Contact Us
  • Home
  • COMPONENTS
  • OLED and Character LCD Display Modules for Instrument Panels

OLED and Character LCD Display Modules for Instrument Panels

A display module is chosen on controller, interface and supply, because those three decide the firmware and the level shifter before the glass size is discussed. Character LCD parts on this page use the ST7066U and PIC16F690 controllers with 8 bit or 4 bit parallel buses at 5 V. Colour OLED and TFT parts run from 2.4 V to 3.6 V with SPI or parallel interfaces and need a separate display rail. Each row lists format, controller, interface and supply.
quote now

Product Specifications

Product Overview

Instrument panels keep using character LCD modules long after graphical displays became cheaper, because a 2 by 16 or 4 by 20 character module needs a parallel bus, a contrast voltage and nothing else. The controller holds the font, the cursor and the blink, so the firmware writes characters and never touches pixels. The trade is fixed content: a character module cannot show a graph, and its supply is 5 V, which the rest of a modern board no longer carries.

The ST7066U controller on the 2 by 16 module in this list takes an 8 bit or 4 bit parallel interface and drives the glass at 1/16 duty with 1/5 bias, which is the standard arrangement for a single line of characters doubled into two rows. The 4 by 20 module uses a PIC16F690 based controller instead, and the difference matters at the firmware level: the command set and the busy flag timing are not identical, so a driver written for one module is not automatically correct on the other.

Colour OLED parts take the opposite approach. The 1.27 inch module here uses an SSD1351 controller, 128 by 96 pixels and a 30 pin 0.5 mm FFC tail, with 2.5 V logic and a 12 V display rail. The high rail is generated on the module, but the current it draws and the inrush at power up still belong in the supply budget. OLED has no backlight and no viewing angle limit in the usual sense, with a contrast ratio above 10,000 to 1 and 80 degree viewing in each direction, which is why it reads well on a handheld held at an angle.

Small TFT modules such as the 2.4 inch 240 by 320 part with an ST7789S controller sit between the two. They need a 2.4 V to 3.6 V supply, a white LED backlight that draws tens of milliamps, and a parallel or serial interface that the host has to drive fast enough for the frame rate required. Luminance on that module is quoted from 252 to 448 cd per square metre depending on the backlight current, so the backlight current is a variable, not a fixed number.

The failure that costs most time on a panel build is mechanical, not electrical. An FFC tail inserted without the actuator fully open reads fine on the bench and fails after the housing is closed, and a module bonded with double sided tape that is not foam will crack at the corner screw. Both are fixed by the assembly instruction, and both are worth writing before the first article rather than after.

Key Specifications

ParameterValueApplies to
Format2 by 16 characters, 4 by 20 charactersCharacter modules
Format128 by 96 pixels, 240 by 320 pixelsColour OLED, TFT
ControllerST7066U, PIC16F690, SSD1351, ST7789SPer part number
Interface8 bit or 4 bit parallel, 3 and 4 wire SPIPer part number
Logic supply5.0 V for character modules, 2.4 to 3.6 V for TFTPer part number
Display rail2.5 V logic with 12.0 V display on the OLED moduleNHD-1.27-12896G
Contrast rail3.7 V VLCD, 1/16 duty, 1/5 biasNHD-0216K1Z-NSW-BBW-L
Display modeSTN blue negative, transmissiveCharacter modules
Luminance100 cd per square metre, 252 to 448 cd per square metreOLED, TFT
Contrast ratioAbove 10,000 to 1Colour OLED
Viewing angle80 degrees in each directionColour OLED
Operating temperature-40 to 70 C, -20 to 70 COLED, TFT
BacklightSide white LED, white LEDCharacter LCD, TFT

Included Models and Order Codes

The modules below are the formats we quote most often for instrument panels, handheld meters and control heads. Controller and interface are named for each part because the firmware depends on them, and a dash means the maker does not publish that value for the part.

