RF Detector Diodes and Zero-Bias Schottky Detectors
Product Specifications
Product Overview
A detector diode turns a small RF voltage into a DC or video voltage, and it does that best in the square law region, which for most of these parts means input power below about minus 20 dBm. Above that the output follows the peak of the waveform rather than its power, the response flattens, and a power meter built around the part needs a correction table. That transition, not the maximum frequency, is what separates one detector diode from another in a level control loop.
The barrier height decides whether the diode needs bias. A low barrier part such as the HSMS-2850, the SMS7630 or the BAT15-099 conducts at a few tens of millivolts and works at zero bias, so there is no bias resistor to inject noise and no bias supply to drift. The price is a low reverse breakdown, 2 V on the HSMS-2850 family and 4 V on the BAT15-099, which means a detector built with them needs a limiter or a coupler in front of it. The medium barrier parts, HSMS-2820 at 340 mV of forward drop and HSMS-2800 at 400 mV, tolerate 15 V and 70 V respectively and are biased at a few microamps when the detector has to hold its calibration over temperature.
Junction capacitance sets the upper frequency, and it is the number that gets ignored. The SMS7630-061 is quoted at 0.3 pF at 0.15 V and is used above 26 GHz in a 0201 footprint; the HSMS-2850 sits at 0.3 pF at 1 V in SOT-23; the HSMS-2820 is 1.0 pF and the HSMS-2800 is 2.0 pF, which keeps them comfortable below 4 GHz and poor above 12 GHz. On a 50 ohm line a 1 pF shunt capacitance is already several ohms of reactance at 10 GHz, so the matching network, not the diode, becomes the limit.
Video bandwidth is set by the load resistor against that junction capacitance, and a detector built for a fast envelope (pulse radar, a switching transmitter) needs a low video resistance, which is why the HSMS-2820 quotes 12 ohms while the zero bias parts run into kilohms and are used for slow level monitoring. Both figures matter when a part is replaced: a swap that matches capacitance but triples the video resistance will still read the average power correctly and will still miss a 1 microsecond pulse.
Key Specifications
Values are the data sheet maxima unless marked typical. Capacitance is measured at 1 MHz, forward voltage at 1 mA except where another current is stated, and dynamic resistance at 5 mA.
| Parameter | HSMS-2800 | HSMS-2820 | HSMS-2850 | SMS7630-061 | BAT15-099 | 1N5711 |
|---|---|---|---|---|---|---|
| Breakdown voltage | 70 V | 15 V | 2 V | not quoted | 4 V | 70 V |
| Forward voltage | 400 mV | 340 mV | not quoted | 60 to 120 mV at 0.1 mA | 250 mV | 400 mV |
| Junction capacitance | 2.0 pF | 1.0 pF | 0.3 pF at 1 V | 0.3 pF at 0.15 V | 0.29 pF typical | 2.0 pF |
| Dynamic resistance | 35 ohm | 12 ohm | not quoted | not quoted | 5.8 ohm | not quoted |
| Bias required | yes, a few microamps | yes, a few microamps | none | none | none | yes |
| Package | SOT-23 | SOT-23 | SOT-23 | 0201 | SOT-143 | DO-35 axial |
Included Models and Order Codes
The suffix after the family number is the configuration inside the package, and it matters: a series pair doubles the detected voltage at the cost of doubling the video resistance, and a quad is used for a balanced or a temperature compensated detector.
| Part Number | Configuration | Breakdown | Capacitance | Package |
|---|---|---|---|---|
| HSMS-2800 | single | 70 V | 2.0 pF | SOT-23 |
| HSMS-2803 | common anode pair | 70 V | 2.0 pF | SOT-23 |
| HSMS-2804 | common cathode pair | 70 V | 2.0 pF | SOT-23 |
| HSMS-2820 | single | 15 V | 1.0 pF | SOT-23 |
| HSMS-2822 | series pair | 15 V | 1.0 pF | SOT-23 |
| HSMS-2823 | common anode pair | 15 V | 1.0 pF | SOT-23 |
| HSMS-2824 | common cathode pair | 15 V | 1.0 pF | SOT-23 |
| HSMS-2825 | unconnected pair | 15 V | 1.0 pF | SOT-143 |
| HSMS-2827 | ring quad | 15 V | 1.0 pF | SOT-143 |
| HSMS-2850 | single, zero bias | 2 V | 0.3 pF at 1 V | SOT-23 |
| HSMS-2852 | series pair, zero bias | 2 V | 0.3 pF at 1 V | SOT-23 |
| HSMS-2855 | unconnected pair, zero bias | 2 V | 0.3 pF at 1 V | SOT-143 |
| SMS7630-061 | single, zero bias | not quoted | 0.3 pF at 0.15 V | 0201 |
| BAT15-099 | single, low barrier | 4 V | 0.29 pF typical | SOT-143 |
| 1N5711 | single axial | 70 V | 2.0 pF | DO-35 |
Two notes on supply status. The SMS7630-061 is marked not recommended for new work by the maker, so it is quoted with a last time buy option and a smaller footprint alternative. The HSMS-2850 series and the 1N5711 are long lived but move between packaging options, which changes the order code without changing the die.
