Resistor Arrays and Precision Thin Film Resistors
Product Specifications
Product Overview
A resistor array is not four resistors in one bag. The four elements are printed on one substrate at the same time, so they track each other over temperature far better than four separate chips, and they sit in one body, so a divider that needs four matched parts takes one placement instead of four. That tracking is the reason arrays appear in difference amplifiers, attenuators and reference dividers, where the ratio matters and the absolute value does not.
A precision thin film chip is the other route to the same goal. A thin film resistor is sputtered nichrome or a similar alloy on a ceramic body, laser trimmed to a tolerance that thick film cannot reach, with a temperature coefficient of 25 ppm per degree and a shelf life that keeps the value stable. A 0.1 percent, 25 ppm part in 0603 costs a few cents and replaces a trim pot in most circuits.
The figures that decide the choice are the ratio tolerance and the tracking, not the absolute tolerance alone. Two 1 percent thick film parts from the same reel can differ by 2 percent in ratio; two elements of one array are matched by construction. Where a divider has to hold 0.1 percent over temperature, an array or a pair of thin film parts with a stated tracking figure is the answer, and the absolute tolerance is secondary.
The table below covers the codes we quote most often: 0.1 percent thin film parts in 0603 from 1 k to 100 k, a 1 percent four element array in a 1206 body, and a 5 percent four element array in an 0804 body for dense digital boards. Tolerance, temperature coefficient, power, maximum voltage and package come from the maker data sheet for each code.
Key Specifications
| Parameter | Thin film chip, 0603 | Array, 4 x 0603 in 1206 | Array, 4 x 0402 in 0804 |
|---|---|---|---|
| Tolerance | 0.1 percent | 1 percent | 5 percent |
| Temperature coefficient | 25 ppm per degree | 200 ppm per degree | 200 ppm per degree |
| Power per element | 0.1 W | 0.063 W | 0.063 W at 70 C |
| Maximum working voltage | 75 V | 50 V | not published as one figure for the family |
| Operating temperature range | -55 C to +155 C | -55 C to +155 C | -55 C to +125 C |
| Number of elements | 1 | 4, isolated | 4, isolated |
| Body size | 0603, 1.6 mm by 0.8 mm | 1206, 3.2 mm by 1.6 mm | 0804, 2.0 mm by 1.0 mm |
| Terminals | 2 | 8 | 8 |
| Construction | Sputtered thin film, laser trimmed | Thick film on one substrate | Thick film on one substrate |
| Automotive grade | AEC-Q200 on the Panasonic and Susumu parts | not qualified on the 1 percent code | AEC-Q200 |
Included Models and Order Codes
The table lists the codes we quote most often. Resistance, tolerance, temperature coefficient, power, voltage and package come from the maker data sheet for that code. The last three digits of a thin film code carry the value on the E96 grid, so 102 is 1 k, 103 is 10 k and 104 is 100 k, and the tolerance letter sits between the value and the packaging suffix.
| Part Number | Resistance | Tolerance | TCR | Power | Elements | Package |
|---|---|---|---|---|---|---|
| RG1608P-102-B-T5 | 1 k | 0.1 percent | 25 ppm per degree | 0.1 W | 1 | 0603 |
| RG1608P-103-B-T5 | 10 k | 0.1 percent | 25 ppm per degree | 0.1 W | 1 | 0603 |
| RG1608P-104-B-T5 | 100 k | 0.1 percent | 25 ppm per degree | 0.1 W | 1 | 0603 |
| ERA-3AEB102V | 1 k | 0.1 percent | 25 ppm per degree | 0.1 W | 1 | 0603 |
| ERA-3AEB103V | 10 k | 0.1 percent | 25 ppm per degree | 0.1 W | 1 | 0603 |
| ERA-3AEB104V | 100 k | 0.1 percent | 25 ppm per degree | 0.1 W | 1 | 0603 |
| YC164-FR-0710KL | 10 k per element | 1 percent | 200 ppm per degree | 0.063 W | 4, isolated | 1206 |
| EXB-28V103JX | 10 k per element | 5 percent | 200 ppm per degree | 0.063 W | 4, isolated | 0804 |
Key Features
Ratio holds where the absolute value does not – four elements on one substrate track within the array temperature coefficient, so a divider built from one array stays in ratio even when the board warms up.
0.1 percent without a trim – a laser trimmed thin film part at 0.1 percent and 25 ppm per degree replaces a trim pot and its adjustment step in most analogue circuits.
One placement instead of four – a 1206 body carries four 0603 elements, which removes three placements and three reel changes from a dense digital board.
Power quoted per element – 0.063 W per element on both arrays is a per element figure, so the total dissipation of the body is four times that, and the derating curve applies to the whole body.
Voltage limit stated with the code – 50 V on the 1 percent array and 75 V on the thin film chip are the continuous limits, and they decide whether the part can sit across a 48 V rail.
Automotive grade called out by code – the Susumu and Panasonic thin film families are AEC-Q200 qualified, and the grade is a property of the order code rather than of the series name.
Applications
These parts are quoted for boards where a ratio or a value has to hold, typically where:
Difference and instrumentation amplifiers – four matched elements set the gain of a difference stage, and the array tracking keeps the common mode rejection from drifting with temperature.
ADC and DAC reference dividers – 0.1 percent thin film parts set the divider on a converter reference, where a 1 percent part would move the full scale by more than the converter linearity error.
Attenuators and filter networks – arrays and 0.1 percent chips set the ratios in a fixed attenuator or an active filter, where the ratio error shows up directly in the flatness of the response.
The divider sits on the analogue section of the same board, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.
Sourcing and Cross-Reference
Selection starts with the error budget. If the circuit needs a ratio and the absolute value is loose, an array with a stated tracking figure is the cheap answer. If the circuit needs an absolute value within 0.1 percent over temperature, a thin film chip with a stated temperature coefficient is the answer, and the array is not a substitute.
The second check is the board. Power per element, the total body dissipation, the maximum working voltage and the pad geometry all come from the data sheet, and the array pad pattern differs between a 1206 and an 0804 body even though both hold four elements.
Where a code is short, the substitution is checked on resistance, tolerance, temperature coefficient and package, and on the value grid: 1 percent and 0.1 percent parts live on the E96 grid, 5 percent parts on E24, so a value that exists in one grid may not exist in the other. The route for these checks is on our obsolete part cross reference hub, and the drop in comparison is on pin to pin cross reference.
For volume builds, SUPERB Assembly support covers the array orientation, the Kelvin connections on current sense paths and the reel change that a single array body removes.
Q: Can you supply 0.1 percent thin film resistors with the temperature coefficient stated, and matched arrays for the same divider?
A: Yes. Send the resistance, the tolerance, the temperature coefficient, the quantity and the package, and the SUPERB Tech team will confirm the value on the E96 grid, the power per element and the qualification from the maker data sheet before quoting.
Why Buyers Source Precision Resistors Through SUPERB
- Tolerance and TCR quoted together: 0.1 percent without the temperature coefficient is half a specification, so both are given with the code.
- Value grid checked: E96 and E24 values are not interchangeable, and the grid is confirmed before a substitute is offered.
- Arrays quoted by element count: power per element, total body dissipation and pad pattern are stated, which is what a placement file needs.
- Qualification read from the code: AEC-Q200 grade is a property of the order code, so it is confirmed on the code rather than on the series name.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Passive components, Current sense shunt resistors, MLCC and ceramic capacitors, DACs and voltage references, Precision operational amplifiers, Pin to pin cross reference.