Contact Us
  • Home
  • COMPONENTS
  • Piezo Buzzers and Magnetic Audio Indicators for Alerts

Piezo Buzzers and Magnetic Audio Indicators for Alerts

A transducer needs a square wave from the host, an indicator only needs a DC voltage. Piezo parts run at 3 V to 220 V with currents under 20 mA and reach the highest sound pressure in a thin package. Magnetic indicators run from 3 V to 12 V at about 30 mA and give a steady tone with a narrow frequency tolerance. Every sound pressure figure is quoted at 10 cm with the drive condition, because the distance and the voltage change the number.
quote now

Product Specifications

Product Overview

Two things decide which buzzer fits a product, and they are usually confused. The first is the technology: a piezo disc is a capacitor that flexes when a voltage is applied, so it is a voltage driven part with a low current, while a magnetic buzzer is a coil and a ferromagnetic disc, so it is a current driven part that works from a lower voltage and draws an order of magnitude more current. The second is whether the drive circuit is inside the part. A transducer has no oscillator, so the host has to supply a square wave at the resonant frequency. An indicator has the oscillator built in, so a DC voltage produces a fixed tone and the host only has to switch a pin.

That second difference is where most order errors come from. The PKMCS0909E4000-R1 is an external drive sounder: with a 4.0 kHz square wave at plus or minus 1.5 V peak it produces 72 dB typical at 10 cm, and it will produce nothing at all from a steady 3 V. The CMI-1295IC-0385T is the opposite: it is internally driven, so 3 V DC produces a 2,400 Hz tone at 85 dB at 10 cm and the only thing the firmware does is turn the pin on and off. A part chosen across that line will appear to be dead on the bench even though it is working as specified.

Sound pressure is quoted at 10 cm in almost every data sheet we work from, and that distance is part of the number. Sound pressure falls by 6 dB for every doubling of distance, so a part quoted at 85 dB at 10 cm gives about 79 dB at 20 cm and about 73 dB at 40 cm. A specification that says 85 dB without a distance is not usable for a product, and a comparison between two parts on different distances will pick the wrong one. The drive voltage matters as much: a piezo sounder quoted at plus or minus 1.5 V peak gives more output at plus or minus 12.5 V peak, up to its maximum rating, and a magnetic indicator is quoted at its rated voltage with a tolerance band around it.

The mechanical side decides whether the tone survives the enclosure. A piezo disc needs a free air path and a cavity in front of it, and the cavity resonates with the disc, which is why the same part can be 6 dB louder or quieter in two housings. A magnetic indicator has a port at the top and a gasket that must not be compressed over the port. Sealing a buzzer to meet a water ingress rating usually costs several dB, and that loss has to be inside the budget rather than discovered after the first enclosure sample.

The table below covers the parts we quote most often: the thin SMD piezo sounders for handheld and instrument front panels, and the magnetic indicators with a built in drive circuit for alarms and appliance panels. Sound pressure at 10 cm, rated frequency, voltage range, current and package come from the maker data sheet for each order code.

Key Specifications

ParameterSMD piezo sounder, PKMCS0909E4000-R1Magnetic indicator, CMI-1295IC-0385TPiezo indicator with circuit, CPI-2622-12TH
DriveExternal, host supplies the square waveInternal oscillator, DC inputInternal oscillator, DC input
Sound pressure at 10 cm72 dB typical, 65 dB minimum85 dB100 dB
Measurement conditionPlus or minus 1.5 V peak, 4.0 kHz square waveAt the 3 V rated voltageAt the 12 V rated voltage
Rated frequency4.0 kHz2,400 Hz plus or minus 100 Hz2,800 Hz
VoltagePlus or minus 12.5 V peak maximum2 V to 5 V, 3 V rated12 V rated
CurrentBelow 20 mA class30 mA maximum50 mA
Package9.0 x 9.0 x 1.9 mm SMD12 x 12 x 9.5 mm through hole26.1 x 26.1 x 22.1 mm through hole
Temperature-40 C to +85 C-30 C to +70 C-20 C to +60 C
Mounting noteReflowable, needs a cavity in front of the discWashable, port at the topThrough hole, panel or board mount

Included Models and Order Codes

The table lists the order codes we quote most often for alerts, key feedback and appliance panels. Sound pressure at 10 cm, rated frequency, voltage range, current and package come from the maker data sheet for that code. The letters IC in a CUI code mean an internal drive circuit, so a part with IC in the name is an indicator and a part without it is a transducer.

