Contact Us
  • Home
  • COMPONENTS
  • RF Coaxial Connectors and Adapters for Test and Antenna Runs

RF Coaxial Connectors and Adapters for Test and Antenna Runs

A coaxial connector is the only place on an RF board where the 50 ohm line leaves the laminate, so its VSWR and its launch geometry set the measurement floor. Micro coaxial parts such as U.FL reach 8 GHz and take a 1.13 mm cable, while SMA parts reach 18 GHz on a board or bulkhead launch. Mating cycles run from 30 on a micro part to 500 on SMA, which decides whether the connector goes on the product or on the test fixture. Each row lists frequency limit, impedance, mounting and cycles.
quote now

Product Specifications

Product Overview

Every RF measurement starts at a connector, and a poor launch adds ripple that looks like a filter problem. The three numbers that matter are the rated frequency, the VSWR at that frequency and the way the centre pin meets the trace. A micro coaxial receptacle that is rated to 8 GHz with 1.3 VSWR to 3 GHz is fine for a 2.4 GHz radio and wrong for a 6 GHz front end, even though both parts look identical on the reel.

Micro coaxial parts exist because a product needs an antenna port that is smaller than an SMA. The Hirose U.FL receptacle occupies about 7.7 square mm, weighs 15.7 mg and takes a mated height of 1.9 mm with a 0.81 mm cable, which is why it sits inside handsets and trackers. Its price is durability: the standard part is rated for 30 mates, so it belongs on the product and not on the bench fixture.

SMA remains the interface for instruments, test points and outdoor antenna runs. A board launch jack rated to 18 GHz with 500 mates and a body that stays stable from -65 C to 165 C is the part that survives being connected every day. For a board that is edge launched into a housing wall, an end launch bulkhead jack on 0.062 inch laminate is the shortest path from the trace to the outside world, and it removes a cable inside the box.

Above 8 GHz the cable becomes part of the connector. A 1.13 mm cable with a 1.6 VSWR limit to 8 GHz will not hold 18 GHz, and the solderless variants that reach 18 GHz use a different plug body and a controlled strip length. When a customer asks for 18 GHz on a U.FL footprint, the honest answer is usually a different cable assembly and a different launch, not a longer pigtail.

The mechanical side of an RF connector fails quietly. A bulkhead that is tightened without a flat washer cracks the plating at the panel, and a micro coaxial plug pulled sideways lifts the ground tabs and changes the VSWR by a few tenths without ever reading open. Torque and strain relief belong in the assembly instruction, not in the drawing notes.

Key Specifications

ParameterMicro coaxial (U.FL)SMA board and bulkhead
Characteristic impedance50 ohm50 ohm
Rated frequency0 to 8 GHz soldered, to 18 GHz solderless18 GHz
VSWR, 0 to 3 GHz1.3 max with 1.13 mm cableNot published as a single figure
VSWR, 3 to 6 GHz1.4 max with 1.13 mm cableNot published as a single figure
VSWR, 6 to 8 GHz1.6 max with 1.13 mm cableNot published as a single figure
Mated height1.9 mm to 2.4 mmStraight, end launch or bulkhead
Mating cycles30500 min
Operating temperature-40 to 105 C-65 to 165 C
Body material and finishNot published per partBrass with gold plating
InsulatorNot published per partPTFE
Centre contactNot published per partBeryllium copper, gold plated
MountingSMT receptacle, cable plugThrough hole, SMT, end launch, bulkhead

Included Models and Order Codes

The parts below are the interface types we ship most often for antenna feeds, test points and instrument front ends. Frequency and VSWR figures come from the maker data sheet for the series, and where a value depends on the cable type it is written against the cable, because the plug and the cable are quoted as one assembly above 6 GHz.

