Contact Us
  • Home
  • COMPONENTS
  • High Power LED Emitters for Illumination and Infrared

High Power LED Emitters for Illumination and Infrared

A high power emitter is a thermal part before it is an optical part, because the flux figure is quoted at a junction temperature the board has to hold. White parts on this page run to 2000 mA and infrared parts to 2 A pulsed, and both need a metal core board and a defined solder pad. Flux bins and forward voltage are given per order code, since the same family ships in several bins. Every row lists drive current, forward voltage and viewing angle.
quote now

Product Specifications

Product Overview

The flux printed on a high power LED data sheet is measured at a stated junction temperature, usually 85 C, and at a stated current. Both conditions have to be met by the board, not by the bench supply. That is why two builds using the same emitter can differ by more than 20 percent in light output: one keeps the thermal pad soldered to a metal core board with a full via field, the other mounts the same part on 1 oz FR-4 with a thermal relief.

White emitters split into two classes on this page. The 3535 class, such as the LUXEON 3535L parts at 200 mA and 3.4 V, is the workhorse for indicator panels, backlights and small area lighting, where 33 to 44 lumens per part is enough and the drive current keeps the thermal stack simple. The ceramic class, such as the Cree XP-G3 order codes at up to 2000 mA, is used where a single part has to deliver 150 lumens or more, and there the junction temperature and the solder pad shape decide the lifetime.

Infrared emitters are specified on radiant intensity and on pulse conditions, not on lumens. The Osram SFH 4715A at 850 nm reaches 940 mW/sr at 2 A with a 100 microsecond pulse, and the same part is quoted at 860 mW total radiant flux at 1 A, which is the figure that matters for a camera illumination job. Pulse width and duty cycle have to be read together with the current, because the thermal resistance is given for a single 1 microsecond pulse as well as for continuous operation.

The 850 nm and 940 nm choice is not cosmetic. A 940 nm emitter is far less visible to the eye, which matters for covert illumination and for consumer devices where a red glow is a complaint, while 850 nm gives more silicon response per watt for a given camera. Both need a bandpass filter in front of the sensor if the unit works in daylight, because the sun carries more energy at those wavelengths than the emitter does.

Assembly rules for this class are short and unforgiving. The emitter must be reflowed on a lead free profile that the maker publishes, the thermal pad must not be hand soldered, and no flux residue may remain on the silicone because it will carbonise. A part that has been reworked twice has lost part of its lifetime, and that is a cost the customer pays in the field rather than in the build.

Key Specifications

ParameterValueApplies to
Maximum drive current200 mA continuousLUXEON 3535L parts
Maximum drive current2000 mA continuousXP-G3 order codes
Forward voltage at 350 mA, 85 C2.73 V typicalXP-G3
Forward voltage at 350 mA, 25 C2.93 V typical at 700 mAXP-G3
Luminous flux at 350 mA156 lm at 85 C, 170 lm at 25 CXPGDWT-H1-0000-00KCB
Luminous flux at 350 mA172 lm at 85 C, 187 lm at 25 CXPGDWT-01-0000-00M50
Viewing angle, full width half maximum125 degreesXP-G3
Viewing angle115 degreesLUXEON 3535L
Junction temperature limit150 CXP-G3
Peak wavelength850 nmSFH 4715A and SFH 4715AS
Radiant intensity940 mW/sr at 2 A, 100 microsecond pulseSFH 4715A
Thermal resistance junction to solder point9.0 K/W max, 6.6 K/W on the A01 versionSFH 4715A, SFH 4715AS A01
ESD withstandClass 3A HBM, 8 kV on A01XP-G3, SFH 4715AS A01

Included Models and Order Codes

Order codes below are complete, including the flux and chromaticity bin, because a family name alone does not fix the output. Where a maker has marked a part as not for new use, that status is written next to it so a new build is not planned around a part that is leaving the catalogue.

