Phototransistors for Optical Sensing and Isolation
Product Specifications
Product Overview
A phototransistor is a photodiode with a built in current gain. Light generates base current in the exposed junction, the transistor multiplies it by its hFE, and the collector current that results is large enough to drive a comparator or a logic input through a resistor. That gain is why a phototransistor is chosen over a photodiode for presence detection and for light level switching, and why it is the wrong choice for a linear measurement or a fast optical link.
The sensitivity figure is quoted as light current at a stated illuminance. A visible light part is quoted at 100 lx of illuminant A, which is a defined spectrum close to a filament lamp, and the same part reads differently under a white LED or under daylight, so the number is a comparison between parts and not a calibration of the system. An infrared part is quoted at 1 mW per square centimetre at 950 nm instead, because its use is a beam, not a room.
Half angle is the second figure that decides the part. A 20 degree part sees a narrow cone and is used behind a tube or a slot, a 60 degree part sees a wide area and is used behind a diffuser for ambient light sensing. The peak wavelength then has to match the source: 570 nm for a part that follows the human eye, 850 nm to 950 nm for a part that works with an infrared emitter.
The table below covers the groups we quote most often: 3 mm and 5 mm leaded parts for light switching, a flat top 5 mm part with a wide angle, a 1206 surface mount part with an AEC-Q101 grade for ambient sensing, and TO-18 infrared parts with a glass lens for beam detection. Light current, half angle, peak wavelength, collector voltage and package come from the maker data sheet for each code.
Key Specifications
| Parameter | Leaded 3 mm and 5 mm, visible | Surface mount 1206, visible | TO-18, infrared |
|---|---|---|---|
| Light current at 100 lx | 75 uA to 350 uA at 5 V | 50 uA at 5 V | not specified in lux |
| Light current at 1 mW/cm2, 950 nm | not specified | not specified | 7.5 mA to 15 mA |
| Peak sensitivity wavelength | 570 nm | 570 nm | 850 nm |
| Spectral bandwidth | 430 nm to 800 nm | 430 nm to 800 nm | 450 nm to 1080 nm |
| Angle of half sensitivity | 20 degrees to 50 degrees | 60 degrees | 10 degrees |
| Collector emitter voltage | not published as one figure for the leaded visible family | 6 V | 70 V |
| Collector current, continuous | 20 mA on the 1206 part, higher on the TO-18 parts | 20 mA | 50 mA |
| Dark current | 50 nA at 5 V on the 1206 part | 50 nA at 5 V | 100 nA at 20 V |
| Package | 3 mm and 5 mm leaded | 1206 surface mount | TO-18 with glass lens |
Included Models and Order Codes
The table lists the codes we quote most often. Light current, half angle, peak wavelength, voltage rating and package come from the maker data sheet for that code. The light current column states its test condition, because a figure measured at 100 lx and a figure measured at 1 mW per square centimetre are not comparable and the two are never mixed in one quotation.
| Part Number | Light current | Peak wavelength | Half angle | VCEO | IC max | Package |
|---|---|---|---|---|---|---|
| TEMT6000X01 | 50 uA at 100 lx, 5 V | 570 nm | 60 degrees | 6 V | 20 mA | 1206 surface mount |
| TEPT4400 | 200 uA at 100 lx, 5 V | 570 nm | 30 degrees | not listed separately | not listed separately | 3 mm leaded |
| TEPT5600 | 350 uA at 100 lx, 5 V | 570 nm | 20 degrees | not listed separately | not listed separately | 5 mm leaded |
| TEPT5700 | 75 uA at 100 lx, 5 V | 570 nm | 50 degrees | not listed separately | not listed separately | 5 mm flat top |
| BPW77NA | 7.5 mA to 15 mA at 1 mW/cm2 | 850 nm | 10 degrees | 70 V | 50 mA | TO-18 |
| BPW77NB | 10 mA or more at 1 mW/cm2 | 850 nm | 10 degrees | 70 V | 50 mA | TO-18 |
Key Features
Light current quoted with its test condition – 50 uA at 100 lx and 7.5 mA at 1 mW per square centimetre are figures from two different tests, and the condition is stated so a visible part is not compared with an infrared part.