Part NumberTypeDriveSound pressureFrequencyVoltagePackage
PKMCS0909E4000-R1Piezo sounderExternal72 dB typical at 10 cm4.0 kHzPlus or minus 12.5 V peak max9.0 x 9.0 x 1.9 mm SMD
PKLCS1212E4001-R1Piezo sounderExternal84 dB typical at 10 cm4.0 kHzPlus or minus 12.5 V peak max12 x 12 x 3.0 mm SMD
CPI-1375IC-80TPiezo indicatorInternal88 dB at 10 cm4,000 Hz12 V DC13.8 x 13.8 x 7.5 mm
CPI-2622-12THPiezo indicatorInternal100 dB at 10 cm2,800 Hz12 V DC, 50 mA26.1 x 26.1 x 22.1 mm
CMI-9605IC-0380TMagnetic indicatorInternal80 dB at 10 cm2,700 Hz3 V DC, 30 mA9.6 x 9.6 x 5 mm
CMI-1295IC-0385TMagnetic indicatorInternal85 dB at 10 cm2,400 Hz3 V DC, 2 V to 5 V range12 x 12 x 9.5 mm
CMI-1295IC-0585TMagnetic indicatorInternal85 dB at 10 cm2,400 Hz5 V DC, 30 mA12 x 12 x 9.5 mm
CMI-1295IC-1285TMagnetic indicatorInternal85 dB at 10 cm2,400 Hz12 V DC, 30 mA12 x 12 x 9.5 mm
CMI-1210-90-SMT-TRMagnetic indicatorInternal90 dB at 10 cm2,400 Hz5 V DC, 30 mA12.8 x 12.8 x 10 mm SMD
CMI-1271-85-SMT-TRMagnetic indicatorInternal85 dB at 10 cm2,400 Hz12 V DC, 30 mA12.8 x 12.8 x 7.1 mm SMD

Key Features

Transducer or indicator named on every line – the drive column says whether the host has to supply a square wave or a DC level, which is the difference between a working alert and a silent board.

Sound pressure with its distance and drive – 72 dB at 10 cm at plus or minus 1.5 V peak is a complete statement, and 85 dB on its own is not, so the condition is carried with the figure.

Tight frequency tolerance on indicators – the internally driven magnetic parts hold 2,400 Hz plus or minus 100 Hz, so the tone does not shift with supply voltage or temperature.

Thin SMD piezo for handheld products – the 9.0 x 9.0 x 1.9 mm sounder is reflowable and fits behind a display frame, which is where a 12 mm through hole part will not go.

Current budget visible at a glance – a piezo part draws a few milliamps while a magnetic indicator draws 30 mA, and that difference decides whether the alert runs from a coin cell or a rail.

Washable and ported options – the through hole magnetic parts are washable with the port at the top, which suits a board that goes through an aqueous clean before the enclosure is closed.

Applications

These parts are quoted for products that have to make themselves heard, typically where:

Appliance and instrument panels – a magnetic indicator with a built in circuit gives a key beep or an end of cycle tone from a single pin, with the tone frequency fixed by the part rather than by the firmware.

Medical and security devices – an indicator with a narrow frequency tolerance keeps the alarm tone identical between units, which matters when the sound is part of the product's approval.

Handheld and battery products – a thin piezo sounder driven by a bridge output from the host draws little current and fits behind a sealed membrane, and the host can also vary the frequency for a multi tone alert.

The buzzer sits on the same front panel board as the switches and the driver transistor, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that assembly.

Sourcing and Cross-Reference

Selection starts with the drive the board can provide. If the host already has a spare timer output and a bridge or a transistor pair, a transducer is the cheaper and louder option per millimetre. If the pin count and the firmware are fixed, an indicator removes the oscillator from the firmware and the tone is set by the part.

The second check is the acoustic path. The cavity in front of the disc, the port diameter and the gasket all change the output by several dB, and a sealed enclosure loses more. The distance used in the specification has to match the distance the user will be from the product, and a part quoted at 10 cm for a product that is worn on a belt is not the same requirement as one quoted at 1 m for a wall mounted alarm.

Where a code is short or has been replaced, the substitute is checked on drive type, sound pressure at the same distance, rated frequency, voltage range, current and package at once. A part that matches the sound pressure but needs a square wave where the board has only a DC pin will not work, and a part that matches the tone but is 3 mm taller may not fit under the cover. The route for that comparison is on our source obsolete components page, and the mechanical check is on pin to pin cross reference.

For volume builds, SUPERB Assembly support covers the acoustic port in the housing, the gasket compression and the drive transistor or bridge that the sounder needs.

Q: Can you confirm which of these needs a square wave from the host, and quote a 3 V indicator with the same 12 mm footprint?

A: Yes. Send the supply rail, the distance the alert has to be heard at and the space behind the panel, and the SUPERB Tech team will confirm the drive type, the sound pressure and the package from the maker data sheet before quoting.

Why Buyers Source Buzzers Through SUPERB

  1. Drive type stated before price: a transducer and an indicator are never quoted as interchangeable, because the difference is in the firmware and the pin count, not in the datasheet headline.
  2. Sound pressure with distance and voltage: every figure is given at 10 cm with the drive condition, so a comparison between two parts is made on the same basis.
  3. Current shown against the rail: 30 mA on a magnetic part and a few milliamps on a piezo part decide whether the alert can run from the standby rail.
  4. Package and port given together: the height, the port position and the washable rating are quoted with the part, because the enclosure drawing needs all three.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Passive components, MEMS microphones, MLCC and ceramic capacitors, Constant current LED drivers, Sourcing obsolete components, Component lead time solutions, BOM shortage recovery.