Contact Us
  • Home
  • COMPONENTS
  • MEMS and Programmable Oscillators for Clock Trees

MEMS and Programmable Oscillators for Clock Trees

A MEMS oscillator replaces the quartz blank with a silicon resonator and a temperature compensated circuit, so the frequency is set in test and not by the cut of a crystal. That makes every frequency a stocked part number, removes the custom frequency lead time, and holds stability under shock and vibration that breaks a quartz blank. The table below lists frequency range, stability, output, supply and package for the codes we quote most often.
quote now

Product Specifications

Product Overview

A MEMS oscillator is a silicon resonator with an analog compensation loop and an output driver in one package. The resonator is a tiny beam that is driven electrostatically at its mechanical resonance, and a temperature sensor with a correction table holds the output frequency over temperature. Because the frequency is trimmed in test, the same die becomes a 24 MHz part or a 25 MHz part, which is why a programmable family can cover 1 MHz to 110 MHz with a short order code change instead of a custom quartz blank.

The reason buyers move from quartz to MEMS is usually lead time and inventory rather than performance. A quartz oscillator at a non standard frequency needs a custom blank, which historically meant 8 to 16 weeks and a minimum quantity, and it meant a part that could only be used on one board. A programmable MEMS part at the same frequency is either in stock or programmed in days, and one family covers several boards, so a production line that runs six products no longer carries six oscillator part numbers that cannot be substituted.

The second reason is mechanical. A quartz blank is a piece of crystal held by two or four mounting points, and shock above a few thousand g can crack it or shift the frequency permanently. Silicon resonators are specified to 30,000 g and show no activity dip, the region where a quartz part can jump in frequency near a particular load capacitance. Equipment that is dropped, vibrated on a vehicle or potted in a housing benefits from this more than from any electrical parameter on the data sheet.

Performance is a trade, and the trade is phase jitter. A standard MEMS part has 1 to 2 ps of RMS jitter integrated from 12 kHz to 20 MHz, which is fine as a reference for an MCU, a USB PHY, an FPGA configuration clock or an Ethernet PHY, and it is not fine as the sampling clock of a high speed ADC or a serializer above 10 Gbps. Those still take a quartz or a SAW part, or a MEMS part in the differential family with a much lower jitter figure, and the quotation says which one applies.

Stability is quoted over the full temperature range and not at 25 degrees centigrade. An ordinary MEMS XO is 20 to 50 ppm over -40 to 85 degrees centigrade; a temperature compensated MEMS part such as the SiT5156 is 0.5 to 2.5 ppm; a Super-TCXO such as the SiT5356 is 100 ppb and holds it under airflow and fast temperature change, which is what a GNSS receiver or a small cell needs. The stability class decides the price far more than the frequency does, so the required figure is confirmed before a code is quoted.

Key Specifications

ParameterSiT8008BIDSC1001CI2SiT5356 Super-TCXO
TypeProgrammable MEMS XO, single endedMEMS XO, single endedTemperature compensated MEMS, high stability
Frequency range1 MHz to 110 MHz1 MHz to 150 MHz1 MHz to 60 MHz
Stability over temperature20, 25 or 50 ppm25 or 50 ppm100 ppb
OutputLVCMOSLVCMOSLVCMOS
Supply1.8 V, 2.5 V, 2.8 V, 3.0 V or 3.3 V1.8 V to 3.3 V2.5 V or 3.3 V
Phase jitterAbout 1 ps RMS, 12 kHz to 20 MHzAbout 2 ps RMS, 12 kHz to 20 MHzAbout 0.3 ps RMS, 12 kHz to 20 MHz
Current4.5 mA at 3.3 V, 25 MHz6 mA at 3.3 V, 25 MHz45 mA at 3.3 V, 10 MHz
Start upUnder 5 msUnder 5 msUnder 10 ms
Package3225, 2520 or 20163225 or 25205032 or 7050

Included Models and Order Codes

The table lists the codes quoted most often for MCU references, USB and Ethernet clocks, FPGA configuration, camera modules and GNSS timing. Frequency, stability, output and package come from the maker data sheet for that code. A programmable part is ordered by frequency inside the family range, so the trailing digits in the code are the frequency and not a fixed option.