Half angle matched to the optics – a 20 degree part sits behind a tube or a slot, a 60 degree part sits behind a diffuser, and the angle is chosen before the load resistor because it sets the light that reaches the die.
Gain replaces an amplifier – the internal current gain turns a few microamps of photocurrent into milliamps of collector current, which drives a comparator input directly and removes a transimpedance stage from the board.
Collector voltage stated per family – 6 V on the 1206 part and 70 V on the TO-18 part decide whether the device can sit on a 5 V rail directly or needs its own collector supply.
Dark current at a stated voltage – 50 nA at 5 V and 100 nA at 20 V set the off state leakage, which is the figure that limits the detection threshold in a dark enclosure.
Infrared parts with a glass lens – the TO-18 parts reach 7.5 mA to 15 mA at 1 mW per square centimetre with a 10 degree angle, which suits a beam break at a metre rather than an ambient light reading.
Applications
These parts are quoted for boards that detect light or a beam, typically where:
Ambient light switching and dimming – a 1206 part behind a diffuser reads the room and the controller sets the backlight, with the 60 degree angle chosen so the reading does not depend on where the user stands.
Beam break and position detection – a TO-18 part with a 10 degree angle pairs with an 850 nm emitter across a slot, and the 7.5 mA collector current at 1 mW per square centimetre switches a comparator without further gain.
Isolation and encoder readout – a leaded visible part reads a reflective or slotted disc in a motor encoder, where the 20 degree part gives the sharpest edge and the 50 degree part tolerates mechanical misalignment.
The phototransistor sits on the sensor board, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.
Sourcing and Cross-Reference
Selection starts from the source. A visible light part is chosen when the light is a room or a display and the figure of merit is the response to the human eye; an infrared part is chosen when the light comes from an emitter on the same board and the figure of merit is the current at a stated irradiance. The two are not interchangeable even when the packages look similar.
The second check is the load. The collector current at the working illuminance, the dark current and the collector voltage together set the resistor and the threshold, and the rise time falls as the resistor rises. A part with 350 uA at 100 lx can use a 10 k resistor and still drive a comparator; a part with 50 uA needs a higher value or a second stage.
Where a code has been discontinued, the substitution is checked on light current at the same test condition, half angle, peak wavelength and package outline. A part with the same peak wavelength and a different half angle changes the optics, so the window or the tube is reviewed with the part. The route for these checks is on our obsolete part cross reference hub, and the drop in comparison is on pin to pin cross reference.
For volume builds, SUPERB Assembly support covers the optical window clearance, the black potting that stops light piping and the lead forming on the 3 mm and 5 mm parts.
Q: Can you supply a 1206 phototransistor and a matching 850 nm emitter as a pair for a slot sensor?
A: Yes. Send the light source, the distance, the switching threshold and the package, and the SUPERB Tech team will confirm the light current at the stated test condition, the half angle and the pinout from the maker data sheet before quoting.
Why Buyers Source Phototransistors Through SUPERB
- Sensitivity quoted with the test: the light current is given at 100 lx or at 1 mW per square centimetre, so visible and infrared parts are compared on the same basis.
- Optics chosen with the part: half angle and peak wavelength are quoted together, which is the pair that decides the window and the emitter.
- Dark current stated: the off state leakage is given with its voltage, so the detection threshold in a closed enclosure is set from data rather than from a guess.
- Emitter pairs offered: where a slot or a reflective sensor needs an emitter, the matching wavelength part is quoted with the detector.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Sensors and detectors, PIN and avalanche photodiodes, LED indicators and optocouplers, Ambient light and proximity sensors, Temperature and humidity sensors, Pin to pin cross reference.