Contact Us
  • Home
  • COMPONENTS
  • LTE Cat 1 and Cat 4 Modules for Cellular Telemetry

LTE Cat 1 and Cat 4 Modules for Cellular Telemetry

Cat 4 modules carry 150 Mbps downlink for camera and gateway products, while Cat M1 and NB-IoT parts keep a link alive on a few microamps in sleep. Band coverage decides which order code ships to which market, and the regional suffix is the part of the code most often quoted wrong. The supply window is 3.3 V to 4.3 V on the Cat 4 family and 2.6 V to 4.8 V on the BG77, so one rail does not suit every part. Peak transmit current reaches close to 2 A on a Cat 4 module, which sets the bulk capacitor and the supply trace on the carrier board. Each row lists bands, data rate, supply and package, because those decide the certification route as well as the layout.
quote now

Product Specifications

Product Overview

A cellular module is the part of a connected product that carries the regulatory work. The module maker has already run the GCF, carrier and regional approvals, so a product built around a module starts its own certification from a known state instead of from a bare chipset. What the product team still owns is the antenna, the supply and the SIM interface, and those three are where most field problems appear.

The category choice is a data rate choice first. An LTE Cat 4 module such as the EC25-E or the EG25-G delivers 150 Mbps downlink and 50 Mbps uplink, which suits a gateway that uploads images or a router that shares a link. LTE Cat 1 parts sit around 10 Mbps downlink, which is enough for telemetry, firmware updates and a slow video frame, and they cost less and draw less. Cat M1 and NB-IoT parts such as the BG95-M3 go further down, to a few hundred kilobits, and trade that for a power budget measured in microamps during sleep.

Band coverage is the second decision and the one most often got wrong in a quotation. The EC25-E is built for EMEA, South Korea, Thailand and India, with LTE-FDD on B1, B3, B5, B7, B8 and B20 and LTE-TDD on B38, B40 and B41. The EG25-G covers the global band set. A unit specified for one region and shipped to another will register on nothing, and the failure looks like a hardware fault rather than a part number fault.

The supply rail follows the transmit burst. A Cat 4 module draws a peak current close to 2 A during a transmit slot, and the burst lasts about a millisecond, so the carrier board needs a bulk capacitor close to the module supply pins and a trace that does not add droop. The data sheet asks for 3.3 V to 4.3 V with 3.8 V typical on the EC25 family, and for 2.6 V to 4.8 V on the BG77, and a rail that is fine for one part is outside the window for the other.

Sleep current decides battery life, and the numbers differ by three orders of magnitude across the families. The EC25-E draws about 11 microamps in power off, 1.16 mA in sleep and about 19.5 mA idle. The BG95-M3 draws about 3.9 microamps in power saving mode and the BG77 about 3.2 microamps, which is what makes a meter that reports once a day last for years. Reading a sleep figure without its condition, which usually says USB and UART disconnected, is how a battery budget ends up optimistic.

The tables below list the parts we quote most often for telematics, metering and gateway products. Bands, data rate, supply and package come from the maker data sheet for each order code.

Key Specifications

ParameterEC25-EEG25-GBG95-M3BG77
Cellular categoryLTE Cat 4LTE Cat 4LTE Cat M1, Cat NB2, EGPRSLTE Cat M1, Cat NB2
Peak data rate150 Mbps downlink, 50 Mbps uplink150 Mbps downlink, 50 Mbps uplink588 kbps downlink, 1119 kbps uplink on Cat M1588 kbps downlink, 1119 kbps uplink on Cat M1
LTE bands, FDDB1, B3, B5, B7, B8, B20B1, B2, B3, B4, B5, B7, B8, B12, B13, B20, B25, B26, B28, B66B1, B2, B3, B4, B5, B8, B12, B13, B18, B19, B20, B25, B26, B28, B66, B85B1, B2, B3, B4, B5, B8, B12, B13, B18, B19, B20, B25, B26, B28, B66, B85
LTE bands, TDDB38, B40, B41B38, B40, B41Not applicable on this codeNot applicable on this code
FallbackWCDMA B1, B5, B8 and GSM, EDGE B3, B8WCDMA and GSM, EDGE on the global band setEGPRS 850, 900, 1800, 1900 MHzNone, LTE only
Supply voltage3.3 V to 4.3 V, 3.8 V typical3.3 V to 4.3 V, 3.8 V typical3.3 V to 4.3 V, 3.8 V typical2.6 V to 4.8 V, 3.3 V typical
Sleep current11 uA power off, 1.16 mA sleep11 uA power off, 1.16 mA sleep3.9 uA in power saving mode3.2 uA in power saving mode
Operating temperature-35 C to +75 C, extended -40 C to +85 C-35 C to +75 C, extended -40 C to +85 CExtended range on the series data sheetExtended range on the series data sheet
Host interfaceUSB 2.0, 2 UART, PCM, I2C, SDIOUSB 2.0, 2 UART, PCM, I2C, SDIOUSB, UART, PCM, I2C, ADC, GPIOUSB, UART, I2C, PCM, ADC, GPIO
PackageLCC, 29.0 x 32.0 x 2.4 mmLCC, 29.0 x 32.0 x 2.4 mm68 pad LGA94 pad LGA, 14.9 x 12.9 x 1.7 mm

Included Models and Order Codes

The order codes below are the ones we quote most often. The regional suffix is part of the code, not a packaging option: an E code, a G code and an AU code carry different band sets, and the certification list changes with them. Where a number is not published for that exact code the cell is left empty rather than filled from a neighbouring variant.

