Contact Us

Varactor and Tuning Diodes for RF Circuits

Hyperabrupt parts cover 1.4 pF to 12.6 pF at 1 V, with a 1.5 to 2.8 ratio to 3 V and series resistance from 0.6 ohm to 2.9 ohm. The linear UHF part covers 17.5 pF to 21 pF at 0.5 V with an 8.9 to 12 ratio to 28 V. The VHF part covers 26 pF to 32 pF at 3 V with a 5 to 6.5 ratio to 25 V. Reverse voltage, package and power rating are listed per code, because they set the tuning range and the loop.
quote now

Product Specifications

Product Overview

A varactor is a diode used backwards. The depletion region widens as the reverse voltage rises, the capacitance falls, and the slope of that fall is set by the doping profile: a linear junction gives a gentle tuning curve over a wide voltage, and a hyperabrupt junction gives a steep curve at low voltage. That is why the first number on a varactor data sheet is not one capacitance but a pair of them, at two stated voltages, with the ratio between them.

The ratio is what decides whether a part can cover a band. A 1.5 to 1.8 ratio at 1 V to 3 V, as on the SMV1231, covers a narrow trim range around a fixed frequency; a 5 to 6.5 ratio at 3 V to 25 V, as on the BBY40, covers a full VHF band. The absolute capacitance then sets the frequency, because the varactor sits in parallel with the inductor and the total capacitance decides where the tank resonates.

Series resistance is the second figure that matters. It is quoted at a stated frequency and bias, typically 500 MHz at 3 V, and it sets the Q of the tuned circuit and therefore the phase noise of a VCO. A part at 2.9 ohm suits a narrow trim loop; a part at 0.6 ohm to 0.8 ohm suits a high Q resonator. The resistance falls as the capacitance rises, so the two are always read together.

The table below covers the three groups we quote most often: hyperabrupt parts from 1.4 pF to 12.6 pF for low voltage VCO tuning, a UHF linear part at 17 pF to 21 pF for tuner and upconversion circuits, and a VHF part at 26 pF to 32 pF for band A tuning. Capacitance at stated voltages, ratio, series resistance and package come from the maker data sheet for each code.

Key Specifications

ParameterHyperabrupt, low tuning voltageUHF linear, SOD-323VHF linear, SOT-23
Capacitance at 1 V1.43 pF to 12.65 pFnot specified at 1 Vnot specified at 1 V
Capacitance at 0.5 Vnot specified17.5 pF to 21 pFnot specified
Capacitance at 3 V0.97 pF to 6.4 pFnot specified26 pF to 32 pF
Capacitance at 25 V or 28 Vnot specified1.7 pF to 2.1 pF at 28 V4.3 pF to 6 pF at 25 V
Capacitance ratio1.5 to 3.48.9 to 12 at 0.5 V over 28 V5 to 6.5 at 3 V over 25 V
Series resistance0.60 ohm to 2.90 ohm at 500 MHz, 3 V0.75 ohm at 470 MHz0.6 ohm to 0.7 ohm at 200 MHz
Reverse voltage, max15 V30 V30 V
Power dissipation250 mWnot published as a single figure330 mW
PackageSOD-323, SOT-23, SC-70, SC-79SOD-323SOT-23

Included Models and Order Codes

The table lists the codes we quote most often. Capacitance at the stated voltages, ratio, series resistance, reverse voltage and package come from the maker data sheet for each code. The option suffix on a hyperabrupt code sets the package, so the same die is ordered as -079 for SOD-323 and -074 for SOT-23 and the suffix is never dropped from a quotation.

Part NumberCT at 1 VCT at 3 VRatio 1 V / 3 VRS at 3 VVR maxPackage
SMV1231-079LF1.43 pF to 1.72 pF0.97 pF1.5 to 1.82.90 ohm15 VSOD-323
SMV1232-079LF2.34 pF to 2.86 pF1.50 pF1.5 to 1.91.50 ohm15 VSOD-323
SMV1233-079LF3.00 pF to 3.60 pF1.80 pF1.5 to 1.91.20 ohm15 VSOD-323
SMV1234-079LF5.85 pF to 7.15 pF3.60 pF1.6 to 2.00.80 ohm15 VSOD-323
SMV1235-079LF10.35 pF to 12.65 pF6.40 pF1.6 to 2.00.60 ohm15 VSOD-323
BB135,11521 pF at 0.5 Vnot specified at 3 V8.9 to 12 at 0.5 V over 28 V0.75 ohm at 470 MHz30 VSOD-323
BBY40,215not specified at 1 V26 pF to 32 pF5 to 6.5 at 3 V over 25 V0.6 ohm to 0.7 ohm at 200 MHz30 VSOT-23

Key Features

Two capacitances, not one – a varactor is quoted at two reverse voltages with the ratio between them, and a part that looks equal at 1 V can differ by a factor of two in ratio and cannot cover the same band.

