Hall Effect Switches and Latches for Position Sensing
Product Specifications
Product Overview
A Hall effect switch turns a magnetic field into a logic level. The silicon holds a Hall plate, a chopper stabilised amplifier that removes offset and drift, a comparator with hysteresis and an output driver, so the host sees a clean edge rather than an analog voltage. In a product it replaces a mechanical limit switch, a reed contact or an optical interrupter, and it does that through plastic, so the magnet can sit inside a sealed housing and the sensor outside it.
The first choice is unipolar against omnipolar. A unipolar part responds to one pole only and stays released when the magnet is removed in the other direction, which suits a rotor where the magnet passes once per revolution. An omnipolar part responds to either pole, so the same part works whichever way the magnet is fitted, which removes an assembly error from a lid or a door. The DRV5032 family offers both, and the letters in the code carry the choice along with the threshold and the sampling rate.
The threshold is quoted as a maximum operate point, and that is the number to use. The DRV5032FA, FB and FC versions guarantee that the output changes state by 4.8 mT, with a typical value near 3 mT and a release point no higher than 3 mT, so the board has to provide 4.8 mT at the sensor under all tolerance conditions. A magnet rated at 6 mT at zero gap might deliver 3 mT at a 4 mm gap and 1.5 mT at 6 mm, which is why the air gap and the magnet grade are chosen together rather than one after the other.
Average current is set by the sampling rate, not by the supply. The DRV5032 samples the field at 5 Hz, 20 Hz or 80 Hz, sleeps between samples, and the average current follows: about 0.54 microamps for the 5 Hz FB version, about 1.3 microamps for the 20 Hz versions and about 5.2 microamps for the 80 Hz DG version, all at 1.8 V. A lid sensor that only needs to know whether the cover is closed can run at 5 Hz, while a rotor at 3,000 rpm needs the 80 Hz part or an analog latch.
Output type decides the interface. A push-pull output drives a logic pin directly and needs no resistor, which is the simplest route for a battery product. An open-drain output sinks current and needs a pull up, but it can be wired into a shared line or level shifted to a different rail, which is why the open-drain versions are used where several sensors share an interrupt. The A3144EUA-T is an open-collector part with a 25 mA sink rating, so it can drive a small relay or an LED without a transistor.
The tables below list the parts we quote most often for lid and door detection, valve position, rotor and flow sensing. Supply, threshold, current, output and package come from the maker data sheet for each order code.
Key Specifications
| Parameter | DRV5032FB | DRV5032FA | DRV5032AJ | DRV5032ZE | A3144EUA-T |
|---|---|---|---|---|---|
| Magnetic response | Omnipolar | Omnipolar | Omnipolar | Omnipolar | Unipolar, south pole |
| Supply voltage | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 3.5 V to 28 V |
| Maximum operate point | 4.8 mT | 4.8 mT | 9.5 mT | 63 mT | Not published as a maximum in the module data sheet |
| Release point | 3 mT maximum | 3 mT maximum | 7.5 mT maximum | 58 mT maximum | Below the operate point, hysteresis built in |
| Sampling rate | 5 Hz | 20 Hz | 20 Hz | 20 Hz | Continuous |
| Average current | 0.54 uA at 1.8 V | 1.3 uA at 1.8 V | 1.3 uA at 1.8 V | 1.3 uA at 1.8 V | Continuous bias, see data sheet |
| Output type | Push pull | Push pull | Open drain | Open drain | Open collector, 25 mA sink |
| Package | SOT-23, X2SON, TO-92 | SOT-23, X2SON, TO-92 | SOT-23, X2SON, TO-92 | SOT-23, X2SON, TO-92 | TO-92S |
| Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +150 C |
Included Models and Order Codes
The order codes below are the ones we quote most often. The letters after DRV5032 carry the threshold, the sampling rate and the output: FB is 5 Hz push pull, FA is 20 Hz push pull, FC is 20 Hz open drain, AJ is the 9.5 mT open drain version and ZE is the 63 mT version for a strong field. Where a figure is not published for that exact code the cell is left empty rather than copied from a sister part.
