Contact Us
  • Home
  • COMPONENTS
  • PIN Diode Limiters for RF Receiver Front End Protection

PIN Diode Limiters for RF Receiver Front End Protection

A PIN limiter is a passive part that turns a receiver input into a short when the signal is too large, and it needs no supply to do that. Threshold levels on this page run from 10 dBm to 37 dBm, and continuous input ratings from 36 dBm to 44 dBm. The choice between them is set by the largest signal the antenna can deliver and by the insertion loss the receiver can afford. Each row lists threshold, CW and peak ratings, junction capacitance and series resistance.
quote now

Product Specifications

Product Overview

A receiver front end has to survive a signal that is far larger than the one it is meant to hear. The classic case is a radar or a jammer close to the antenna, where the input can reach several watts for a short pulse, and the low noise amplifier behind the connector has a damage level measured in milliwatts. A PIN limiter sits between the two and does nothing at all until the signal passes a threshold, and then it becomes a low impedance that reflects the excess.

The mechanism is the stored charge in the intrinsic layer. At low signal levels the layer is depleted, the diode looks like a small capacitor and the insertion loss is a tenth of a dB. Above the threshold, the RF current forward biases the junction on the positive half cycle, charge builds up in the intrinsic layer and the diode stops behaving like a capacitor. The thicker the intrinsic layer, the higher the threshold and the more power the part can handle, which is why the family is offered in steps.

The Skyworks CLA series on this page shows that trade off clearly. The CLA4601 has a 1.0 micron intrinsic layer, a 12 dBm threshold, a 36 dBm continuous rating and 0.37 pF, which makes it a clean up stage behind a coarser part. The CLA4609 has a 28 micron layer, a 37 dBm threshold and a 44 dBm continuous rating, which is a coarse stage that faces the antenna. A typical chain puts the coarse part first, closest to the antenna, and the fine part second, and the order matters: reversing it exposes the small part to the full incident power.

Two numbers are often missed. Recovery time is the delay before the diode returns to its low loss state after the pulse, and during that window the receiver is deaf, so a radar with a short pulse repetition interval can lose returns. Spike leakage is the energy that gets through before the diode turns on, and it is the figure that decides whether the amplifier behind survives even when the limiter itself does.

The limiter is a shunt element with a DC return, and the layout is part of the part. A 22 nH ground return and a DC block of 100 pF are the conditions the published power figures are measured under, so a board that uses a long narrow ground path will not reach them. Thermal path matters too, because the continuous rating is quoted at a 25 C heat sink and derates linearly to zero at 175 C.

Key Specifications

ParameterValue range on this pageNotes
Threshold level, 1 dB loss point10 dBm to 37 dBmMeasured at 2.6 GHz, 25 C
Maximum continuous input36 dBm to 44 dBm25 C heat sink, derate to 0 W at 175 C
Maximum pulsed input57 dBm to 74 dBm1 microsecond pulse, 0.1 percent duty
Insertion loss at -10 dBm0.1 dB to 0.3 dB10 GHz, 5 GHz for the largest part
Junction capacitance at 0 V0.35 pF to 0.85 pFMeasured at 1 MHz
Series resistance at 10 mA1.0 ohm to 20 ohmMeasured at 500 MHz
Intrinsic layer thickness1.0 micron to 28 micronSets threshold and power handling
Recovery time5 ns to 50 nsDepends on part and drive
Carrier lifetime5 ns to 1000 nsTypical at 10 mA
Thermal impedance, average40 to 1175 C per WInfinite heat sink
ConfigurationShunt diode with DC returnPublished figures assume 22 nH return and 100 pF block

Included Models and Order Codes

The table gives the maker figures for the packaged parts, which is the form used on a board. Threshold and power columns are the ones to compare first: a part with a low threshold protects sooner and adds loss earlier, and a part with a high threshold survives more incident power but lets more through before it acts.

