Contact Us
  • Home
  • COMPONENTS
  • Ceramic Chip Antennas for GNSS and Short Range Radios

Ceramic Chip Antennas for GNSS and Short Range Radios

A chip antenna is a small ceramic resonator that only behaves as specified on the ground plane and matching network the maker used for the measurement. The 2.4 GHz parts on this page give 0.5 dBi to 2 dBi of peak gain and 9.5 dB of return loss across 2400 to 2500 MHz. Every part needs a matching network, and the values differ between the two layouts the maker publishes. Each row lists band, gain, return loss and maximum input power.
quote now

Product Specifications

Product Overview

A ceramic chip antenna is not a drop in part. It is a resonator that the maker tunes against a specific ground plane, a specific clearance area and a specific matching network, and the gain figure in the data sheet is only reached when all three match. A part that measures 0.5 dBi on the evaluation board can lose several dB on a product board with a ground plane that is half the size, and the loss appears as shorter range rather than as a failed test.

The two 2.4 GHz families in this list show the range. The 1206 size part runs from 2400 to 2500 MHz with 0.5 dBi peak gain, average gain of -0.5 dBi and a return loss of 9.5 dB minimum, which suits a small radio where the antenna sits at the edge of a 20 to 30 mm board. The larger part reaches 2 dBi peak gain with the same 9.5 dB return loss and a 2 W input rating, which is the choice when the link budget matters more than the footprint.

The matching network is part of the antenna, not an optional extra. The Johanson data sheets give the component values for two different layouts, a vertical mount and a horizontal mount, and the values differ, which is why the same antenna can measure well on one board and poorly on another. The recommendation is to copy the maker layout for the first article, measure the return loss at the connector, and only then shrink the ground plane.

Ground plane size is the second trap. A chip antenna needs a ground plane that is a significant fraction of a wavelength, and a 2.4 GHz layout therefore wants at least 20 to 30 mm of copper beside the part, with no battery, no shield can and no metal connector inside the keep out area. A metal enclosure moves the resonance and usually costs more than the antenna gain, which is why plastic or a slot in the metal is part of the antenna decision.

For GNSS the problem is narrower bandwidth and a much weaker signal, so a 1575 MHz chip antenna is used with an active front end or a patch rather than on its own. On this page the GNSS part is listed with its band, and the gain and efficiency figures are taken from the maker data sheet rather than assumed from the 2.4 GHz parts, because the two do not scale.

Key Specifications

ParameterValueApplies to
Frequency range2400 to 2500 MHz2450AT18A, 2450AT43A
Impedance50 ohm unbalancedAll parts
Peak gain0.5 dBi typical, 2 dBi2450AT18A100, 2450AT43A100
Average gain-0.5 dBi typical2450AT18A100
Return loss9.5 dB minimum2450AT18A100, 2450AT43A100
Insertion loss0.5 dB2450AT18A100
Maximum input power2 W2450AT43A100
Case size1206, 18-42450AT18A100, AEC version
QualificationAEC-Q2002450AT18A0100002E
Matching networkSeries inductor, shunt capacitor, values per layoutAll parts
MountingSMT, solderAll parts

Included Models and Order Codes

The list gives both the legacy part number and the current order code where the maker has moved to a longer code, because drawings in the field still carry the short form. Gain and return loss are the maker figures on the published evaluation board, and the matching values are quoted from the layout that produced them.

Part NumberBandPeak gainReturn lossMaximum inputCase
2450AT18A1002400 to 2500 MHz0.5 dBi typical9.5 dB minimumPer maker data sheet1206
2450AT18A0100001E2400 to 2500 MHz0.5 dBi typical9.5 dB minimumPer maker data sheet1206, current order code for 2450AT18A100
2450AT18A0100002E2400 to 2500 MHz0.5 dBi typical9.5 dB minimumPer maker data sheet18-4, AEC-Q200 qualified
2450AT43A1002400 to 2500 MHz2 dBi9.5 dB minimum2 WSMT chip
2450AT43A0100001E2400 to 2500 MHz2 dBi9.5 dB minimum2 WSMT chip, current order code for 2450AT43A100
1575AT43A00401575 MHz GNSSPer maker data sheetPer maker data sheetPer maker data sheetSMT chip

Key Features

Two gain classes at 2.4 GHz – A 0.5 dBi 1206 part for a small board and a 2 dBi part for a link limited product, both at 9.5 dB return loss.

Return loss quoted, not assumed – 9.5 dB minimum is stated for each part, which is the figure the matching network has to reach on the product board.

AEC-Q200 option – The 18-4 case version carries the automotive qualification for a radio that sits in a vehicle module.

Published matching values – The maker gives the inductor and capacitor values for two mounting layouts, so the first article can start from a known point.

50 ohm interface – An unbalanced 50 ohm port means the antenna can be measured with the same fixture as the rest of the RF chain.

Input power to 2 W – The larger 2.4 GHz part takes 2 W, which covers a telemetry radio that transmits in bursts.

Applications

Chip antennas are used where the radio has to be on the board itself, with no connector and no external whip.

Telemetry and sensor nodes – A 1206 part at 0.5 dBi on a 25 mm board feeds a sub GHz or 2.4 GHz module in a sealed enclosure with no room for a connector.

Vehicle and asset trackers – The AEC-Q200 version suits a module that is potted and then mounted where vibration and temperature cycling are constant.

Handheld readers – The 2 dBi part covers a handheld where the link budget is the limit and the board can give the antenna a full keep out area.

The antenna is quoted beside the SUPERB PCB and the SUPERB PCBA work on the radio board, because the keep out area and the ground plane are what the gain figure depends on.

Sourcing and Cross-Reference

Antenna parts are cheap and the matching network is where the schedule goes. When a specific chip antenna is not available, a part in the same band with a similar case size can be used, but the matching values have to be recalculated and the return loss measured on the product board. We quote the antenna and the matching passives together so the network is not assembled from two purchases.

The current order code is longer than the legacy one and the two are not always listed together in a customer BOM. We cross the short code to the full code and state the AEC qualified variant separately, because a qualified part and an unqualified part of the same antenna are not interchangeable in a vehicle build.

Where the GNSS band is concerned, we quote the antenna with the low noise amplifier and the filter that follow it, since the antenna gain alone does not decide whether a receiver keeps a fix. That chain is the same one we supply for GNSS modules, so the parts arrive matched.

SUPERB Assembly keeps the antenna area clear of metal, tall parts and cable ties, and measures return loss at the connector on the first article.

Q: Can you supply a chip antenna that covers both the 2.4 GHz band and GNSS on one part?

A: Band, case size and qualification decide it; the SUPERB Tech desk crosses the legacy short code to the current order code and names the AEC qualified version separately.

Why Buy Chip Antennas Through SUPERB

  1. Matching parts quoted together: The antenna and the inductor and capacitor values are quoted as one set, which is what the return loss depends on.
  2. Qualified variant identified: The AEC-Q200 order code is quoted separately, so a vehicle build does not receive an unqualified part.
  3. Legacy code crossed: Old short part numbers are crossed to the current order code, so an existing drawing can be kept without a guess.
  4. Chain level view: The antenna, the filter and the amplifier are quoted together, so the keep out area and the ground plane are checked as one.
  5. Measured, not assumed: Return loss is stated per part, and the quote says which layout it applies to, so a first article has a target to measure against.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: RF Switches and PIN Diode Switches, SAW Filters and Duplexers, RF Gain Blocks and Low Noise Amplifiers, RF Coaxial Connectors and Adapters.