| Part Number | Magnetic response | Supply | Average current | Operate point | Output | Package |
|---|---|---|---|---|---|---|
| DRV5032FBDBZR | Omnipolar | 1.65 V to 5.5 V | 0.54 uA at 1.8 V, 5 Hz | 4.8 mT maximum | Push pull | SOT-23 |
| DRV5032FADBZR | Omnipolar | 1.65 V to 5.5 V | 1.3 uA at 1.8 V, 20 Hz | 4.8 mT maximum | Push pull | SOT-23 |
| DRV5032FCDBZR | Omnipolar | 1.65 V to 5.5 V | 1.3 uA at 1.8 V, 20 Hz | 4.8 mT maximum | Open drain | SOT-23 |
| DRV5032AJDBZR | Omnipolar | 1.65 V to 5.5 V | 1.3 uA at 1.8 V, 20 Hz | 9.5 mT maximum | Open drain | SOT-23 |
| DRV5032ZEDBZR | Omnipolar | 1.65 V to 5.5 V | 1.3 uA at 1.8 V, 20 Hz | 63 mT maximum | Open drain | SOT-23 |
| DRV5032DUDMR | Unipolar | 1.65 V to 5.5 V | 1.3 uA at 1.8 V, 20 Hz | 3.9 mT maximum | Push pull | X2SON |
| DRV5032DGLPG | Unipolar | 1.65 V to 5.5 V | 5.2 uA at 1.8 V, 80 Hz | 3.4 mT maximum | Push pull | TO-92 |
| A3144EUA-T | Unipolar | 3.5 V to 28 V | Continuous bias | Switches at the rated field, hysteresis built in | Open collector 25 mA | TO-92S |
Key Features
Threshold quoted as a maximum – the 4.8 mT figure is the worst case operate point across parts and temperature, which is the number the magnet and the air gap have to satisfy.
Sampling rate sets the current – 5 Hz samples draw 0.54 uA, 20 Hz draws 1.3 uA and 80 Hz draws 5.2 uA on the same family, so a slow lid sensor does not pay for a fast one.
Omnipolar removes an assembly error – a part that responds to either pole works whichever way the magnet is fitted, which matters on a lid or a door assembled by hand.
Open drain for shared lines – the open drain versions can share an interrupt line or sit on a different rail through a pull up, and the push pull versions need no resistor at all.
Supply from 1.65 V – the DRV5032 parts run from a single lithium cell down to 1.65 V, so the sensor can sit on the battery rail without a regulator.
Wide supply and high temperature on the TO-92 part – the A3144EUA-T runs from 3.5 V to 28 V and to +150 C, which suits a motor or a flow meter near a hot surface.
Three packages on one die – SOT-23, X2SON and TO-92 versions share the electrical specification, so a product can move from a wired assembly to a board mount without a new part.
Applications
These parts are quoted for products that need to know whether something has moved, typically where:
Lid, door and tamper detection – a magnet in the cover and a sensor on the board give a contact free state that no dust or paint can block, and the 5 Hz part keeps the average current under a microamp.
Rotor, flow and speed sensing – a magnet on a rotor produces one pulse per pass, and the 80 Hz part or the TO-92 latch keeps up with a shaft turning at a few thousand revolutions per minute.
Valve and actuator end position – an end position is read through an aluminium housing, which removes the seal and the shaft entry that a mechanical switch needs.
The switch sits on the same board as the magnet holder and the enclosure, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that board.
Sourcing and Cross-Reference
Selection starts with the field the magnet can deliver at the sensor. A 6 mm diameter magnet at a 3 mm gap gives a few millitesla, a 3 mm magnet at 6 mm gives about one, so the magnet grade, the diameter and the gap are chosen together against the maximum operate point. The second check is the sampling rate: a lid changes state a few times a day, a rotor at 3,000 rpm produces 50 edges a second, and the sampling rate has to be at least twice the edge rate.
The electrical side is the next filter. A push-pull output drives a logic pin directly and is the shortest route on a battery product; an open-drain output needs a pull up but can share a line or sit on another rail. Supply range decides whether the sensor can hang on the battery rail or needs a regulated 3.3 V, and the temperature grade decides whether a part near a motor can be used at all.
Where a part is out of stock or replaced, the swap is checked on threshold, output type, sampling rate, supply and package at once, because a part with a higher threshold will release late and a part with a lower threshold will trigger on stray fields. The route for obsolete and last time buy parts is on our source obsolete components page, and the electrical comparison is on pin to pin cross reference. Related families are listed under sensors and detectors and passive components.
For volume builds, SUPERB Assembly support covers the sensor footprint, the pull up resistor on the open drain versions and the magnet position in the housing drawing.
Q: Can you quote DRV5032FBDBZR and confirm which magnet grade gives 4.8 mT at a 4 mm gap over temperature?
A: Yes. Send the magnet grade, the air gap and the edge rate, and the SUPERB Tech team will confirm the threshold, the sampling rate and the output type from the maker data sheet before quoting.
Why Buyers Source Hall Switches Through SUPERB
- Threshold quoted as maximum, not typical: the quotation uses the worst case operate point, because a magnet chosen against a typical value will release late on some units.
- Sampling rate and current linked: the average current is quoted with the sampling rate that produces it, so a slow application is not paying for a fast sensor.
- Output type matched to the interface: push pull and open drain versions are quoted with the pull up they need, because the wrong choice shows up as a stuck interrupt line.
- Temperature grade stated: the TO-92 part reaches +150 C and the SOT-23 parts stop at +85 C, which decides whether a sensor can sit beside a motor.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Hall effect current sensors, rotary and optical encoders, magnetometer and compass sensors, solid state relays and photovoltaic drivers.