Ambient Light and Proximity Sensors for Display and Presence
Product Specifications
Product Overview
An ambient light sensor is a photodiode with a filter and an ADC on one die. The filter is the part that matters: it shapes the response to follow the human eye and rejects the infrared that a lamp or the sun carries, so the lux figure matches what a person would see rather than what a silicon detector measures. Without that filter a reading under an incandescent lamp is several times too high, and a backlight dims to the wrong level.
Dynamic range is the second figure. A display has to work at 0.1 lx in a dark room and at 80 klx in direct sun, which is almost six decades, and a single gain stage cannot cover that. The parts in this group solve it in two ways: an automatic full scale setting that picks one of twelve ranges, as on the OPT3001, or a 16 bit conversion with a programmable integration time, as on the VEML7700 and the BH1750FVI.
Proximity sensing adds an infrared emitter and a photodiode that measures the reflection. The detection distance is set by the emitter current, the window and the crosstalk between emitter and detector, and the parts here quote a distance with the emitter driven at a stated current. Crosstalk is the figure that limits a product behind thick glass: the light that reflects inside the window arrives at the detector as an offset, and the part has to be able to subtract it.
The table below covers the codes we quote most often: high accuracy lux meters for display dimming, a high sensitivity part for operation behind dark glass, a combined ambient and proximity part with a 200 mm range, a gesture part with four directional photodiodes, and a low cost 16 bit part for appliances. Range, resolution, interface, supply and package come from the maker data sheet for each code.
Key Specifications
| Parameter | Lux meter, display dimming | Ambient plus proximity | Gesture and colour |
|---|---|---|---|
| Ambient light range | 0.01 lx to 83 klx | 0.0125 lx to 6.5 klx, or 0 lx to 140 klx on the 16 bit part | ambient and RGB channels, 16 bit each |
| Resolution | 0.01 lx at the lowest range | 0.0125 lx per step | 16 bit per channel |
| Effective dynamic range | 23 bit with automatic ranging | 16 bit | 16 bit |
| Proximity range | not included | 0 mm to 200 mm | 0 mm to 100 mm |
| Interface | I2C and SMBus, 400 kHz | I2C, 400 kHz | I2C, 400 kHz |
| Supply voltage | 1.6 V to 3.6 V | 2.5 V to 3.6 V, 1.8 V to 3.6 V on the bus | 2.4 V to 3.6 V |
| Current | 1.8 uA in operation | not published as one figure for the family | 1.0 uA in sleep |
| Package | 2.0 mm by 2.0 mm by 0.65 mm | 4.0 mm by 2.0 mm by 1.1 mm | 3.94 mm by 2.36 mm by 1.35 mm |
Included Models and Order Codes
The table lists the codes we quote most often. Range, resolution, interface, supply, current and package come from the maker data sheet for that code. Where a part carries an automotive grade, the grade belongs to a separate order code, and the two are quoted as different numbers.
| Part Number | Function | Ambient range | Resolution | Interface | Supply | Package |
|---|---|---|---|---|---|---|
| OPT3001DNPR | ambient light | 0.01 lx to 83 klx | 0.01 lx at lowest range | I2C, 400 kHz | 1.6 V to 3.6 V | USON 2.0 x 2.0 mm |
| OPT3001IDNPRQ1 | ambient light, AEC-Q100 | 0.01 lx to 83 klx | 0.01 lx at lowest range | I2C, 400 kHz | 1.6 V to 3.6 V | USON 2.0 x 2.0 mm |
| VEML7700-TR | ambient light | 0 lx to 140 klx | 0.0042 lx per count | I2C, 400 kHz | 2.5 V to 3.6 V | 6.8 x 2.35 x 3.0 mm |
| TSL2591 | ambient light, dual channel | 188 ulx to 88 klx | 16 bit per channel | I2C, 400 kHz | 2.7 V to 3.6 V | 2.4 x 2.0 mm |
| VCNL4040 | ambient plus proximity | 0.0125 lx to 6.5 klx | 0.0125 lx per step | I2C, 400 kHz | 2.5 V to 3.6 V | 4.0 x 2.0 x 1.1 mm |
| BH1750FVI | ambient light | 1 lx to 65 klx | 1 lx in high resolution mode | I2C, 400 kHz | 2.4 V to 3.6 V | not published as one body size for the family |
| APDS-9960 | ambient, RGB, proximity, gesture | 16 bit per channel | 16 bit per channel | I2C, 400 kHz | 2.4 V to 3.6 V | 3.94 x 2.36 x 1.35 mm |
Key Features
Filter matched to the human eye – an infrared rejection above 99 percent means a reading under an incandescent lamp or in sunlight tracks what a person sees, which is the basis of a dimming curve.