Key Features
Zero bias operation on the low barrier parts – the HSMS-2850, SMS7630 and BAT15-099 conduct at a few tens of millivolts, so the detector needs no bias supply and no bias resistor noise in the video amplifier.
Capacitance quoted at the working voltage – 0.3 pF at 0.15 V on the 0201 part and 0.3 pF at 1 V on the SOT-23 part, which is the figure that decides whether the detector still works at 24 GHz.
Video resistance given with the part – 12 ohms on the HSMS-2820 and 35 ohms on the HSMS-2800, so the video bandwidth of an envelope detector can be calculated before the board is laid out.
Single, pair and quad configurations – the same die is offered as a single, a series pair for more output voltage and a quad for a balanced detector that cancels the temperature drift of two junctions.
Breakdown voltage spread across the family – 2 V on the zero bias parts and 70 V on the HSMS-2800 and 1N5711, which is the range between a receiver input that needs a limiter and a transmitter sample port that does not.
Axial and surface mount versions of the same function – the 1N5711 in DO-35 for a repair or a legacy instrument and the SOT-23 parts for a new board, so an old detector can be kept in service without a layout change.
Applications
These diodes are quoted for products that need to know how much RF is present, typically where:
Transmitter power monitoring – a coupled sample is rectified and fed to a control loop or a meter, and the detector has to hold its reading from minus 20 to 70 C, which is where a biased medium barrier part is easier to compensate than a zero bias one.
Receiver level detection and RSSI – a low barrier part at the input of a receiver produces a DC level proportional to signal power in the square law region, and that level drives an AGC loop long before the signal reaches the analogue to digital converter.
Test instruments and radar front ends – power sensors, standing wave ratio bridges and pulse detectors need a defined video bandwidth, and the video resistance of the diode sets how short a pulse the instrument can still resolve.
A detector sits at the end of a chain that starts at a coupler or a limiter and ends at an operational amplifier, so the diode is usually quoted with the board it lands on. That chain is what we build as the SUPERB PCB and the SUPERB PCBA, which is why the coupling factor, the video load and the diode capacitance are checked together rather than one part at a time.
Sourcing and Cross-Reference
Replacement starts with the barrier height, because a zero bias part cannot be swapped for a biased part without changing the bias network, and a biased part swapped for a zero bias one loses sensitivity at low power. The second check is capacitance at the working voltage: 0.3 pF against 1.0 pF is the difference between a detector that works at 18 GHz and one that works at 6 GHz, whatever the data sheet headline says about frequency.
The third check is the video load. A part with 12 ohms of dynamic resistance drives a 50 ohm video amplifier directly, while a part with several kilohms needs a high impedance buffer and will not reproduce a short pulse. The comparison method we apply to these swaps is described on obsolete RF part replacement, and the wider supply route for this category is on RF component sourcing.
Supply is the last check. Detector diodes are made in small wafers and the low barrier families have been trimmed more than once, so a scheduled last time buy is normal for a product with a long service life. For volume builds, SUPERB Assembly support covers the coupler, the limiter and the video amplifier around the diode, and the parts that share the board are listed under RF mixers and IQ modulators, RF switches and PIN diode switches and RF gain blocks and low noise amplifiers.
Q: Can you supply a pin to pin replacement for the HSMS-2850 and the HSMS-2852?
A: Yes. The SUPERB Tech team checks barrier height, capacitance, video resistance and the package footprint against the maker data sheet, and states which of those figures move. A part that matches two of the four is not quoted as a drop in replacement.
Q: What does tangential signal sensitivity mean on these data sheets?
A: It is the input power at which the detected pulse raises the noise by an amount equal to the average noise level, so it sits about 4 dB above the smallest signal the detector can see. It is the figure to compare between two low barrier diodes, not the forward voltage.
Q: Do you hold the quad and the pair configurations, or only the single?
A: Single, series pair, common anode, common cathode and quad versions are quoted from the same families, and the configuration is confirmed per order code because the pair and quad parts are on a separate schedule from the singles.
Why Buyers Source Detector Diodes Through SUPERB
- Barrier height checked before a swap: a zero bias part is never offered as a replacement for a biased one without saying so, because the bias network changes with it.
- Capacitance at the working voltage: the figure is quoted with its test voltage, since 0.3 pF at 0.15 V and 1.0 pF at 1 V lead to completely different upper frequency limits.
- Video resistance stated for pulse work: the dynamic resistance is given with the part so a pulse detector is not built around a diode that cannot follow the pulse.
- Long lived parts held with a last time buy: small wafer families are quoted with a dated replacement or a buffer quantity, which keeps a repair line and a legacy instrument in service.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with PIN and avalanche photodiodes, RF mixers and IQ modulators, RF isolators and circulators and the sensors and detectors column.