Ratio matched to the band – a 1.5 to 1.8 ratio trims a narrow loop around a fixed frequency, a 5 to 6.5 ratio covers a VHF band, and an 8.9 to 12 ratio covers a UHF tuner from 0.5 V to 28 V.

Series resistance read at frequency – 0.6 ohm at 500 MHz and 3 V gives a high Q resonator, 2.9 ohm is a trim element, and the figure is only meaningful with the frequency and bias stated next to it.

Low tuning voltage on hyperabrupt parts – the SMV123x family reaches its full ratio between 1 V and 6 V, so a 3.3 V DAC drives the loop directly without a charge pump.

Reverse voltage sets the loop headroom – 15 V on the hyperabrupt family and 30 V on the linear parts decide how much of the tuning curve a 3.3 V or 5 V control loop can reach.

Package option on the same die – the same hyperabrupt die is offered in SOD-323, SOT-23, SC-70 and SC-79, so the tuning range is unchanged when the assembly moves to a smaller outline.

Applications

These parts are quoted for tuned circuits, typically where:

VCO and PLL tuning – a hyperabrupt part at 3 pF to 7 pF sits across the tank and pulls the frequency over a narrow band, with the loop filter set from the capacitance slope and the control range.

UHF tuner and upconversion – a 17 pF to 21 pF linear part tunes a band A or UHF front end, where the 8.9 to 12 ratio covers the band with one control voltage.

Voltage controlled filters and phase shifters – two matched varactors in a balanced circuit shift phase or tune a filter corner, and the matching between the two parts is the figure that sets the residual amplitude modulation.

The varactor sits in the tuned stage of the same radio board, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Sourcing and Cross-Reference

Selection starts with the tank. The required capacitance at the centre frequency sets the absolute value, the band sets the ratio, and the control voltage available on the board sets which family can reach that ratio. A hyperabrupt part is chosen when the control comes from a 3.3 V DAC; a linear part is chosen when the control sweeps to 25 V or 28 V and the band is wide.

The second check is Q and matching. Series resistance at the operating frequency sets the resonator Q, and where two varactors work as a pair the capacitance matching between them matters more than the absolute tolerance. Both are quoted per code rather than per family.

Where a code has been discontinued, the substitution is checked on capacitance at both voltages, ratio, series resistance and reverse voltage, and on the package suffix that sets the footprint. The route for these checks is on our pin to pin cross reference page, and the wider list is on the obsolete part cross reference hub.

For volume builds, SUPERB Assembly support covers the matched pairs, the ground via placement under the SOD-323 body and the keep out the tuning line needs from the digital section.

Q: Can you supply matched pairs of a hyperabrupt varactor with the capacitance ratio quoted at 1 V and 3 V?

A: Yes. Send the frequency, the tuning voltage range, the capacitance needed at the band edges and the quantity, and the SUPERB Tech team will confirm the ratio, the series resistance and the package from the maker data sheet before quoting.

Why Buyers Source Tuning Diodes Through SUPERB

  1. Capacitance quoted at both voltages: the ratio is the figure that decides band coverage, so it is given with the two capacitances it was measured between.
  2. Series resistance with frequency and bias: the Q of the tuned circuit follows from that figure, and it is quoted as the data sheet states it rather than as a single number.
  3. Package suffix kept on the code: the same die in SOD-323 and SOT-23 is a different order code, so the footprint on the board is confirmed before the part is quoted.
  4. Matched pairs offered: where two varactors work as a pair, capacitance matching is quoted alongside the absolute value.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Frequency converters and sources, VCO and PLL synthesizer ICs, RF switches and PIN diode switches, Baluns and RF transformers, Digital step attenuators, Pin to pin cross reference.