Tactile and Slide Switches for Front Panel Control
Product Specifications
Product Overview
Most panel switches switch less than 50 milliamps into a microcontroller input, so the contact rating is rarely the limit. What limits a panel is the feel and the life: an operator presses a key several hundred times a day, and a switch rated at 100,000 operations will be worn out inside a year in that use. The 6 by 6 mm tactile family solves this by offering the same footprint in three forces with three different lives, which is why the force column decides the part.
The sealed SMT parts on this page, the B3S series, carry a rubber seal over the plunger and are built for a board that is washed after reflow. They are rated for 1 to 50 mA at 3 to 24 VDC with a contact resistance of 100 milliohms maximum and an operating temperature of -25 to 70 C, and they come in two forces, 1.57 N and 2.26 N. The seal is what allows the wash, not a higher current rating.
The B3FS family is the open SMT version at the same 6 by 6 mm footprint. Its published life is tied to force: 1,000,000 operations at 0.98 N, 300,000 at 1.47 N and 100,000 at 2.55 N. A panel that needs a light touch and a long life takes the 0.98 N part, while a panel that must not be pressed by accident takes the 2.55 N part and accepts the shorter life. Both are IP00 and cannot be washed, so they are placed after the cleaning step or the board is cleaned before they are added.
Through hole tactile switches such as the 12 by 12 mm part with a 7.3 mm height are used where the switch is the mechanical support as well as the contact, for example a key that passes through a front panel. They carry 50 mA at 24 V and take a 2.6 N force, which is heavy enough that an accidental brush does not trigger the function.
Slide switches are a different animal. The small SPDT part in this list carries 0.1 A at 12 VDC, has 2 mm of travel and is rated for 10,000 operations, which is the right order for a mode selector that is set once per shift rather than pressed. Reading the life figure before choosing between a slide and a tactile part avoids the common mistake of using a slide switch as an everyday key.
Key Specifications
| Parameter | Value | Applies to |
|---|---|---|
| Contact rating | 1 to 50 mA at 3 to 24 VDC | B3S, B3FS |
| Contact rating | 50 mA at 24 VDC | B3F-4055 |
| Contact rating | 0.1 A at 12 VDC | OS102011MS2QN1 |
| Operating force | 0.98 N, 1.47 N, 2.55 N | B3FS series |
| Operating force | 1.57 N, 2.26 N | B3S series |
| Operating force | 2.6 N | B3F-4055 |
| Contact resistance | 100 mOhm max | B3S, B3FS |
| Contact form | SPST-NO | B3S, B3FS, B3F-4055 |
| Contact form | SPDT, ON-ON, non shorting | OS102011MS2QN1 |
| Travel | 2.00 mm | OS102011MS2QN1 |
| Cycle life | 1,000,000 at 0.98 N, 300,000 at 1.47 N, 100,000 at 2.55 N | B3FS series |
| Cycle life | 10,000 electrical and mechanical | OS102011MS2QN1 |
| Operating temperature | -25 to 70 C, -30 to 70 C | B3S and B3FS, slide switch |
| Sealing | Sealed plunger, IP00 | B3S, B3FS |
Included Models and Order Codes
The parts below cover the two shapes a panel usually needs: a 6 by 6 mm tactile switch for a keypad and a slide switch for a mode selector. Force and cycle life come from the maker data sheet, and they move together, so the lightest part is also the longest lived.