Part NumberThreshold, 1 dB pointMax CW inputMax peak inputCapacitance at 0 VSeries resistance at 10 mAInsertion loss
CLA4601-00012 dBm36 dBm65 dBm0.37 pF1.0 ohm0.1 dB
CLA4603-00010 dBm38 dBm67 dBm0.45 pF1.5 ohm0.1 dB
CLA4605-00011 dBm40 dBm70 dBm0.45 pF2.0 ohm0.1 dB
CLA4606-00011 dBm41 dBm71 dBm0.40 pF2.5 ohm0.1 dB
CLA4606-085LF12 dBm nominal, 5 W saturatedNot published as a single figureNot published as a single figure0.30 pFNot publishedNot published
CLA4607-00026 dBm43 dBm73 dBm0.45 pF7.0 ohm0.1 dB
CLA4608-00023 dBm43 dBm73 dBm0.85 pF7.0 ohm0.2 dB
CLA4609-00037 dBm44 dBm74 dBm0.51 pF20 ohm0.3 dB
CLA4610-00022 dBm40 dBm57 dBm0.38 pF4.5 ohm0.1 dB
CLA4611-00025 dBm40 dBm64 dBm0.35 pF12 ohm0.3 dB
MADP-011027-14150TPIN element, 100 V, 250 mANot publishedNot published0.35 pF at 50 VNot publishedNot published

Key Features

Passive protection – The diode needs no bias supply, so a receiver keeps its protection when the board is unpowered, which is the state a unit spends most of its life in.

Threshold in 10 steps – From 10 dBm to 37 dBm, so a stage can be chosen for the incident power at its own point in the chain instead of at the connector.

Continuous ratings to 44 dBm – The largest parts on this page hold 25 W continuously at a 25 C heat sink, which covers a transmitter sharing the same antenna through a circulator.

Low capacitance parts – 0.35 pF to 0.45 pF parts keep the limiter transparent to a wideband front end up to and beyond 10 GHz.

Recovery in nanoseconds – Recovery times from 5 ns let a pulse radar keep its short range returns instead of losing them in the limiter tail.

Published layout conditions – Power figures are given with the DC return and blocking capacitor that produced them, so a board can be checked against the same conditions.

Applications

Limiters belong wherever a sensitive amplifier shares an antenna with a strong transmitter or sits in a strong field.

Radar and electronic warfare front ends – A two stage limiter with a coarse part at the antenna and a fine part before the amplifier holds the input inside the amplifier damage level during a transmit pulse.

Test and measurement inputs – An instrument input that may be connected to a live transmitter is protected by a low threshold part, and the 0.1 dB insertion loss keeps the measurement honest.

Shared antenna radios – A duplexed radio that transmits and receives on the same port uses a limiter behind the circulator, so leakage during transmit does not reach the low noise amplifier.

Limiter stages are quoted with the SUPERB PCB and the SUPERB PCBA build in view, because the ground return and the thermal path are board decisions that the part cannot fix.

Sourcing and Cross-Reference

Limiter diodes are a small catalogue and shortages are common on the high power end. When a 44 dBm part is not available, a two stage arrangement of lower power parts can cover the same incident level, provided the first stage survives the spike and the second stage is not exposed to the full power. We quote the pair with the calculated power at each stage, not just two part numbers.

Die and packaged parts are not interchangeable in a build. The published power figures for die are taken on a 0.5 oz copper board with a bond wire of 0.8 mil, and the same die in a plastic package carries slightly different capacitance and thermal numbers. We state which form the quote refers to, because a part change between them needs the layout checked.

Obsolete limiter part numbers appear often, since several makers have consolidated their PIN lines. Send the threshold and the continuous rating the board needs, and the substitute is chosen on those two figures plus the package, rather than on a name that happens to look similar.

SUPERB Assembly fits the limiter and the amplifier in the same pass, so the power at each stage is measured on the first article rather than assumed from the data sheet.

Q: Can you supply a limiter that holds a higher continuous input than the part currently on the drawing?

A: Threshold and continuous input decide it; the SUPERB Tech desk quotes the single part and the two stage pair with the power at each stage worked out.

Why Buy RF Limiter Diodes Through SUPERB

  1. Ratings compared, not names: Quotes list threshold, continuous and peak input side by side, so a replacement is chosen on the figure that matters.
  2. Two stage options: Where a single high power part is not available, we quote a pair with the power at each stage worked out.
  3. Package stated: Die and packaged forms are quoted separately, because the capacitance and thermal path differ between them.
  4. Layout conditions supplied: The DC return and blocking values behind the published figures come with the quote, which is what the board check needs.
  5. Board and assembly in one place: The limiter and the low noise amplifier are quoted together, so the protection level is checked against the amplifier damage figure.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: RF Detector Diodes and Zero Bias Schottky Detectors, RF Switches and PIN Diode Switches, GaN HEMT RF Power Transistors, RF Isolators and Circulators.