Time-of-Flight Distance Sensors for Ranging and Presence
Product Specifications
Product Overview
A time of flight sensor fires a short infrared pulse and measures how long the light takes to return. Light travels about 300 mm in a nanosecond, so a 3 m round trip is 20 nanoseconds, and the sensor resolves that with a single photon avalanche diode array and a time to digital converter inside the package. The result is a distance in millimetres that does not depend on how bright or how dark the target is, which is the property that separates it from a reflective optical sensor or an ultrasonic ranger.
The range figures are quoted for a white target at room light and need to be read with that condition. The VL53L0X reaches 2 m in long range mode, the VL53L1X reaches 4 m, the VL53L3CX reaches 5 m, and the VL53L5CX reaches 4 m across a 65 degree diagonal field split into 64 zones. A dark target at 2 m, or a target at an angle, cuts those figures, and strong sunlight adds ambient photons that raise the noise floor. A product that must work outdoors is specified with a shorter range and a narrower field than the data sheet headline.
The field of view decides the mounting geometry. A 25 degree part measures the distance to whatever is in a cone about 30 cm across at 70 cm, which is the right shape for a laptop lid or a soap dispenser. A 65 degree diagonal part at 40 cm covers a 50 cm wide area in 64 zones, which is the shape for a doorway, a bin or a robot bumper. The zoned parts also report a target status per zone, so the host can tell a flat wall from a person and can ignore a zone where the cover glass has a smudge.
The optical stack is where the mechanical work sits. The emitter and the detector sit side by side under one window, so light from the emitter that reflects off the inside of the cover glass arrives at the detector before the target return. The sensor has a crosstalk calibration for that, and the cover glass has to be at least 1 mm away from the package, flat, and free of a step that would bounce light across. A tinted window that passes 940 nm is fine, and a window that blocks it turns the sensor into a random number generator.
The host side is simple. Every part in this range talks over I2C at up to 400 kHz, the VL53L5CX also offers SPI, and the address can be changed at run time so several sensors share one bus. Update rate runs from 50 Hz on the VL53L0X to 100 Hz on the VL53L1X and VL53L3CX, and a zoned part at 60 Hz with 64 zones moves 64 times the data, so the bus budget is worth checking before the board is frozen.
The tables below list the parts we quote most often for presence detection, level sensing and obstacle avoidance. Range, field of view, update rate and interface come from the maker data sheet and the module documentation for each order code.
Key Specifications
| Parameter | VL53L0X | VL53L1X | VL53L3CX | VL53L5CX |
|---|---|---|---|---|
| Ranging principle | 940 nm class 1 emitter with single photon avalanche detector | 940 nm class 1 emitter with single photon avalanche detector | 940 nm class 1 emitter, multi target detection | 940 nm class 1 emitter, 64 zone array |
| Maximum range | 200 cm | 400 cm | 500 cm | 400 cm |
| Minimum range | About 3 cm | 4 cm | 1 cm | 2 cm |
| Field of view | 25 degrees | 15 to 27 degrees, programmable | 25 degrees | 65 degrees diagonal |
| Zones | Single zone | Single zone with programmable region of interest | Single zone, multi target per reading | 8 by 8 zones |
| Maximum update rate | 50 Hz | 100 Hz | 100 Hz | 60 Hz |
| Interface | I2C up to 400 kHz | I2C up to 400 kHz | I2C up to 400 kHz | I2C or SPI |
| Supply voltage | 2.6 V to 3.5 V | 2.6 V to 3.5 V | 2.6 V to 3.5 V | 3.3 V nominal |
| Active current | 20 mA typical, 40 mA peak | 20 mA typical, 40 mA peak | 20 mA typical, 40 mA peak | 100 mA typical |
| Cover glass | At least 1 mm from the package, no step in the window | At least 1 mm from the package, no step in the window | At least 1 mm from the package, no step in the window | Air gap and crosstalk calibration per zone |
Included Models and Order Codes
The order codes below are the ones we quote most often. The range column is the data sheet maximum against a white target at room light, and the minimum range is the dead zone in front of the window where the reading is not valid. Where a figure is not published for that exact code the cell is left empty rather than copied from a sister part.