Automatic full scale – twelve binary weighted ranges with matching better than 0.2 percent let one part cover 0.01 lx to 83 klx without a gain decision in software.
Resolution stated per count – 0.0042 lx per count on one part and 0.0125 lx per step on another are the figures that set the usable low light behaviour behind a dark window.
Proximity with an integrated emitter – a 200 mm detection range with a 200 mA emitter pulse removes the separate emitter, its driver and its alignment step from the board.
Crosstalk handling stated – the proximity parts subtract the internal reflection of the window, which is the figure that decides how thick the cover glass can be.
Interrupt output – a threshold interrupt wakes the host instead of polling, which is what keeps the average current of an always on sensor in the microamp range.
Applications
These parts are quoted for displays and enclosures that react to light or to a hand, typically where:
Display and keypad dimming – a lux meter behind the cover glass sets the backlight, and the infrared rejection keeps the brightness stable when the light source changes from daylight to a filament lamp.
Presence and touchless switching – a proximity part at 200 mm detects a hand at a dispenser, a faucet or a panel, and the interrupt output lets the controller sleep between events.
Gesture and colour sensing – four directional photodiodes read a swipe over a display, and the same die reports the red, green, blue and clear channels for a colour temperature correction.
The sensor sits behind the cover glass of the same product, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.
Sourcing and Cross-Reference
Selection starts with the window. The light that reaches the die passes the cover glass, its print and its air gap, so the transmission of that stack sets the low light limit and the crosstalk sets the proximity range. A part with 0.0042 lx per count behind a 10 percent window behaves like one with 0.042 lx per count, and the data sheet figure is only a starting point.
The second check is the bus and the supply. All the parts in this group talk I2C at 400 kHz, but the supply range differs: 1.6 V to 3.6 V on the OPT3001 and 2.5 V to 3.6 V on the VEML7700, which decides whether the part can hang on a 1.8 V rail directly. The interrupt pin and its polarity are part of the same check.
Where a code has been discontinued, the substitution is checked on spectral response, range, resolution, package outline and the position of the aperture, because a different aperture position changes the window print. One part in this group is now marked obsolete by its maker with no replacement, and those builds are quoted on the nearest equivalent with the differences written out. The route for these checks is on our obsolete part cross reference hub, and the drop in comparison is on pin to pin cross reference.
For volume builds, SUPERB Assembly support covers the aperture in the window print, the light tight gasket around the part and the keep out that stops light piping from the backlight.
Q: Can you supply an ambient light sensor with the infrared rejection and the resolution stated, for a display that runs from 0.1 lx to 60 klx?
A: Yes. Send the light range, the window transmission, the supply rail and the package, and the SUPERB Tech team will confirm the range, the resolution and the interface from the maker data sheet before quoting.
Why Buyers Source Light Sensors Through SUPERB
- Range and resolution quoted together: a lux figure without the resolution behind it does not describe low light behaviour, so both are given with the code.
- Spectral response stated: infrared rejection and peak wavelength are quoted, which is what makes a reading comparable between light sources.
- Supply and bus checked first: 1.8 V and 3.3 V rails are not interchangeable on these parts, so the supply range is confirmed before a code is offered.
- Obsolete codes handled with data: where a maker has ended a part, the nearest equivalent is offered with the aperture and package differences written out.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Sensors and detectors, PIN and avalanche photodiodes, Phototransistors for optical sensing, Temperature and humidity sensors, Logic level shifters and IO expanders, Obsolete part cross reference hub.