Part NumberTypeFrequency rangeStabilityOutputSupplyPackage
SiT8008BI-11-33E-25.000000Programmable MEMS XO1 to 110 MHz, fixed at 25 MHz25 ppmLVCMOS3.3 V3225, 3.2 x 2.5 mm
SiT8008BI-21-18E-16.000000Programmable MEMS XO1 to 110 MHz, fixed at 16 MHz25 ppmLVCMOS1.8 V3225, 3.2 x 2.5 mm
SiT8008AI-11-33E-24.000000Programmable MEMS XO1 to 110 MHz, fixed at 24 MHz20 ppmLVCMOS3.3 V3225, 3.2 x 2.5 mm
SiT8008BI-71-33E-50.000000Programmable MEMS XO1 to 110 MHz, fixed at 50 MHz50 ppmLVCMOS3.3 V2016, 2.0 x 1.6 mm
SiT1602BI-11-33E-12.000000Programmable MEMS XO, low power1 to 110 MHz, fixed at 12 MHz25 ppmLVCMOS3.3 V2520, 2.5 x 2.0 mm
SiT1602AI-21-25E-8.000000Programmable MEMS XO, low power1 to 110 MHz, fixed at 8 MHz20 ppmLVCMOS2.5 V2520, 2.5 x 2.0 mm
SiT9120AI-11-33E-100.000000Differential MEMS XO1 to 220 MHz, fixed at 100 MHz20 ppmLVPECL3.3 V3225, 3.2 x 2.5 mm
SiT9121AI-21-33E-156.250000Differential MEMS XO1 to 220 MHz, fixed at 156.25 MHz25 ppmLVDS3.3 V3225, 3.2 x 2.5 mm
SiT9365AI-11-33E-312.500000Differential MEMS XO, high frequency220 to 725 MHz20 ppmLVDS or LVPECL3.3 V5032, 5.0 x 3.2 mm
SiT5156AI-FK-33E-40.000000Temperature compensated MEMS XO1 to 60 MHz, fixed at 40 MHz0.5 ppmLVCMOS3.3 V5032, 5.0 x 3.2 mm
SiT5356AI-FQ-33E-10.000000Super-TCXO, high stability1 to 60 MHz, fixed at 10 MHz100 ppbLVCMOS3.3 V7050, 7.0 x 5.0 mm
SiT1533AI-H4-DCC-32.76800032.768 kHz MEMS XO32.768 kHz fixed20 ppmLVCMOS1.5 to 3.63 V2012, 2.0 x 1.2 mm
SiT1552AI-JE-DCC-32.76800032.768 kHz MEMS TCXO32.768 kHz fixed5 ppmLVCMOS1.5 to 3.63 V2012, 2.0 x 1.2 mm
DSC1001CI2-025.0000MEMS XO1 to 150 MHz, fixed at 25 MHz25 ppmLVCMOS3.3 V3225, 3.2 x 2.5 mm
DSC1001DI2-050.0000MEMS XO1 to 150 MHz, fixed at 50 MHz25 ppmLVCMOS1.8 to 3.3 V2520, 2.5 x 2.0 mm
DSC1101CI2-100.0000Differential MEMS XO2.3 to 170 MHz, fixed at 100 MHz25 ppmLVPECL2.5 V or 3.3 V3225, 3.2 x 2.5 mm
DSC1121CI2-125.0000Differential MEMS XO2.3 to 170 MHz, fixed at 125 MHz25 ppmLVDS2.5 V or 3.3 V3225, 3.2 x 2.5 mm
DSC1123CI2-100.0000Clock output for PCIe references2.3 to 170 MHz, fixed at 100 MHz25 ppmHCSL3.3 V3225, 3.2 x 2.5 mm
DSC6001CI2A-024.0000MEMS XO, small package1 to 100 MHz, fixed at 24 MHz25 ppmLVCMOS1.8 to 3.3 V1612, 1.6 x 1.2 mm
DSC1033CI2-048.0000MEMS XO, low power1 to 150 MHz, fixed at 48 MHz25 ppmLVCMOS1.8 to 3.3 V2520, 2.5 x 2.0 mm

Key Features

Any frequency without a custom blank – a quartz part at 24.576 MHz and one at 25 MHz are two different blanks with two lead times, while a programmable MEMS family covers both from the same die and the same stock line.

Frequency set in test, not by the crystal cut – the output is trimmed against a reference during programming, so the tolerance the data sheet quotes is the tolerance the part ships with, and no load capacitance calculation is needed on the board.

30,000 g shock rating – a silicon resonator has no mounting points to crack, so a part that is potted, dropped or mounted on a vibrating chassis does not shift frequency or fail open the way a quartz blank can.

No activity dip near a load capacitance – a quartz part can jump tens of ppm at a particular load, and a MEMS part has no such region, which removes an intermittent clock fault that is hard to reproduce in test.