| Part Number | Maximum range | Minimum range | Field of view | Update rate | Interface | Note |
|---|---|---|---|---|---|---|
| VL6180X | 60 cm | About 1 cm | 25 degrees | 150 Hz on the carrier | I2C | Also reports ambient light level |
| VL53L4CD | 120 cm | 1 cm | 18 degrees | 100 Hz | I2C | Short range, high accuracy |
| VL53L0X | 200 cm | About 3 cm | 25 degrees | 50 Hz | I2C | Long range mode selects the 2 m setting |
| VL53L1X | 400 cm | 4 cm | 15 to 27 degrees programmable | 100 Hz | I2C | Region of interest can be reduced for a narrow beam |
| VL53L3CX | 500 cm | 1 cm | 25 degrees | 100 Hz | I2C | Reports several targets in one field |
| VL53L5CX | 400 cm | 2 cm | 65 degrees diagonal | 60 Hz | I2C or SPI | 64 zones with a target status per zone |
| VL53L7CX | 350 cm | 2 cm | 90 degrees diagonal | 60 Hz | I2C or SPI | 64 zones, wide angle for room coverage |
| VL53L8CX | 400 cm | 2 cm | 65 degrees diagonal | 60 Hz | I2C or SPI | 64 zones, lower power than the L5CX |
Key Features
Reading independent of target colour – the measurement is a flight time, so a black rubber mat and a white wall at the same distance return the same figure, which a reflective optical sensor cannot do.
Zoned output for presence – the 8 by 8 parts report a small depth map, so a doorway can be watched for a person rather than for any object that crosses one beam.
Class 1 emitter – the 940 nm source is class 1, which means the finished product does not need an eye safety label for the sensor alone when the window is in place.
Crosstalk calibration for cover glass – the parts store a calibration that subtracts the reflection from the inside of the window, which is why a flat window at 1 mm works without a light baffle.
Programmable region of interest – the VL53L1X can reduce its region of interest to a narrow beam, which turns a wide part into a spot measurement without a second order code.
Address change at run time – each sensor can be given a new I2C address after reset, so several parts share one bus behind one host port.
Dead zone stated – the minimum range is quoted with the part, because a reading inside it is not a short distance but an invalid one.
Applications
These parts are quoted for products that need to know whether something is there and how far away, typically where:
Presence and user detection – a laptop, a display or a soap dispenser wakes when a person is in front of it, and a zoned part can tell a person from a chair back at the same distance.
Level and fill sensing – a bin, a hopper or a tank is measured from above, and the reading does not depend on the colour of the contents, which matters for dark pellets and clear liquid.
Obstacle avoidance on robots and vacuums – a wide field part covers the bumper area in zones, and the short minimum range lets the robot see a wall a few millimetres from the window.
The sensor shares the board with the display, the radio and the cover glass assembly, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that board.
Sourcing and Cross-Reference
Selection starts with the geometry. The mounting height and the width of the area to cover decide the field of view, and the required accuracy decides the range: a 25 degree part at 70 cm covers a cone about 30 cm across, while a 65 degree part at 40 cm covers about 50 cm and splits it into zones. A product that needs to detect a person rather than a surface is better served by a zoned part, because per zone status lets the host ignore a wall that is always in view.
The optical and mechanical checks come next. The window has to pass 940 nm, sit at least 1 mm from the package, be flat and free of a step that bounces light from the emitter into the detector. A dark or antireflective window reduces the returned signal, and a product behind thick glass loses range in proportion. The supply needs a clean 3.3 V rail with a bulk capacitor close to the part, because the emitter draws a short pulse of current that a long trace will turn into a dip.
Where a part is replaced by a newer generation, the swap is checked on field of view, range, zone count, interface and window requirement at once, because the same 4.4 mm package can carry a different optical stack and a different calibration. The route for obsolete and last time buy parts is on our source obsolete components page, and the electrical comparison is on pin to pin cross reference. Related families are listed under sensors and detectors and amplifiers and comparators.
For volume builds, SUPERB Assembly support covers the sensor footprint, the window gap in the mechanical drawing and the supply filtering that keeps the emitter pulse off the rail.
Q: Can you quote VL53L1X and VL53L5CX, and confirm the cover glass gap and the window material that keep the range at 4 m?
A: Yes. Send the mounting height, the area to cover and the window material, and the SUPERB Tech team will confirm the part, the range at that geometry and the interface from the maker data sheet before quoting.
Why Buyers Source Time-of-Flight Sensors Through SUPERB
- Range quoted against a stated target: the maximum range is given for a white target at room light, so the figure is derated for a dark target or for sunlight before it reaches a quotation.
- Field of view matched to the geometry: the mounting height and the coverage width are checked against the cone, so a 25 degree part is not quoted for a doorway.
- Dead zone stated: the minimum range is quoted with the part, because a product that works at 20 mm needs a part whose window is not in the way.
- Window requirement given with the part: the cover glass gap, the flatness and the 940 nm transmission are quoted with the sensor, which is where most range loss comes from.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: ambient light and proximity sensors, ultrasonic transducers and distance sensors, PIR motion sensors and detectors, PIN and avalanche photodiodes.