Contact Us
  • Home
  • COMPONENTS
  • GNSS Receiver Modules for Positioning and Timing

GNSS Receiver Modules for Positioning and Timing

A GNSS module puts the receiver, the compensated clock, the filters and the antenna feed in one screened can that is already characterised. Tracking sensitivity from -165 dBm to -167 dBm decides whether a tracker keeps a fix inside a vehicle or under dense canopy. Concurrent reception of four constellations raises the visible satellite count in street canyons where one system drops below four satellites. Timing parts are quoted on 1PPS accuracy, which is 30 ns RMS on the M9 and M10 engines. Every row lists supply range, host interface and footprint, because those three decide the carrier board.
quote now

Product Specifications

Product Overview

A GNSS receiver module is the part of a positioning product that is hardest to build from scratch. The radio has to resolve a signal that arrives at about -130 dBm, which is below the thermal noise floor of a wideband receiver, and it has to do that while a cellular transmitter on the same board is sending bursts. Putting the receiver, the low noise amplifier, the surface acoustic wave filter, the compensated crystal and the antenna feed on one screened module moves that work to the module maker, and leaves the product team with a supply rail, a serial port and an antenna.

The first number to read is tracking sensitivity. The u-blox M8 engine in the NEO-M8N reaches -167 dBm, the M9 engine in the NEO-M9N reaches the same figure with four constellations running at once, and the Quectel L86 reaches -165 dBm on GPS and GLONASS. A decade ago a receiver needed a clear view of the sky to start at all; these parts hold a fix in a parked vehicle under a metal roof, which is the condition an asset tracker actually meets.

The second number is how many constellations run at the same time. A single system receiver needs four satellites above the horizon and a good geometric spread, and inside a street canyon half of them are blocked. Concurrent GPS, GLONASS, BeiDou and Galileo reception gives the engine two to three times the candidate set, so it keeps a fix with a worse sky view. The price is current: four constellations cost more milliamps than one, and the module data sheet quotes each mode separately for that reason.

Time to first fix depends more on the backup rail than on the receiver. A cold start on the M8 engine takes about 26 seconds, a warm start about 3 seconds and a hot start about 1 second, and the difference is whether the ephemeris in backup memory survived. That is why every carrier board needs a backup supply on the backup pin, either a small cell or a supercapacitor, and why the current on that pin, which is a few microamps, is worth checking before the cell is chosen.

The antenna is where most field failures come from. A ceramic patch needs a ground plane of at least 50 mm by 50 mm to radiate as specified, and a patch mounted on a 20 mm board loses several dB, which shows up as a longer cold start rather than as a dead receiver. An active antenna moves the amplifier into the antenna housing and needs a bias tee and a short circuit protected feed on the module side. The L86 module carries both the patch and the low noise amplifier, and it reports antenna open and short conditions over NMEA, which turns a field return into a log entry.

Timing products read a different set of figures. A telecom line card or a small cell uses the 1PPS output as a frequency and phase reference, and the accuracy of that pulse is 30 ns RMS on the M9 and M10 engines, with a pulse rate that is programmable from 0.25 Hz to 10 MHz. The module still needs a holdover story, because 1PPS accuracy without satellites falls back to whatever oscillator the board provides, and that is why a timing card usually pairs a GNSS module with a TCXO or an OCXO rather than relying on the module clock alone.

The tables below list the parts we quote most often. Sensitivity, supply, interface and footprint come from the maker data sheet for each order code, and no figure is carried across from a neighbouring family.

Key Specifications

ParameterNEO-M8N-0NEO-M9N-00BMAX-M10SL86LC86G
Receiver engine72 channel u-blox M892 channel u-blox M9u-blox M10MediaTek engineMediaTek engine
ConstellationsGPS, GLONASS, BeiDou, GalileoGPS, GLONASS, BeiDou, Galileo, QZSS, SBASGPS, GLONASS, BeiDou, GalileoGPS, GLONASS, QZSS, SBASGPS, GLONASS, BeiDou, Galileo, QZSS
Tracking sensitivity-167 dBm-167 dBm-167 dBm-165 dBm-166 dBm
Cold start sensitivity-148 dBm-148 dBm-148 dBm-148 dBm-148 dBm
Horizontal accuracy2.5 m CEP1.5 m CEP with SBAS1.5 m CEP with SBAS2.5 m CEP2.0 m CEP
Navigation update rateUp to 10 HzUp to 25 Hz with four constellationsUp to 10 HzUp to 10 Hz, 1 Hz defaultUp to 10 Hz
Supply voltage1.65 V to 3.6 V2.7 V to 3.6 V1.76 V to 3.6 V3.0 V to 4.3 V, 3.3 V typical3.0 V to 4.3 V
Time pulse accuracyNot specified on this engine30 ns RMS, 99 percent30 ns RMS, 99 percent15 ns typical, time service not supported30 ns RMS
Host interfaceUART, SPI, I2C, USBUART, SPI, I2CUART, I2C, SPIUART, 4800 to 115200 bpsUART, I2C
AntennaExternal, active or passiveExternal, active or passiveExternal, active or passiveOn module patch 18.4 x 18.4 x 4.0 mm plus LNAOn module patch antenna plus LNA

Included Models and Order Codes

The order codes below are the ones we hold or source most often. Footprint is the module body in millimetres, not the keep out area, which is larger on every part because of the antenna feed and the ground plane requirement. Where a figure is not published for that exact code the cell is left empty rather than copied from a sister part.

