Contact Us

Fully Differential Amplifiers and ADC Drivers

A fully differential amplifier converts a single ended signal into a balanced pair and sets the output common mode to match the ADC reference. Bandwidth runs from 145 MHz on the precision parts to 8 GHz on the RF front end driver, and the choice follows the sampling rate and the resolution. Input noise of 1.1 nV per root hertz to 5 nV per root hertz sets the resolution floor once the source impedance is known. Supply range of 2.7 V to 5.4 V on the precision parts and 3 V to plus or minus 5 V on the current feedback parts decides the headroom. Each row lists bandwidth, slew rate, noise, supply and package, because those four decide whether an 18 bit ADC keeps its last two bits.
quote now

Product Specifications

Product Overview

A fully differential amplifier takes one signal, or a differential pair, and drives a balanced output whose average voltage is set by a separate input. That last part is what makes it an ADC driver: the converter needs its input centred on a reference, usually half of its supply or its internal reference, and the amplifier's common mode pin is driven from that reference so the two move together. Without that loop the converter loses codes at the top and bottom of its range, and the loss shows up as distortion rather than as an offset.

The precision parts are chosen for the last two bits of a high resolution converter. The THS4551 is specified with a 150 MHz bandwidth, 220 volts per microsecond slew rate, 3.3 nanovolts per root hertz of input noise and 175 microvolts of maximum offset, on a supply from 2.7 V to 5.4 V at 1.37 mA. That offset and drift matter because a 24 bit converter with a 2.5 V reference resolves about 0.15 microvolts per code, so an amplifier with millivolt offset needs the offset removed in firmware or in a calibration step.

The high speed parts are chosen for the sampling clock. The ADA4932-1 reaches 560 MHz at unity gain with a 2800 volts per microsecond slew rate and 3.6 nanovolts of noise while drawing 9.6 mA, and the AD8138 reaches 320 MHz with 1150 volts per microsecond. Both run from a single 3 V rail up to plus and minus 5 V, which lets the same part drive a 5 V converter or a bipolar front end. Above that, the LMH5401 offers an 8 GHz gain bandwidth product and the LTC6409 a 10 GHz product, and those parts are used where the converter samples at hundreds of megasamples per second.

Noise budgeting is the step that decides between them. The amplifier noise appears at the input, so it is compared with the source impedance and the converter noise: a 1 kilohm source with a 4 nanovolt amplifier is dominated by the resistor, and a 50 ohm source with an 18 bit converter is dominated by the amplifier. The feedback resistor network adds noise in proportion to its value, which is why the data sheets specify distortion and noise with a particular resistor value and why a lower resistor value improves both.

Stability and layout follow from the same numbers. A fully differential amplifier drives a switched capacitor load, so the output needs a small series resistor and a differential capacitor to keep the loop stable, and the value depends on the converter. The feedback network has to be symmetric to the millimetre, because an imbalance converts common mode noise into a differential error and raises the second harmonic. That is why the packages put the two feedback pins next to each other and why the layout is part of the electrical specification.

The tables below list the parts we quote most often for precision measurement, medical front ends and high speed acquisition. Bandwidth, slew rate, noise, supply and package come from the maker data sheet for each order code.

Key Specifications

ParameterTHS4551THS4521ADA4932-1AD8138LMH5401
Channels11111
Bandwidth at unity gain150 MHz145 MHz560 MHz small signal320 MHz8 GHz gain bandwidth product, 6.2 GHz small signal
Slew rate220 V per us490 V per us2800 V per us1150 V per us17500 V per us
Input voltage noise3.3 nV per root HzLow noise precision part3.6 nV per root Hz5 nV per root Hz1.25 nV per root Hz
Offset voltage175 uV maximum at 25 CPrecision grade0.5 mV typical1 mV typical0.5 mV typical
Supply voltage2.7 V to 5.4 V single supply2.5 V to 5.5 V3 V single to plus or minus 5 V3 V single to plus or minus 5 V3.3 V to 5 V, single or split
Quiescent current1.37 mA at 5 VLow power part, see data sheet9.6 mA per amplifierAbout 90 mW at 5 V55 mA
Output common mode controlDedicated pin, wide rangeDedicated pinDedicated pinDedicated pinDedicated pin
PackageWSON-8SOIC-8, VSSOP-8LFCSP-16SOIC-8, MSOP-8UQFN-14

Included Models and Order Codes

The order codes below are the ones we quote most often, with the packaging suffix where it matters. The two channel versions of the ADA4932 share the same die and differ in channel count and package. Where a figure is not published for that exact code the cell is left empty rather than copied from a sister part.