Order CodeColour or wavelengthDrive currentForward voltageOutputPackage
XPGDWT-H1-0000-00KCBWhite 6500 K, 80 CRI minimum, S3 bin2000 mA max2.73 V at 350 mA, 85 C156 lm at 350 mA, 85 C3.45 mm ceramic
XPGDWT-01-0000-00M50White 6000 K, 70 CRI, S5 bin2000 mA max2.73 V at 350 mA, 85 C172 lm at 350 mA, 85 C3.45 mm ceramic
MXA8-PW30-0000LUXEON 3535L, white 3000 K, 80 CRI200 mA max3.4 V44 lm, 115 degree beam3535 SMT
MXA8-PW22-0000LUXEON 3535L, white 2200 K, 80 CRI200 mA max3.4 V33 lm, 115 degree beam3535 SMT
SFH 4715AInfrared 850 nm, Oslon Black, marked not for new use2 A pulsed2.05 V at 2 A940 mW/sr at 2 A, 860 mW flux at 1 AOslon Black SMT
SFH 4715ASInfrared 850 nm, double stack emitter1.5 A pulsed3.05 V at 1.5 A900 mW/sr at 1 AOslon Black SMT
SFH 4715AS A01Infrared 850 nm, AEC-Q102 qualified, 80 degree1.5 A pulsed3.05 V at 1.5 A1150 mW/sr at 1.5 AOslon Black SMT

Key Features

Flux quoted at 85 C – Every white part on this page states the flux at 85 C as well as at 25 C, so a product is not built on a cold bench number.

2000 mA drive on a ceramic package – The XP-G3 order codes take 2000 mA with a 150 C junction limit, which lets one part replace several smaller emitters.

3535 footprint at 200 mA – The LUXEON 3535L parts drop onto an existing 3535 pad and run from 3.4 V at 200 mA, which keeps the driver simple and the board cool.

Double stack infrared – The SFH 4715AS doubles the emitting area for the same footprint, which raises radiant intensity for a camera illuminator without a second part.

AEC-Q102 option – The SFH 4715AS A01 version carries the automotive qualification and a 6.6 K/W thermal resistance, which is what a vehicle interior build needs.

Pulse ratings published – Radiant intensity is given with the test pulse width and current, so the achievable output at a given duty cycle can be read directly.

Applications

These emitters fall into three groups by end use: general lighting, machine vision illumination and infrared sensing.

Panel and area lighting – LUXEON 3535L parts in 2200 K to 3000 K run at 200 mA on a low cost aluminium board, which suits downlights and retrofit lamps.

Machine vision and CCTV – 850 nm emitters at 940 mW/sr illuminate a scene for a silicon camera, and the pulse rating lets a strobe stage run well above the continuous limit.

Automotive interior sensing – The AEC-Q102 qualified 850 nm part with 6.6 K/W thermal resistance suits driver monitoring and in cabin sensing where the board sits behind a plastic lens.

Emitters are quoted against the SUPERB PCB and the SUPERB PCBA build at the same time, so the thermal pad and the driver current are checked as one decision rather than two.

Sourcing and Cross-Reference

Emitter supply moves with bin, not with part number. A 6500 K 80 CRI part and the same family in a different flux bin carry the same order code prefix, so a shortage on one bin can often be covered by a higher bin, which is acceptable for most lighting builds and not acceptable for a colour critical one. We ask which bins the drawing allows before offering a substitute.

Second sourcing a high power emitter needs the pad geometry and the thermal pad polarity to match, not just the colour and the flux. A part that is electrically similar but has the thermal pad on the opposite side will not drop onto the board, and forcing it changes the thermal path. We quote the footprint, the pad drawing and the reflow profile with every alternative.

Parts that a maker has marked as not for new use are still available and are often the only option for a service build. We state that status in the quote so a customer can decide between a lifetime buy and a new footprint, and we do not present such a part as the current offering.

SUPERB Assembly reflows the emitter on the maker profile and keeps the thermal pad off the hand soldering bench, which is where most of the lifetime is lost.

Q: Can you supply the same emitter in a different flux bin when the original bin is not available?

A: The bin and the CRI decide it; the SUPERB Tech desk checks which bins the order can ship and states the difference in output before an alternative is offered.

Why Buy LED Emitters Through SUPERB

  1. Bin level quoting: Quotes name the flux and chromaticity bin, so a lighting build does not receive a part that measures outside the drawing.
  2. Thermal data included: Every quote carries the thermal resistance and the junction limit, which are the two numbers the board stack is checked against.
  3. Emitter and driver together: Because the same build carries the constant current driver, the drive current and the thermal pad are checked together.
  4. Status shown, not hidden: Parts marked not for new use are flagged, so a service build and a new product are not quoted the same way.
  5. One shipment with the board: Emitters ship with the assembled board, which avoids a bin mismatch between a reel bought separately and the build it was meant for.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: LED Indicators and Optocouplers, Constant Current LED Driver ICs, TVS and ESD Protection Diodes, Ambient Light and Proximity Sensors.