Inductive Proximity and Photoelectric Sensors for Automation
Product Specifications
Product Overview
An inductive proximity sensor detects metal without touching it, using an oscillator whose field is damped by a conductive target. The sensing distance in the data sheet is quoted for a standard mild steel target, and it falls with any other metal: aluminium and brass give roughly half the figure, and stainless steel less than that. A machine that is built around the catalogue distance and then runs aluminium parts will see missed counts, and the fix is a shorter setting distance, not a different sensor.
The M18 part in this list is unshielded, which means its field extends past the barrel and gives 5 mm of sensing distance where a shielded part of the same size gives less. The trade is mounting: an unshielded sensor needs a clear area around the barrel, while a shielded one can be mounted flush in a metal bracket. On a machine with a metal fixture, the flush mount usually matters more than the extra millimetre.
Photoelectric sensors split into three arrangements and the names are not interchangeable. A through beam pair gives the longest range, 15 m on this family, and needs wiring at both ends. A retro reflective sensor looks at a reflector and gives 4 m with the E39-R1S reflector, with a minimum distance between sensor and reflector to avoid a false return. A diffuse sensor looks at the target itself and gives 100 mm on a white paper reference, with a narrow beam version at 90 mm plus or minus 30 mm for a small spot.
The output stage is where wiring mistakes happen. These sensors are open collector, NPN or PNP depending on the model letter, with a 100 mA load rating and light on or dark on selectable on the body. An NPN output sinks to ground and suits a controller with a sourcing input, and a PNP output sources from the supply and suits a sinking input. Connecting a PNP sensor to an NPN input reads as a stuck signal rather than as a fault.
Response time and protection class decide whether the sensor survives the machine. A 1 ms response covers most conveyor counting, while a fast packaging line needs the figure checked against the product pitch. IP67 covers washdown splash but not immersion, and the cable entry is the part that fails first, so a pre wired 2 m cable with a strain relief is usually a better choice than a connector in a wet area.
Key Specifications
| Parameter | Value | Applies to |
|---|---|---|
| Sensing distance | 5 mm plus or minus 10 percent | E2E-X5ME1 2M, M18 unshielded |
| Standard target | Iron 15 by 15 by 1 mm | E2E-X5ME1 2M |
| Setting distance | 0 to 4 mm | E2E-X5ME1 2M |
| Sensing distance | 15 m through beam, 4 m retro reflective, 100 mm diffuse | E3Z family |
| Minimum distance to reflector | 100 mm with E39-R1S | E3Z-R61 |
| Output | NPN or PNP open collector, 100 mA max | E3Z family |
| Output operation | Light on or dark on, selectable | E3Z family |
| Supply voltage | 12 to 24 VDC plus or minus 10 percent | E3Z family, E2E series |
| Current consumption | 13 mA max, 30 mA max | E2E-X5ME1, E3Z-D61 |
| Response time | 1 ms max, 2 ms max | E3Z diffuse and through beam |
| Response frequency | 0.4 kHz | E2E-X5ME1 2M |
| Differential travel | 10 percent max of sensing distance, 20 percent max of setting distance | E2E, E3Z |
| Degree of protection | IP67 | All models on this page |
| Operating temperature | -40 to 85 C, -25 to 55 C | E2E-X5ME1, E3Z family |
Included Models and Order Codes
The list gives the model numbers as they are ordered, including the cable length where it is part of the code. Output type and range are the two columns to read first, because a machine controller is wired to one of them and the range decides the bracket.