Part NumberChannelsBandwidthSlew rateSupplyPackage
THS4551IDGKR1150 MHz220 V per us2.7 V to 5.4 VVSSOP-8
THS4551IRGTR1150 MHz220 V per us2.7 V to 5.4 VWQFN-16
THS4521ID1145 MHz490 V per us2.5 V to 5.5 VSOIC-8
THS4521IDGKR1145 MHz490 V per us2.5 V to 5.5 VVSSOP-8
ADA4932-1YCPZ-R71560 MHz2800 V per us3 V to plus or minus 5 VLFCSP-16
ADA4932-2YCPZ-R72560 MHz2800 V per us3 V to plus or minus 5 VLFCSP-24
AD8138ARZ1320 MHz1150 V per us3 V to plus or minus 5 VSOIC-8
AD8138ARMZ1320 MHz1150 V per us3 V to plus or minus 5 VMSOP-8
LMH540118 GHz gain bandwidth product17500 V per us3.3 V to 5 VUQFN-14
LTC6409110 GHz gain bandwidth product3300 V per us2.7 V to 5.25 VQFN-16

Key Features

Common mode set by a dedicated pin – the output average is driven from the converter reference, so the input range of the ADC is used end to end instead of being trimmed in firmware.

Offset and drift quoted for high resolution – 175 microvolts maximum offset and 1.8 microvolts per degree drift on the THS4551 are the figures that decide whether a 24 bit converter keeps its last two codes.

Noise stated at the input – 3.3 to 5 nanovolts per root hertz on the precision parts and 1.25 on the RF part, so the noise budget against the source impedance can be closed before the part is chosen.

Single ended to differential in one stage – the parts take a single ended input and drive a balanced output, which removes a transformer or a second amplifier from the signal chain.

Supply from 2.7 V – the precision parts run from 2.7 V to 5.4 V, so a 3.3 V rail is enough and the converter and the driver can share it.

Bandwidth from 145 MHz to 8 GHz in one family – the same functional block covers a weigh scale and an instrument front end, so the layout and the feedback network approach carry across projects.

Two channel version for I and Q – the ADA4932-2 puts two matched channels in one package, which keeps the two paths of a quadrature front end thermally together.

Applications

These parts are quoted for products that drive a converter or a balanced line, typically where:

Precision measurement and weigh scales – a 24 bit converter behind a load cell needs low offset and low drift, and the driver sets the common mode to the reference so the bridge is read end to end.

Medical and biopotential front ends – an ECG or EEG channel needs a balanced input with high common mode rejection, and the driver presents a defined impedance to the electrodes.

High speed acquisition and RF front ends – an instrument that samples at hundreds of megasamples per second needs a driver with gigahertz bandwidth and low distortion at the sampling clock.

The driver sits between the sensor front end and the converter on the same board, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that board.

Sourcing and Cross-Reference

Selection starts with the converter. Its resolution, sampling rate and input common mode range set the noise, the bandwidth and the supply of the driver, and a part chosen for bandwidth alone will lose codes on a 24 bit converter because its offset and drift are too large. The second check is the source: a high impedance sensor is dominated by the amplifier current noise and the feedback resistors, while a 50 ohm source is dominated by the amplifier voltage noise, and the two cases point at different parts.

The layout is part of the electrical specification. The feedback network has to be symmetric, the two feedback pins sit next to each other for that reason, and the output series resistors and the differential capacitor that keep the loop stable with a switched capacitor load come from the converter data sheet rather than from the amplifier data sheet alone. A part that is stable on the bench with a scope probe can oscillate on a converter input, so the load is part of the test.

Where a part is obsolete or short, the swap is checked on bandwidth, noise, supply, common mode range and pinout at once, because a faster part with more noise will not improve a precision channel. The route for obsolete and last time buy parts is on our source obsolete components page, and the electrical comparison is on amplifier cross reference. Related families are listed under amplifiers and comparators and analog and mixed signal ICs.

For volume builds, SUPERB Assembly support covers the symmetric feedback network, the output series resistors and the ground plane under the converter and its driver.

Q: Can you quote THS4551IDGKR and ADA4932-1YCPZ-R7, and confirm which one keeps the last two codes on an 18 bit converter?

A: Yes. Send the converter, the source impedance and the supply rail, and the SUPERB Tech team will confirm the driver, the feedback values and the noise contribution from the maker data sheet before quoting.

Why Buyers Source ADC Drivers Through SUPERB

  1. Noise budget closed against the source: the amplifier voltage and current noise are compared with the source impedance, which is the check that decides between a precision and a high speed part.
  2. Offset and drift quoted for the converter: the maximum offset and its drift are given in microvolts, because a millivolt offset is several thousand codes on a 24 bit converter.
  3. Common mode range checked: the output common mode range is confirmed against the converter reference, so the driver is not quoted for a setting it cannot reach on a 3.3 V rail.
  4. Feedback network values given with the part: the resistor and capacitor values that keep the loop stable with a switched capacitor load are quoted, because that is where a working bench circuit fails on a converter.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: instrumentation amplifiers for bridge signals, precision operational amplifiers, 16 bit SAR ADCs, 24 bit delta sigma ADCs.