Part NumberConstellationsTracking sensitivitySupplyInterfaceFootprint
NEO-M8N-0GPS, GLONASS, BeiDou, Galileo-167 dBm1.65 V to 3.6 VUART, SPI, I2C, USB12.2 x 16.0 mm LCC, 24 pad
NEO-M8Q-0GPS, GLONASS, BeiDou-167 dBm1.65 V to 3.6 VUART, SPI, I2C, USB12.2 x 16.0 mm LCC
NEO-M9N-00BGPS, GLONASS, BeiDou, Galileo, QZSS-167 dBm2.7 V to 3.6 VUART, SPI, I2C12.2 x 16.0 mm LCC
MAX-M10SGPS, GLONASS, BeiDou, Galileo-167 dBm1.76 V to 3.6 VUART, I2C, SPI10.1 x 9.7 mm LCC
L76-LGPS, GLONASS, BeiDou, Galileo, QZSS-167 dBm2.8 V to 4.3 VUART, I2C10.1 x 9.7 mm LCC
LC76GGPS, GLONASS, BeiDou, Galileo, QZSS-166 dBm2.8 V to 4.3 VUART, I2C10.1 x 9.7 mm
L86GPS, GLONASS, QZSS, SBAS-165 dBm3.0 V to 4.3 V, 3.3 V typicalUART18.4 x 18.4 x 4.0 mm with patch
LC86GGPS, GLONASS, BeiDou, Galileo, QZSS-166 dBm3.0 V to 4.3 VUART16.0 x 16.0 mm with patch

Key Features

Four constellations at once – concurrent GPS, GLONASS, BeiDou and Galileo reception raises the candidate satellite count, which is what keeps a fix in a street canyon or under a vehicle roof.

Sensitivity stated for tracking, not only for cold start – the -165 dBm to -167 dBm figure is the level at which the engine still tracks, and it decides whether a tracker recovers after a tunnel.

Backup rail keeps the ephemeris – hot start in about 1 second depends on the backup pin staying powered, and that pin draws only a few microamps, so a supercapacitor is often enough.

1PPS output for timing cards – the M9 and M10 engines specify 30 ns RMS on the time pulse, and the pulse rate is programmable from 0.25 Hz to 10 MHz for a line card or a small cell.

Antenna diagnostics on the module – the L86 reports antenna open, short and external antenna presence over NMEA, so a field unit logs the fault instead of returning it as no fix.

Patch antenna integrated where space allows – the L86 and LC86G carry the patch and the low noise amplifier on the module, which removes the feed loss and the matching network from the carrier board.

One footprint across several engines – the 10.1 x 9.7 mm LCC footprint is shared by the MAX-M10S, L76-L and LC76G, so a board can move between engines without a new layout.

Applications

These modules are quoted for products that have to report a position or a time, typically where:

Asset trackers and telematics units – a tracker that sleeps for hours needs a fast hot start and a low backup current, and it needs four constellation reception because it is often parked under a deck or beside a container.

UAV and handheld navigation – an update rate of 10 Hz to 25 Hz feeds the flight controller, and the module is read alongside the inertial sensors on the same board.

Telecom and instrumentation timing – a line card uses the 1PPS output as a phase reference and holds over on a local oscillator when the sky view is lost.

The module shares the carrier board with the cellular modem and the power stage, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Sourcing and Cross-Reference

Selection starts with the sky view the product will really have. A roof mounted antenna sees enough satellites for a single constellation part, while a tracker inside a vehicle does not, and the second case needs concurrent reception plus the best tracking sensitivity the budget allows. The next check is the host interface: a module with UART only is enough for a microcontroller that already runs an NMEA parser, and a module with SPI or I2C shortens the read time when the host samples at 10 Hz or faster.

The mechanical side decides the rest. A patch antenna needs a ground plane under it and a keep out area free of copper, battery and metal on both sides of the board, and an active antenna needs a bias tee, a current limit and a feed that survives a short at the connector. A module with the patch built in removes the feed loss but fixes the antenna position inside the enclosure, which is why handheld products often prefer it and vehicle products usually do not.

When a module reaches last time buy or a not recommended status, the replacement is checked on footprint, supply, interface and constellation set at the same time, because a part that matches the pinout but needs a different backup rail will fail in the field rather than on the bench. The route for that check is on our source obsolete components page, and the pin comparison is on pin to pin cross reference. Related families are listed under sensors and detectors and multi function ICs.

For volume builds, SUPERB Assembly support covers the module footprint, the backup rail, the antenna feed and the keep out area on the carrier board.

Q: Can you quote NEO-M8N-0 and a replacement with the same 12.2 x 16.0 mm footprint, and confirm the backup current on the backup pin?

A: Yes. Send the sky view, the supply rail and the host interface, and the SUPERB Tech team will confirm the order code, the sensitivity and the backup current from the maker data sheet before quoting.

Why Buyers Source GNSS Modules Through SUPERB

  1. Sensitivity read from the right row: tracking, cold start and reacquisition figures are quoted separately, because a headline that mixes them is how a receiver ends up short of sensitivity in the field.
  2. Backup rail checked before quoting: the backup pin current and its allowed voltage window are confirmed for the chosen part, which decides between a cell and a supercapacitor.
  3. Antenna requirement stated with the module: ground plane size, keep out and bias tee needs are quoted with the part, so the mechanical team is not surprised after the layout.
  4. Order code confirmed against the maker data sheet: the suffix carries the firmware, the interface and the temperature grade, and two codes that look alike can differ in all three.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: 6 axis IMU sensors for flight control, barometric pressure and altitude sensors, RF transceiver ICs for telemetry, crystal units and TCXO oscillators.