| Part Number | Type | Operating force | Contact rating | Height | Cycle life |
|---|---|---|---|---|---|
| B3FS-1000P | SMT tactile, 6 by 6 mm, sealed tape pack | 0.98 N | 1 to 50 mA, 3 to 24 VDC | 3.1 mm | 1,000,000 operations |
| B3FS-1012P | SMT tactile, 6 by 6 mm | 1.47 N | 1 to 50 mA, 3 to 24 VDC | 4.3 mm | 300,000 operations |
| B3FS-1015P | SMT tactile, 6 by 6 mm | 2.55 N | 1 to 50 mA, 3 to 24 VDC | 4.3 mm | 100,000 operations |
| B3S-1000P | SMT tactile, sealed plunger | 1.57 N | 1 to 50 mA, 3 to 24 VDC | 4.3 mm | Per maker data sheet |
| B3S-1002P | SMT tactile, sealed plunger, high force | 2.26 N | 1 to 50 mA, 3 to 24 VDC | 4.3 mm | Per maker data sheet |
| B3F-4055 | Through hole tactile, 12 by 12 mm | 2.6 N | 50 mA at 24 VDC | 7.3 mm | 1,000,000 operations |
| OS102011MS2QN1 | Slide switch, SPDT ON-ON, through hole | 2.00 mm travel | 0.1 A at 12 VDC | 4 mm knob | 10,000 operations |
Key Features
Force and life in one table – The three B3FS forces carry three different lives, so the feel and the service interval are chosen together rather than separately.
Sealed plunger for washing – The B3S series seals the plunger and is meant for a board that is washed after reflow, which the open B3FS parts are not.
Same footprint across forces – A panel can move from 0.98 N to 2.55 N without changing the board, which is useful when the feel is settled late in the programme.
High force panel keys – A 12 by 12 mm through hole part at 2.6 N gives a key that a brush against the panel will not trigger.
Slide switch for mode selection – A 10,000 operation part is matched to a selector that is set per shift, and using it as a daily key is what wears it out early.
Tape and reel packaging – The SMT parts are supplied on embossed tape, so they are placed by the same machine as the rest of the board.
Applications
Panel switches fall into two uses: something pressed many times a day, and something set once and left alone.
Keypads on instruments – Six B3FS-1000P parts at 0.98 N give a light keypad with a million operation life, which is what a bench instrument with a numeric entry needs.
Sealed control boards – B3S parts with a sealed plunger survive a board wash, which suits a controller that is cleaned after reflow before conformal coating.
Mode selectors – An SPDT slide switch with 2 mm travel and 10,000 operations selects a range or a mode on a panel where the setting changes per shift.
Switches are quoted with the SUPERB PCB and the SUPERB PCBA build in mind, so the wash step decides the part before the footprint is committed.
Sourcing and Cross-Reference
Switch shortages are usually about force and sealing, not about size. When a sealed 1.57 N part is quoted long, the open part at the same force has the same footprint and the same electrical rating, and the only change is that it must be placed after the wash. That is a process decision, so we quote both and state the difference.
Counterfeit tactile switches are a real risk on the small 6 by 6 mm parts, because the outline is easy to copy and the force is not. We supply with the maker tape and the date code, and a first article force check on a sample is part of the incoming routine we recommend for any second source.
Slide switches are often the last part to be qualified and the first to be obsoleted, since the small SPDT types are shared across many consumer products. When a part goes, the replacement has to match the travel, the actuator height and the panel cutout, and the electrical rating matters less because the load is usually a logic input.
SUPERB Assembly places the sealed parts before the wash and the open parts after it, which is the one rule that keeps a panel board clean and clickable.
Q: Can you supply a tactile switch with the same footprint but a higher operating force?
A: Force and scrub life decide it; the SUPERB Tech desk quotes the same footprint in each force step so the panel feel can be settled without a board change.
Why Buy Switches Through SUPERB
- Force matched to the panel: Quotes list the force and the life together, so a panel does not get a switch that wears out inside a year.
- Sealed and open options: Both are quoted at the same footprint, so the wash process decides the part rather than the layout.
- Maker tape and date code: SMT switches arrive on the maker tape with traceable lots, which is the basis of a force check on incoming inspection.
- Assembly line feedback: The parts are placed on our own builds, so a footprint or tape problem is caught before the reel reaches a customer line.
- One BOM line: Switches, connectors and the assembled board ship together, which removes a small order that would otherwise hold the build.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Board-to-Board and FPC Connectors, LED Indicators and Optocouplers, OLED and Character LCD Display Modules, Common Mode Chokes and Power Inductors.