Contact Us

Zener Diodes for Voltage Reference and Clamping

Axial 1 W parts cover 3.3 V to 56 V in DO-41, with test currents from 76 mA down to 4.5 mA. Axial 0.5 W parts in DO-35 cover the same voltage range at 20 mA test current. Surface mount parts in SOT-23 cover 5.6 V to 39 V at 5 mA and 300 mW. Zener impedance and reverse leakage are listed per code, because they decide the regulation and the loading.
quote now

Product Specifications

Product Overview

A zener diode is used in two different ways, and the data sheet figure that matters changes with the use. As a shunt reference the diode runs at a steady test current and the load hangs in parallel, so the output is the zener voltage plus the impedance times the current change, and the impedance at the test current is the number that sets the regulation. As a clamp the diode sits off until a fault drives it into breakdown, and the numbers that matter are the knee impedance and the peak power the junction can take before it fails.

Test current is therefore not a detail. A 1N4733A is specified at 49 mA, so its 7 ohm impedance is quoted at that current; run the same part at 2 mA and the impedance is several times higher and the output moves with every load step. A part intended for a low current reference is specified at 5 mA or 20 mA instead, which is why the 0.5 W and SOT-23 families exist next to the 1 W axial parts.

Power has to be read with the thermal path. A 1 W DO-41 part reaches its rating only with the lead at 50 C and a defined lead length; on a board at 70 C the same part dissipates about 0.87 W. The SOT-23 parts are quoted at 300 mW on a standard footprint, and the same die in a larger package is quoted higher, so the package and the copper area belong in the calculation.

The table below covers the three groups we quote most often: 1 W axial parts in DO-41 from 3.3 V to 56 V, 0.5 W axial parts in DO-35 for boards that cannot take a 1 W body, and SOT-23 parts from 5.6 V to 39 V for surface mount clamps and references. Voltage range, test current, impedance and leakage come from the maker data sheet for each code.

Key Specifications

ParameterAxial 1 W, DO-41Axial 0.5 W, DO-35Surface mount 0.3 W, SOT-23
Zener voltage range3.3 V to 56 V2.4 V to 5.1 V, wider range on request5.6 V to 39 V
Test current76 mA down to 4.5 mA20 mA5 mA
Zener impedance at test current7 ohm to 110 ohm17 ohm to 60 ohm40 ohm at 5.6 V
Reverse leakage100 uA down to 5 uA1 uA at 1 V1 uA at 2 V on the 5.6 V part
Tolerance on nominal voltageplus or minus 5 percentplus or minus 5 percentplus or minus 5 percent, 2 percent on B suffix
Power dissipation1 W at 50 C lead, derate 6.67 mW per C0.5 W at 25 C ambient300 mW on standard footprint, 430 mW by die rating
Operating junction temperature-65 C to +200 C-55 C to +175 C-55 C to +150 C
PackageDO-41 axialDO-35 axialSOT-23

Included Models and Order Codes

The table lists the codes we quote most often. Nominal voltage, test current, impedance, leakage and package come from the maker data sheet for that code. The letter suffix is part of the number: 1N4733A is a 5 percent part at 5.1 V, and the test current in the table applies to that code only.

Part NumberVZ nomVZ rangeIZTZZT maxIR maxPowerPackage
1N4728A3.3 V3.135 V to 3.465 V76 mA10 ohm100 uA at 1 V1 WDO-41
1N4733A5.1 V4.845 V to 5.355 V49 mA7 ohm10 uA at 1 V1 WDO-41
1N4740A10 V9.5 V to 10.5 V25 mA7 ohm10 uA at 7.6 V1 WDO-41
1N4742A12 V11.4 V to 12.6 V21 mA9 ohm5 uA at 9.1 V1 WDO-41
1N4750A27 V25.65 V to 28.35 V9.5 mA35 ohm5 uA at 20.6 V1 WDO-41
1N4758A56 V53.2 V to 58.8 V4.5 mA110 ohm5 uA at 42.6 V1 WDO-41
BZX84C5V65.6 V5.2 V to 6.0 V5 mA40 ohm1 uA at 2 V300 mWSOT-23

Key Features

Test current stated with the impedance – the 7 ohm figure on a 1N4733A holds at 49 mA, so a divider that runs the diode at 2 mA is quoted with the impedance at that current rather than the headline value.