Part NumberFormatControllerInterfaceSupplyNotes
NHD-1.27-12896G1.27 in colour OLED, 128 by 96SSD13513 and 4 wire SPI, 8 bit parallel2.5 V logic, 12.0 V display30 pin 0.5 mm FFC, 100 cd per square metre
NHD-0216K1Z-NSW-BBW-L2 by 16 charactersST7066U8 bit or 4 bit parallel5.0 V VDD, 3.7 V VLCDSTN blue negative, side white LED
NHD-0420D3Z-NSW-BBW-V34 by 20 charactersPIC16F690Parallel, per maker data sheetPer maker data sheetSTN blue negative, white LED backlight
NHD-2.4-240320CF-CTXI#2.4 in TFT, 240 by 320ST7789SParallel and serial, per maker data sheet2.4 to 3.6 V252 to 448 cd per square metre, -20 to 70 C
NHD-2.4-240320CF-CTXI#-F2.4 in TFT, 240 by 320ST7789SParallel and serial, per maker data sheet2.4 to 3.6 VFFC ZIF connection style
0.96 in 128 by 64 OLED module0.96 in monochrome OLED, 128 by 64SSD1306I2C3.3 to 5 VHeader module, four pin interface

Key Features

Controller named per module – The quote states the controller, so a driver written for ST7066U timing is not assumed to run on a PIC16F690 module.

Parallel or serial as needed – Character modules keep the 8 bit and 4 bit parallel bus, while OLED and TFT parts offer SPI for boards with few spare pins.

Separate display rail documented – The 12 V rail on the OLED module and the 3.7 V contrast rail on the character module are listed, because neither is generated by the host supply.

Wide viewing on OLED – 80 degrees in each direction with a contrast ratio above 10,000 to 1 makes an OLED readable at the angle a handheld is actually held.

Reflective options – STN blue negative transmissive modules with a white side LED suit a dark panel and read from the front, which is what most instrument panels need.

FFC tails with a known pitch – The OLED module uses a 30 pin 0.5 mm FFC, which matches the FPC receptacles we supply, so the tail and the connector arrive as a pair.

Applications

These modules cover the front panel of instruments, meters and handheld devices, from a two line readout to a small colour screen.

Handheld meters and analysers – A 2 by 16 character module at 5 V shows a reading and a unit with no graphics stack, and the parallel bus runs from a small microcontroller without a driver chip.

Portable instruments with a colour screen – The 1.27 inch OLED at 2.5 V logic and 12 V display fits a handheld where the screen is read at an angle and the backlight budget is tight.

Machine control heads – A 4 by 20 character module shows four lines of status on a panel that has no room for a graphical display, and its 5 V interface matches the legacy controller on the board.

Display choice sits on the same BOM as the SUPERB PCB and the SUPERB PCBA work, so the tail pitch and the connector are confirmed before the panel drawing is released.

Sourcing and Cross-Reference

Display modules are usually bought against a mechanical drawing rather than a data sheet, so the first thing we ask for is the outline, the active area and the tail position. Two modules with the same format and the same controller can differ by a millimetre in outline, and that millimetre is what decides whether the window in the panel lines up.

When a module is discontinued, the controller is the constraint. A replacement with the same controller and the same interface can often drop in with a firmware change of one timing constant, while a module with a different controller needs a new driver. We quote the controller and the interface with every alternative so the firmware impact is visible before the order.

Tails and connectors are quoted together where the customer wants it. A 30 pin 0.5 mm FFC with the matching receptacle and the right bend direction removes one of the two parts that most often arrive incompatible, and it is the pairing we check first on a panel build.

SUPERB Assembly seats the tail with the actuator open and checks the lock on every unit, which is the step that most often fails once the housing is closed.

Q: Can you supply a character LCD module that fits an existing window and uses the same controller?

A: The outline, the controller and the tail position decide it; the SUPERB Tech desk compares the drawing first and only then quotes a module with the same controller.

Why Buy Display Modules Through SUPERB

  1. Drawing first: Quotes are matched to the outline, active area and tail position, not only to the format, so the window fits on the first build.
  2. Controller stated: Every part is quoted with its controller and interface, which is what the firmware change is estimated from.
  3. Tail and connector as a pair: FFC tails are quoted with the receptacle that accepts their pitch and thickness.
  4. Legacy formats kept: Character modules at 5 V remain available for panels built around an older controller, so a service build does not need a new board.
  5. Assembly in the same house: The module and the receptacle are mounted in one build, so the tail is inserted and locked once, under inspection.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: USB Hubs and Port Controllers, Logic Level Shifters and IO Expanders, Ambient Light and Proximity Sensors, Board-to-Board and FPC Connectors.