| Model Number | Type | Sensing distance | Output | Response | Connection |
|---|---|---|---|---|---|
| E2E-X5ME1 2M | Inductive, M18 unshielded | 5 mm | NPN, normally open | 0.4 kHz | 2 m pre wired cable |
| E3Z-T61 | Photoelectric through beam, emitter and receiver | 15 m | NPN, light or dark on | 1 ms | 2 m pre wired cable |
| E3Z-T81 | Photoelectric through beam, emitter and receiver | 15 m | PNP, light or dark on | 1 ms | 2 m pre wired cable |
| E3Z-R61 | Photoelectric retro reflective with reflector | 4 m with E39-R1S | NPN, light or dark on | 1 ms | 2 m pre wired cable |
| E3Z-R81 | Photoelectric retro reflective with reflector | 4 m with E39-R1S | PNP, light or dark on | 1 ms | 2 m pre wired cable |
| E3Z-D61 | Photoelectric diffuse reflective | 5 to 100 mm | NPN, light or dark on | 1 ms | 2 m pre wired cable |
| E3Z-D81 | Photoelectric diffuse reflective | 5 to 100 mm | PNP, light or dark on | 1 ms | 2 m pre wired cable |
| E3Z-L61 | Photoelectric narrow beam | 90 mm plus or minus 30 mm | NPN, light or dark on | 1 ms | 2 m pre wired cable |
Key Features
NPN and PNP in the same family – Each E3Z arrangement is available in both output types, so a machine controller is not the reason to change sensor type.
1 ms response – Through beam, retro reflective and diffuse parts respond in 1 ms, which covers counting on a conveyor at line speed.
IP67 body – A PBT housing with IP67 protection suits splash and dust, and the pre wired cable removes a connector from the wet area.
Selectable light and dark on – The operating mode is set on the body, so one stocked part covers two machine states.
Reverse polarity and short circuit protection – All models on this page carry output short circuit protection and reverse supply protection, which is what survives a wiring error at commissioning.
Standard M18 mounting – The inductive part uses the M18 barrel and thread that most brackets are already cut for, so a change of sensor does not mean a new fixture.
Applications
These parts are used where a machine counts, positions or confirms the presence of a part without contact.
Conveyor counting and end stop – A through beam pair at 15 m counts cartons across a wide belt, and the 1 ms response keeps the count accurate at line speed.
Metal part presence on fixtures – An M18 inductive sensor at 5 mm confirms that a steel workpiece is seated before the clamp closes, with 0.4 kHz response for a fast cycle.
Presence on a short range target – A diffuse sensor at 100 mm detects a plastic part with no reflector and no second unit, which suits a station where only the front of the machine is accessible.
Sensors are quoted against the SUPERB PCB and the SUPERB PCBA control board they connect to, so the input type and the cable length are checked against the harness.
Sourcing and Cross-Reference
Sensor models go obsolete faster than the machines they are fitted to, and a replacement has to match the body, the range and the output type before anything else. A 5 mm M18 part with a PNP output can be replaced by another 5 mm M18 part with a PNP output even when the maker changes, as long as the barrel length and the cable entry are the same, because the bracket and the gland are already cut.
Cable length is part of the model number and often missed on a quote. A 5 m version and a 2 m version of the same sensor are different codes, and ordering the wrong one either needs a junction box or leaves a coiled cable in a wet area. We confirm the length against the drawing before quoting.
For automation builders we quote the sensor with the connector and the bracket as one line where the machine needs them, since the parts that delay a commissioning are usually the gland, the mounting nut and the reflector rather than the sensor itself.
SUPERB Assembly builds the control board and the harness to the sensor, so the NPN or PNP output matches the input on the first power up.
Q: Can you supply the same photoelectric sensor in a PNP version when only the NPN type is on the drawing?
A: Body size, range, output type and cable length decide it; the SUPERB Tech desk reads them off the model code and confirms each one before quoting.
Why Buy Sensors Through SUPERB
- Output type named: Every quote states NPN or PNP and the operating mode, which is what the controller input is matched to.
- Cable length confirmed: The length in the model code is checked against the drawing, so a 5 m part is not supplied where 2 m was specified.
- Body and bracket matched: Barrel size and thread are quoted with the sensor, so an existing fixture can be reused.
- Accessory lines included: Reflectors, brackets and connectors are quoted with the sensor rather than left for a second order.
- Build support: The control board, the harness and the sensor are quoted as one build, so a commissioning issue is traced across all three.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Ambient Light and Proximity Sensors, Ultrasonic Transducers and Distance Sensors, Hall Effect Switches and Latches, MEMS Accelerometers.