Part NumberTypeImpedanceFrequencyMountingMating cycles
U.FL-R-SMT-1(10)Micro coaxial receptacle50 ohm0 to 8 GHzSMT30
U.FL-LP-068HFMicro coaxial plug assembly, 1.13 mm cable50 ohm0 to 8 GHz, 1.6 VSWR max at 6 to 8 GHzCable30
U.FL(A)-LP-088Solderless plug assembly, 1.37 mm cable50 ohmto 18 GHzCableNot published
132134SMA PCB jack, straight50 ohm18 GHzThrough hole500
132134-10SMA PCB jack, straight50 ohm18 GHzSMT500
132289SMA end launch bulkhead jack for 0.062 inch board50 ohm18 GHzEnd launch, bulkhead500

Key Features

7.7 square mm footprint – The U.FL receptacle takes less board area than a 2.4 GHz chip antenna keep out, which is why it fits on a 20 mm tracker board.

1.9 mm mated height – A mated pair sits 1.9 mm to 2.4 mm above the board, so the antenna cable can leave under a shield can without a cutout.

Solderless variant to 18 GHz – The U.FL(A) plug uses a clamping body instead of a solder joint on the cable braid, which is what lifts the rated frequency from 8 GHz to 18 GHz.

End launch on 0.062 inch laminate – A 132289 bulkhead jack mounts on the board edge and reaches through the panel, removing one cable and one adapter from the box.

Gold over brass body – SMA jacks on this page use a brass body with gold plating and a PTFE insulator, which keeps the interface stable across the -65 C to 165 C range.

500 mate lifetime – SMA parts are rated for at least 500 matings, so they can be the test port as well as the product port.

Applications

These parts sit at the boundary between the radio and the outside world, or between the board and the instrument.

Antenna feeds on small radios – A U.FL receptacle plus a 1.13 mm pigtail carries 2.4 GHz Wi Fi, LoRa or GNSS from the board to a case mounted antenna with a 1.9 mm stack.

Instrument and lab ports – An SMA jack rated to 18 GHz and 500 matings becomes the calibration plane of a bench instrument, so the connector error is repeatable.

Outdoor and panel mounted units – A bulkhead end launch jack on the board edge removes the internal cable from a weatherproof enclosure and gives the panel a metal to metal ground.

Connector choice is one line on the SUPERB PCB and the SUPERB PCBA checklists, because the launch geometry and the solder profile are the two things that move a measured VSWR.

Sourcing and Cross-Reference

Coaxial connectors are often the last line to be filled and the first to hold up a build, because the plating and the cable assembly are made on separate schedules. When an SMA jack is quoted long, the same interface in a different body style, through hole instead of SMT or straight instead of right angle, usually ships from stock, and the electrical performance at the product frequency does not change.

For cable assemblies we quote the plug and the cable as one item, keyed to the frequency the customer actually measures at. A 1.13 mm assembly sold as an 8 GHz part and used at 6 GHz is inside its rating; the same assembly used at 12 GHz is not, and the VSWR rise shows up as a link margin loss that is easy to blame on the antenna.

Legacy interfaces stay in demand long after the maker stops promoting them. Send the part number, the panel cutout and the cable type, and we will confirm whether the original or a form and fit equivalent is available before a change is written into the drawing.

SUPERB Assembly mounts the receptacle, checks the mated height and applies the torque value on the bulkhead before the unit leaves the line.

Q: Can you supply a 50 ohm micro coaxial receptacle that is rated above 8 GHz?

A: The rated frequency, the cable and the mating cycle count decide it; the SUPERB Tech desk quotes the plug and the cable as one assembly so the rating is not lost in the pairing.

Why Buy RF Connectors Through SUPERB

  1. Interface matched to frequency: Every quote states the rated frequency and the cable it applies to, so the part is not used above its rating by accident.
  2. Connector and harness together: Pigtails are quoted with the receptacle that accepts their cable diameter, which is the pairing that most often goes wrong in a separate purchase.
  3. Test port and product port separated: We note the mating cycle rating, so a 30 mate micro part is not specified for a fixture that is connected every day.
  4. Assembly aware: The connector is fitted in the same build as the board, so torque and strain relief are applied once, in one place.
  5. Traceable lots: Each shipment carries the maker lot and the plating finish, which is what a repeat VSWR measurement depends on.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: RF Isolators and Circulators, RF Switches and PIN Diode Switches, RF Gain Blocks and Low Noise Amplifiers, Ceramic Chip Antennas.