Contact Us
  • Home
  • COMPONENTS
  • Small Signal Bipolar Transistors for Switching and Amplification

Small Signal Bipolar Transistors for Switching and Amplification

The complementary pairs cover 40 V at 200 mA and 45 V at 100 mA in TO-92 and SOT-23. The 800 mA part carries four times the current of the standard switching transistor at 40 V. Gain groups run from 100 to 300 and from 200 to 450, and the group letter is part of the code. Transition frequency, power rating and package are listed per code, because they set the drive.
quote now

Product Specifications

Product Overview

The small signal bipolar transistor has not been replaced. A MOSFET needs several volts on its gate to reach a low resistance, a bipolar needs 0.7 V on its base and a base resistor, and for a relay coil, an LED string or a logic level shift at a few tens of milliamps the bipolar is still the smaller and cheaper switch. The two families in this group, the 2N390x and the BC54x to BC55x, cover most of that work.

The first figure that matters is the gain group. A BC547B is specified at 200 to 450 of hFE at 2 mA, while the A group is 110 to 220 and the C group is 420 to 800, and the letter after the number is part of the order code. A circuit built around a B part and built with a C part still works, but a circuit built around a C part and built with an A part may not saturate, which is why the group is never dropped from a quotation.

The second figure is the transition frequency. A 2N3904 at 300 MHz and a BC847B at 100 MHz are the same kind of part on paper, and the difference shows up when the transistor is used as a small signal amplifier rather than a switch: the 100 MHz part has less gain at 10 MHz, and a stage built for one behaves differently with the other. For switching duty at kilohertz rates either is fine.

The table below covers the codes we quote most often: the 2N3904 and 2N3906 complementary pair in TO-92 and SOT-23, the 2N2222A for higher current, the BC547B and BC557B pair in TO-92, and the BC847B and BC857B pair in SOT-23 for surface mount boards. Voltage, current, gain group, transition frequency, power and package come from the maker data sheet for each code.

Key Specifications

Parameter2N3904 / 2N3906 pair2N2222ABC547B / BC557B pairBC847B / BC857B pair
PolarityNPN and PNPNPNNPN and PNPNPN and PNP
Collector emitter voltage40 V40 V45 V45 V
Collector current, continuous200 mA800 mA100 mA100 mA
DC current gain at 10 mA100 to 300100 to 300 at 150 mA200 to 450 at 2 mA200 to 450 at 2 mA
Transition frequency300 MHz NPN, 250 MHz PNP300 MHz300 MHz100 MHz
Power dissipation at 25 C625 mW in TO-92, 350 mW in SOT-23500 mW625 mW250 mW
Saturation voltage at 10 mA0.2 V NPN, 0.25 V PNP0.3 V at 150 mA0.25 V0.2 V
PackageTO-92 and SOT-23TO-18TO-92SOT-23

Included Models and Order Codes

The table lists the codes we quote most often. Polarity, voltage, current, gain group, transition frequency, power and package come from the maker data sheet for that code. The gain group letter and the package suffix are both part of the order number, so BC547B and BC547C are different codes and MMBT3904 is not the same order line as 2N3904.

Part NumberTypeVCEOIC maxhFE groupfTPowerPackage
2N3904NPN40 V200 mA100 to 300 at 10 mA300 MHz625 mWTO-92
2N3906PNP-40 V200 mA100 to 300 at 10 mA250 MHz625 mWTO-92
MMBT3904NPN40 V200 mA100 to 300 at 10 mA300 MHz350 mWSOT-23
2N2222ANPN40 V800 mA100 to 300 at 150 mA300 MHz500 mWTO-18
BC547BNPN45 V100 mA200 to 450 at 2 mA300 MHz625 mWTO-92
BC557BPNP-45 V100 mA200 to 450 at 2 mA300 MHz typical500 mWTO-92
BC847BNPN45 V100 mA200 to 450 at 2 mA100 MHz250 mWSOT-23
BC857BPNP-45 V100 mA200 to 450 at 2 mA100 MHz250 mWSOT-23

Key Features

Gain group is part of the code – the letter after the number sets hFE from 110 to 220, 200 to 450 or 420 to 800, and a circuit that saturates with one group may not with another.

Complementary pairs in stock together – the NPN and PNP parts of a pair share voltage, current and package, so a push pull stage or a level shifter is quoted as one line.

Current step within one family – the 2N2222A carries 800 mA in the same TO-18 style as the 200 mA parts, which covers a relay coil or a small lamp without moving to a power device.

Transition frequency stated – 300 MHz on the 2N3904 and 100 MHz on the BC847B decide whether the part works as an amplifier at a few megahertz or only as a switch.

Power rating with the package – 625 mW in TO-92, 350 mW in SOT-23 and 250 mW on the BC847B set the base drive and the collector load that the part can carry without a heatsink.

Saturation voltage quoted – 0.2 V to 0.3 V at 10 mA is the figure that decides the base resistor, because the base current has to be a tenth of the collector current or more to reach it.

Applications

These parts are quoted for boards that switch a load or bias a stage, typically where:

Relay, lamp and LED switching – a 2N2222A or a BC547B drives a coil or an LED string from a logic pin, with the base resistor set from the gain group and the collector current.

Level shifting and signal inversion – a complementary pair shifts a 3.3 V logic level to a 12 V rail or inverts a signal, where the 40 V to 45 V rating leaves margin on a 24 V system.

Small signal amplification – a 2N3904 at 300 MHz or a BC547B at 300 MHz biases a first stage in an audio or an instrument front end, where the gain group sets the operating point.

The transistor sits in the driver stage of the same board, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Sourcing and Cross-Reference

Selection starts with the duty. For a switch, the numbers that matter are the collector current, the saturation voltage at that current and the gain group, because together they set the base resistor. For an amplifier, the transition frequency and the gain at the working current matter more than the maximum ratings, and the two uses lead to different codes even inside one family.

The second check is the package and the power. A TO-92 part dissipates 625 mW at 25 C and a SOT-23 part 250 mW to 350 mW, so the same die in a smaller body carries less current before it overheats, and the copper area on the board is part of that figure.

Where a code is short, the substitution is checked on polarity, voltage, current, gain group, transition frequency and pinout, and the pinout is the one that catches people: the 2N3904 in TO-92 is EBC while some BC parts are CBE, so a substitute that matches electrically can be wired backwards. The route for these checks is on our pin to pin cross reference page, and the wider list is on the obsolete part cross reference hub.

For volume builds, SUPERB Assembly support covers the pinout check between TO-92 and SOT-23 parts, the base resistor placement and the thermal copper under a SOT-23 that carries a coil.

Q: Can you supply a matched NPN and PNP pair in SOT-23 with the gain group stated on the order code?

A: Yes. Send the polarity, the voltage and current, the gain group, the package and the quantity, and the SUPERB Tech team will confirm the hFE range, the transition frequency and the pinout from the maker data sheet before quoting.

Why Buyers Source Small Signal Transistors Through SUPERB

  1. Gain group kept on the code: the letter that sets hFE is confirmed against the data sheet, so a B group part is not replaced by an A group part.
  2. Pinout checked before substitution: TO-92 pinouts differ between families, and the order is confirmed rather than assumed from the electrical match.
  3. Pairs quoted together: the NPN and PNP complements are listed side by side with the same voltage and package.
  4. Power matched to the package: TO-92 and SOT-23 ratings are given with the code, so the collector load is set from the body that will be placed.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Discrete and power semiconductors, Power MOSFETs for motor drive, Gate driver chips for motor control, Bridge rectifiers and Schottky rectifiers, LED indicators and optocouplers, Pin to pin cross reference.