 per cent | 55 per cent | 73 per cent at 2.65 GHz |
| Drain rail | 28 V | 28 V | 28 V | 28 V or 50 V |
| Breakdown voltage | 84 V | 84 V | 84 V | 125 V |
| Package | flange and pill | flange and pill | flange and pill | 3 x 4 mm DFN |
Included Models and Order Codes
The table covers the parts asked for by name most often, from the 6 W pill device used as a driver to the 120 W flange part used in a combiner. Die versions carry the same electrical figures without a package.
| Part Number | Frequency | Output Power | Rail | Gain | Package |
|---|---|---|---|---|---|
| CGH40006P | DC to 6 GHz | 6 W, 8 W typical | 28 V | 13 dB at 2 GHz | pill |
| CGH40010F | DC to 6 GHz | 10 W, 13 W typical | 28 V | 16 dB at 2 GHz | flange |
| CGH40025F | DC to 6 GHz | 25 W, 30 W typical | 28 V | 15 dB at 2 GHz | flange |
| CGH40045F | DC to 4 GHz | 45 W, 55 W typical | 28 V | 16 dB at 2 GHz | flange |
| CGH27015 | DC to 6 GHz | 15 W | 28 V | 15 dB | metal ceramic |
| CGH40120 | DC to 3 GHz | 120 W | 28 V | 19 dB | flange |
| CGH60030D | DC to 6 GHz | 30 W | 28 V | 15 dB | bare die |
| CGHV1F025S | DC to 15 GHz | 25 W | 40 V | 16 dB | plastic |
| CGHV1J006D | 10 MHz to 18 GHz | 6 W | 40 V | not quoted | bare die |
| CGHV27015S | DC to 6 GHz | 15 W peak, 2.5 W average | 50 V | 21 dB | 3 x 4 mm DFN |
| CGHV27030S | DC to 6 GHz | 30 W | 28 V or 50 V | 23 dB at 2.65 GHz | 3 x 4 mm DFN |
The CGHV1J006D is a die on a 0.25 micron process for 10 MHz to 18 GHz, so it is quoted for a module rather than for a connectorised amplifier. The CGHV27015S and the CGHV27030S are the two surface mount 50 V parts in the family and are used as a driver and a final stage in the same 2.4 to 2.7 GHz radio.
Key Features
Power density from a 28 V rail – 45 W of output from a flange package the size of a postage stamp, with 55 W typical at saturation and 55 per cent drain efficiency, which is what makes a 100 W amplifier a two transistor combiner instead of an eight way one.
Gain held across an octave – 16 dB at 2 GHz and 12 dB at 4 GHz on the CGH40045F, so a single stage covers a band that would need two silicon stages with a filter between them.
50 V parts for the same footprint – the CGHV27030S takes 28 V or 50 V and delivers 30 W at 2.65 GHz with 23 dB of gain, which suits a radio that already has a 50 V bus for the final stage.
Unmatched die for board level matching – the input and output are left to the amplifier, so the same transistor serves a 1 GHz radio and a 5 GHz link, and the matching network is the part that changes.
Thermal resistance quoted per package – 2.8 C per watt from junction to case on the CGH40045F, and a case temperature limit of 85 C for the published figures, which sets the heatsink rather than the electrical budget.
Ten to one output mismatch tolerance – the family is rated for a 10 to 1 load mismatch at all phase angles without damage, which covers an antenna that is disconnected while the transmitter is keyed.
Applications
These transistors are quoted for products that need watts at microwave frequency, typically where:
Radar and electronic warfare front ends – an L band or S band module needs pulsed power with a fast rise time, and the 28 V CGH40000 series is the driver and final stage in a module built on a metal backed board.
Private radio and tactical communications – a 30 W to 50 W manpack or vehicle radio at 2.4 to 2.7 GHz uses the 50 V DFN parts, where linearity under a digital modulation matters as much as saturated power.
Test instruments and broadband amplifiers – a lab amplifier specified from 1 to 6 GHz uses an unmatched 10 W or 25 W die with a tapered matching network, and the same heat sink serves several bands.
A GaN stage is only as good as the board under it, because the matching network, the drain choke and the thermal path are all on that board. That assembly is what we build as the SUPERB PCB and the SUPERB PCBA, so the transistor, the Rogers laminate and the via fence around the drain are quoted together rather than as separate line items.
Sourcing and Cross-Reference
A GaN HEMT replacement has to match four things at once: the frequency range, the saturated power at the rail in use, the small signal gain at the band centre and the thermal path of the package. A part that beats the original on power but needs a 50 V rail instead of 28 V is not a replacement, it is a new amplifier with a new supply, and that difference has to be stated before the quotation is sent.
The second point is the gate. These parts are depletion mode devices that need a negative gate voltage before the drain is applied, and a replacement with a different threshold voltage will sit at a different quiescent current on the same bias network. The bias sequence and the threshold window are part of the comparison, and the method we use for the electrical side is on RF power transistor cross reference, with the wider route for this category on defence grade components.
Supply is the third point. The CGH series has been through two ownership changes and several of the flange parts are mature rather than current, so a build with a ten year service life is quoted with a last time buy and a dated alternative. For volume builds, SUPERB Assembly support covers the die attach or the solder preform, the via fence under the drain and the matching network that surrounds the part, and the rest of the chain is listed under RF gain blocks and low noise amplifiers and RF isolators and circulators.
Q: Can you supply a drop in replacement for a CGH40010F or a CGH40025F?
A: Yes, subject to the matching network. The SUPERB Tech team checks frequency range, saturated power at 28 V, gain at the band centre and the flange footprint against the maker data sheet, and states which figures move so the network can be retuned before the first board is built.
Q: Do the parts need a negative gate supply?
A: Yes. These are depletion mode HEMTs, so a negative gate voltage has to be present before the drain is applied and has to be sequenced off after it. A part with a different threshold voltage needs the bias divider checked, which is why the threshold window is quoted with each replacement.
Q: Which part is used for pulsed radar at L band or S band?
A: The CGH40045F at 28 V is the usual 45 W choice for L band and the CGHV27030S at 50 V for S band, both with a pulse rating well above the continuous figure. Send the pulse width and the duty cycle with the enquiry, because the thermal answer changes with them.
Why Buyers Source GaN Power Transistors Through SUPERB
- Rail and frequency checked before a swap: a replacement is quoted with the rail it needs and the band it covers, because a 50 V part is not a substitute for a 28 V part on the same supply.
- Threshold window quoted with the bias: the gate voltage range is given with the part, since a different threshold changes the quiescent current on an unchanged bias network.
- Thermal path stated per package: junction to case resistance and the case limit are quoted, so the heatsink and the laminate are chosen with the transistor rather than after it fails.
- Mature flange parts held for long programmes: the CGH series is quoted with a last time buy and a dated alternative, which keeps a radar or a radio in service past the point where the part leaves the catalogue.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with RF gain blocks and low noise amplifiers, RF isolators and circulators, VCO and PLL synthesizers and the discrete and power semiconductors column.