Voltage range given per code – a 5 percent part at 5.1 V is delivered between 4.845 V and 5.355 V, and the range is listed per code so a reference that needs 1 percent is not quoted against a 5 percent table.

Leakage quoted at a stated reverse voltage – 1 uA at 2 V on the 5.6 V part and 5 uA at 42.6 V on the 56 V part are different tests, and the clamp level of a protection circuit depends on which one applies.

Power read from the thermal condition – 1 W at 50 C lead with a defined lead length derates to about 0.87 W at 70 C, so the resistor feeding the diode is sized for the board temperature rather than for the headline rating.

Package matched to the board – DO-41 for through hole power rails, DO-35 where the body has to stay small, and SOT-23 for surface mount clamps, with the same nominal voltages available in more than one of the three.

Knee impedance for clamp duty – the impedance at a fraction of the test current is what sets the clamp voltage during a surge, and it is quoted per code instead of being taken from the nominal voltage alone.

Applications

These parts are quoted for rails that need a reference or a clamp, typically where:

Gate and rail clamping in power stages – a 12 V or 15 V zener holds the gate source voltage of a MOSFET or IGBT below its limit, and the same part protects the driver output against a spike from the power loop.

Shunt reference in measurement circuits – a 5.1 V part at 49 mA test current feeds a divider or an ADC reference, and the code is chosen for the impedance at the current the divider actually draws.

Overvoltage protection on interface lines – a 5.6 V to 12 V SOT-23 part clamps a signal line at the connector, where the small body and the 300 mW rating fit next to the transceiver.

The zener sits on the rail of the same board, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Sourcing and Cross-Reference

The first decision is where the diode sits. On a shunt reference the current through the diode is set by a resistor and varies with the load, so the part is chosen for the impedance at the lowest current it will see, and the resistor is sized for the highest line voltage. On a clamp the diode is off in normal operation and the choice is made on the knee and on the peak power the junction can absorb for the duration of the fault.

The second decision is tolerance and package. A 5 percent axial part covers most clamps, a 2 percent SMD part covers a reference, and a 1 percent requirement moves to a reference IC instead of a zener. The package follows the assembly: DO-41 for a through hole line, DO-35 where height is limited, SOT-23 where the board is surface mount only.

Where a code is hard to find, the substitution is checked on nominal voltage, test current, impedance and power at once, because two parts with the same nominal voltage can differ by a factor of three in impedance and by a factor of two in power. The route for these checks is on our obsolete part cross reference hub, and the drop in comparison is on pin to pin cross reference.

For volume builds, SUPERB Assembly support covers the axial forming, the polarity check and the thermal pad the 1 W body needs on a dense board.

Q: Can you supply a 1 W axial zener with the impedance figure at the current our divider actually runs?

A: Yes. Send the nominal voltage, the tolerance, the current the part will carry and the package, and the SUPERB Tech team will confirm the range, the impedance and the leakage from the maker data sheet before quoting.

Why Buyers Source Zeners Through SUPERB

  1. Voltage range read from the code: the nominal voltage and the tolerance letter are checked against the data sheet table, so a 5 percent part is not sent where the BOM asks for 2 percent.
  2. Impedance quoted at a real current: the test current is given with the impedance, which is the pair that decides the regulation of a shunt reference.
  3. Power matched to the board temperature: the derating curve is applied to the actual ambient, so the resistor feeding the diode is sized once.
  4. Axial and SMD quoted from one table: DO-41, DO-35 and SOT-23 parts are listed side by side, so a board change does not force a new search for the same voltage.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Discrete and power semiconductors, Bridge rectifiers and Schottky rectifiers, Varistors and gas discharge tubes, TVS and ESD protection diodes, PWM controllers for switching supplies, Obsolete part cross reference hub.