Part NumberCategoryRegions and bandsPeak rateSupplyPackage
EC25-ELTE Cat 4EMEA, South Korea, Thailand, India: FDD B1, B3, B5, B7, B8, B20150 / 50 Mbps3.3 V to 4.3 VLCC 29.0 x 32.0 x 2.4 mm
EC25-EULTE Cat 4EMEA: FDD B1, B3, B7, B8, B20, B28A150 / 50 Mbps3.3 V to 4.3 VLCC 29.0 x 32.0 x 2.4 mm
EC25-EUXLTE Cat 4EMEA with B28A: FDD B1, B3, B7, B8, B20, B28A150 / 50 Mbps3.3 V to 4.3 VLCC 29.0 x 32.0 x 2.4 mm
EC25-EMLTE Cat 4EMEA and Southeast Asia: FDD B1, B3, B5, B7, B8, B20, B28150 / 50 Mbps3.3 V to 4.3 VLCC 29.0 x 32.0 x 2.4 mm
EG25-GLTE Cat 4Global band set: FDD B1 to B28 and B66, TDD B38, B40, B41150 / 50 Mbps3.3 V to 4.3 VLCC 29.0 x 32.0 x 2.4 mm
BG95-M2Cat M1, Cat NB2, EGPRSGlobal: FDD B1 to B28 and B66, EGPRS quad band588 / 1119 kbps on Cat M12.6 V to 4.8 V68 pad LGA
BG95-M3Cat M1, Cat NB2, EGPRSGlobal: FDD B1 to B28, B66, B85, EGPRS quad band588 / 1119 kbps on Cat M13.3 V to 4.3 V68 pad LGA
BG77Cat M1, Cat NB2Global: FDD B1 to B28, B66, B85588 / 1119 kbps on Cat M12.6 V to 4.8 V94 pad LGA 14.9 x 12.9 x 1.7 mm

Key Features

Category matched to the payload – a camera gateway needs Cat 4 for 150 Mbps, a meter needs Cat M1 for microamp sleep, and quoting either part for the other use case costs money in both directions.

Bands stated per order code – the regional suffix carries the band set, so the quote names the code that matches the country of deployment rather than the family.

Transmit burst allowance called out – the peak current of a Cat 4 module is close to 2 A for about a millisecond, which sets the bulk capacitor and the supply trace on the carrier board.

Sleep current quoted with its condition – the microamp figures on the BG95 and BG77 are quoted with USB and UART disconnected, which is the condition a battery product has to reproduce.

One footprint across categories – the BG95 and the Cat M1 and Cat NB parts share an LGA footprint across the family, so a product can change category without a new board.

GNSS available inside the module – the EC25 family offers optional GNSS and the BG95 series integrates it, which removes a second receiver on a tracker that already needs a position.

Certification list quoted with the part – GCF, CE, UKCA, KC, RCM and the carrier approvals differ by suffix, and that list decides how much of the product certification is already covered.

Applications

These modules are quoted for products that need a wide area link rather than a local one, typically where:

Telematics and fleet units – a vehicle unit reports position and diagnostics, and it needs a part that survives the temperature under a dashboard and keeps a link in a weak cell.

Metering and remote sensing – a water or gas meter reports once a day and sleeps in between, so the microamp figure on Cat M1 and NB-IoT matters more than the data rate.

Gateways and camera backhaul – a gateway that uploads images or shares a link needs the 150 Mbps downlink of a Cat 4 part and the fallback to WCDMA or GSM where LTE coverage ends.

The module sits on a carrier board with the SIM interface, the antenna feed and the power stage, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that board.

Sourcing and Cross-Reference

Selection starts with the payload and the power budget, not with the family name. A product that sends a few hundred bytes a day wants Cat M1 or NB-IoT, because the sleep current dominates the average draw and the peak current is modest. A product that sends images or serves a local network wants Cat 4, because the transmit time sets the energy per message, and a faster link finishes the burst sooner even though the peak current is higher.

The second check is the band set against the country of deployment. A regional code is cheaper and better matched to the operator approvals in its region, and a global code costs more but removes the stocking problem when the same product ships to several markets. The third check is the carrier board: the supply window, the bulk capacitor at the module pins, the SIM or eSIM arrangement and the antenna keep out all come from the module data sheet, and all differ between the Cat 4 LCC parts and the small LGA parts.

Where a module has been replaced by a newer category, the swap is checked on footprint, supply, band set, command set and certification at once, because a part that registers but reports a different band set will fail certification rather than the bench test. The route for obsolete and last time buy parts is on our source obsolete components page, and module level alternatives are listed under multi function ICs and MCU and embedded processors.

For volume builds, SUPERB Assembly support covers the module footprint, the bulk capacitors at the supply pins and the shielding around the radio section.

Q: Can you confirm which EC25 suffix covers B20 and B28 together, and quote the 3.8 V rail parts needed for the transmit burst?

A: Yes. Send the deployment country, the payload size and the supply rail, and the SUPERB Tech team will confirm the band set, the peak current and the certification list from the maker data sheet before quoting.

Why Buyers Source Cellular Modules Through SUPERB

  1. Region and band set confirmed, not assumed: the suffix on the order code is checked against the country of deployment, because a wrong band set looks like a hardware fault in the field.
  2. Supply and burst current quoted together: the rail window and the bulk capacitance are quoted with the module, so the carrier board is not built around the wrong peak current.
  3. Category matched to the sleep budget: Cat 4, Cat 1, Cat M1 and NB-IoT parts are compared on sleep current and energy per message, not only on headline data rate.
  4. Certification status given with the quote: the approvals that come with the module are listed, so the product certification plan starts from what is already covered.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: GNSS receiver modules for positioning, USB Type C and power delivery controllers, step down DC DC converter chips, Bluetooth low energy SoCs.