Start up in a few milliseconds – a MEMS part is stable within 5 ms of power on, so a system that wakes from sleep can clock its bus immediately instead of waiting 10 ms for a quartz oscillator.

Stability class is the real cost driver – the same 10 MHz frequency is a few cents at 50 ppm and a large multiple of that at 100 ppb, so the figure the application actually needs is agreed before a code is quoted.

Jitter decides where MEMS stops – 1 to 2 ps RMS is fine for an MCU, USB, Ethernet or FPGA configuration clock and not fine for a 10 Gbps serializer sampling clock, where a quartz or a low jitter differential part stays.

Spread spectrum for EMI – a programmable part can be ordered with spread spectrum modulation, which lowers the peak of a clock harmonic by several dB without a shield can or a ferrite bead on the clock line.

Applications

These parts are quoted for boards that need a clock and a short lead time, typically where:

MCU and FPGA reference clocks – an MCU boot clock and an FPGA configuration clock are both single ended and jitter tolerant, so a programmable 25 MHz or 50 MHz part covers several boards from one family.

Ethernet and USB PHYs – a PHY needs 25 MHz or 24 MHz within 50 ppm, and a MEMS part holds that figure over temperature where a cheap quartz part drifts at the ends of the range.

Portable and wearable devices – a 2016 or 1612 package with a 1.8 V supply fits beside a small battery, and the 5 ms start up lets the radio wake and transmit without a long settling window.

GNSS and timing modules – a receiver needs 0.5 ppm or better to keep a fix, and a Super-TCXO holds 100 ppb through airflow and fast temperature change that would move a plain TCXO.

Industrial and vehicle mounted electronics – vibration and shock are the normal case on a machine or a vehicle, so a part rated to 30,000 g removes a failure mode that shows up as an intermittent clock.

Cameras and display modules – a camera module clock and a display timing clock are fixed frequencies in a small package, and programming them from one family shortens the bill of materials.

The oscillator sits beside the MCU and the PHY on the same board, so it is quoted with the SUPERB PCB and the assembly of that clock section.

Sourcing and Cross-Reference

Sourcing starts with the stability class, then the output type, then the package. A 50 ppm part costs a fraction of a 0.5 ppm part at the same frequency, so quoting a TCXO where an ordinary XO would do is a common way to overpay, and quoting an ordinary XO for a GNSS receiver is a common way to lose the fix. On the SUPERB PCBA builds we quote, the stability figure is taken from the worst case temperature the product sees and not from the room temperature measurement on a bench.

The second item is the programmable side of the order. A MEMS family is programmed to a frequency, so the exact frequency, the stability grade, the supply and the package all have to be written into the order code, and a missing character can mean a different voltage or a different package. We confirm the full code against the programming guide, and where a frequency is not in the family range the nearest quartz part is offered instead of a promise.

The third item is substitution. Because a programmable part is a programmed part, a second source is not a drop in replacement even at the same frequency: the output drive, the start up time and the current differ, and the load on the clock line has to be checked. We quote the alternate code with the differences stated, keep the programming specification on file, and confirm the frequency against the board netlist before the order is released.

For volume builds, SUPERB Assembly support covers the oscillator footprint, the supply decoupling, the clock line routing and the programming code on the reel label.

Q: Can you quote SiT8008BI at 25 MHz in 3225 with 25 ppm, and send the alternate code in case that family has a lead time?

A: Yes. Send the frequency, the stability the application needs and the supply rail, and the SUPERB Tech team will confirm the order code, the package and the alternate from the maker data sheet before quoting.

Why Buyers Source MEMS Oscillators Through SUPERB

  1. Full order code confirmed: the stability grade, supply and package are separate characters in the code, so the complete string is checked against the programming guide instead of being quoted from the family name.
  2. Stability matched to the application: the temperature range the product sees sets the class, so a 50 ppm part is quoted where it works and a TCXO only where the fix or the link needs it.
  3. Lead time stated per frequency: a programmed frequency and a stocked frequency have different availability, and the quotation says which one applies rather than quoting a family lead time.
  4. Alternate quoted with the differences: a second source at the same frequency is not a drop in part, so the alternate is offered with its drive, start up and current stated.
  5. Frequency checked against the netlist: the clock frequency on the board file is confirmed before the order, because a wrong trailing digit is a board that does not boot and a reel that cannot be used.
  6. Small package options kept in stock: 2016 and 1612 parts are quoted alongside the 3225 for boards where the clock area is the last space to give.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Crystals and oscillators, Crystal units and TCXO oscillators, VCXO and OCXO modules, PCIe clock generators and redrivers, STM32F103 mainstream MCUs, Sourcing obsolete components.