Wireless Charging Receiver and Transmitter ICs
Product Specifications
Product Overview
A wireless charging pair is two chips, not one: a transmitter controller that switches a half bridge or a full bridge into a coil, and a receiver that rectifies the induced voltage and regulates it to a rail the product can use. The two ends talk over the same coil by amplitude shift keying from receiver to transmitter and frequency shift keying the other way, and that in band channel is how the receiver asks for more or less power and how it reports a foreign object. The protocol behind it is the Qi specification from the Wireless Power Consortium, and the version matters because a 5 W baseline pair and a 15 W extended pair are not interchangeable in firmware.
The receiver end usually decides the mechanical and thermal envelope. A 5 W receiver such as the BQ51013B rectifies the coil voltage and regulates 5 V through an internal pass element, so the dissipation is the difference between the rectified voltage and 5 V multiplied by the output current, and that heat sits in the phone or the handset under the coil. A 15 W part such as the STWLC33 or the P9221-R works at a higher coil voltage and a higher output rail with a smaller drop, so the loss per watt is lower, but the coil has to be larger and the alignment tolerance is tighter.
Foreign object detection is the safety function that gets underestimated. A metal object left on the pad absorbs power, heats up, and the transmitter has no way to know it is there except by comparing the power it delivers with the power the receiver reports. The measurement depends on a calibrated Q factor at startup and on the loss budget stored in the transmitter, so a transmitter IC with a proven detection routine and a coil with a known Q are worth more than a cheaper pair that meets the power spec and fails the safety test.
On the transmitter side the input rail sets the topology. A 5 V input transmitter such as the BQ500211A or the NXQ1TXH5 drives a single ended coil from a 5 V adapter, which suits a low cost pad, while a 12 V input part such as the BQ500412 or the P9242-R drives a full bridge into a larger coil for 15 W and needs the input current and the thermal path sized for it. Coil inductance, series resonant capacitor and the DC resistance of the coil are the three values that decide whether the pair reaches its rated power at the rated distance.
Alignment and distance are part of the specification, not a tolerance to be discovered in test. The rated power of a Qi pair is quoted at a defined coil to coil distance, typically 3 to 5 mm, and the same pair delivers less at 8 mm because the coupling coefficient falls. Products with a thick housing or a metal back plate need a spacer ferrite and a coil sized for the gap, and the receiver IC datasheet gives the coil inductance range it can tune, which is why the coil is quoted with the chip rather than sourced separately.
Key Specifications
| Parameter | BQ51013B receiver | STWLC33 receiver | P9242-R transmitter |
|---|---|---|---|
| Function | Receiver with integrated rectifier and linear regulator | Receiver with synchronous rectifier and buck-boost stage | Transmitter controller with external bridge |
| Rated output power | 5 W, 5 V at 1 A | Up to 15 W | Up to 15 W into the coil |
| Output or input rail | 5 V regulated output | 3.5 V to 12 V adjustable output | 5 V to 19 V input, 12 V nominal |
| Protocol | Qi baseline power profile | Qi extended power profile, dual mode | Qi extended power profile |
| In band communication | Amplitude shift keying to the transmitter | Amplitude and frequency shift keying | Frequency shift keying, ASK demodulation |
| Coil range | 10 uH to 20 uH series resonant | 12 uH to 20 uH, dual coil supported | 10 uH to 15 uH with 200 nF resonant capacitor |
| Foreign object detection | Power loss method, calibrated at startup | Q factor and power loss method | Q factor measurement plus loss budget |
| Protection | Over voltage, over current, thermal shutdown | Over voltage, over current, thermal, EPT | Over current, over voltage, coil open and short |
| Package | VQFN20, 3.5 x 4.5 mm | QFN48, 7 x 7 mm | QFN40, 6 x 6 mm |
Included Models and Order Codes
The table lists the receiver and transmitter codes quoted most often for phone accessories, handheld instruments, sealed sensors and small appliances. Rated power, rail and protocol come from the maker data sheet for that code. Receiver codes and transmitter codes are listed together because a product usually needs both ends quoted, even when only one of them ships with the unit.
| Part Number | Function | Rated power | Rail | Protocol | Interface | Package |
|---|---|---|---|---|---|---|
| BQ51013B | Receiver with rectifier and LDO | 5 W | 5 V output | Qi baseline | Analog control, no host bus | VQFN20, 3.5 x 4.5 mm |
| BQ51013BRHLR | Receiver with rectifier and LDO | 5 W | 5 V output | Qi baseline | Analog control, no host bus | VQFN20, 3.5 x 4.5 mm |
| BQ51050B | Receiver with 1.5 A linear charger | 5 W | 4.2 V charging output | Qi baseline | Standalone, status pins | VQFN20, 3.5 x 4.5 mm |
| BQ51020 | Receiver with adjustable output | 5 W | 5 V to 7 V output | Qi baseline | I2C | VQFN40, 5 x 5 mm |
| BQ51021 | Receiver with adjustable output | 5 W | 5 V to 7 V output | Qi baseline | I2C | VQFN40, 5 x 5 mm |
| BQ51025 | Receiver, high voltage output | 10 W | 7 V output | Qi baseline | I2C | VQFN40, 5 x 5 mm |
| BQ500211A | Transmitter controller | 5 W | 5 V input | Qi baseline | Standalone, LED and fault pins | VQFN48, 7 x 7 mm |
| BQ500412 | Transmitter controller | 12 W | 12 V input | Qi baseline | Standalone, fault pins | VQFN48, 7 x 7 mm |
| BQ501210 | Transmitter controller | 15 W | 12 V input | Qi extended | I2C and fault pins | VQFN48, 7 x 7 mm |
| NXQ1TXH5 | Transmitter with integrated bridge | 5 W | 5 V input | Qi baseline | Standalone, no host bus | HVQFN32, 5 x 5 mm |
| MWCT1012 | Transmitter controller | 5 W | 5 V or 12 V input | Qi baseline | I2C and UART | QFN32, 5 x 5 mm |
| MWCT1013A | Transmitter controller | 15 W | 12 V input | Qi extended | I2C and UART | QFN48, 7 x 7 mm |
| STWLC33 | Receiver with buck-boost stage | 15 W | 3.5 V to 12 V output | Qi extended, dual mode | I2C | QFN48, 7 x 7 mm |
| STWLC68 | Receiver with linear stage | 5 W | 5 V output | Qi baseline | I2C | QFN32, 5 x 5 mm |
| P9221-R | Receiver with buck stage | 15 W | 5 V to 9 V output | Qi extended | I2C | QFN40, 6 x 6 mm |
| P9235A-R | Receiver with linear stage | 5 W | 5 V output | Qi baseline | I2C | QFN32, 5 x 5 mm |
| P9242-R | Transmitter controller | 15 W | 12 V nominal input | Qi extended | I2C | QFN40, 6 x 6 mm |
| WLC1115 | Transmitter controller | 15 W | 5 V to 24 V input | Qi extended | I2C and UART | QFN40, 6 x 6 mm |
| STWBC2-HP | Transmitter controller | 15 W | 12 V nominal input | Qi extended | I2C and UART | QFN48, 7 x 7 mm |
Key Features
Receiver heat is set by the drop – a linear receiver burns the rectified voltage minus 5 V across its pass element, so a 5 W unit at 1 A with 1.5 V of headroom dissipates 1.5 W inside a phone housing that has no airflow.
Buck based receivers cut the loss – the STWLC33 and P9221-R regulate with a switching stage, so the loss tracks the output power instead of the voltage drop and a 15 W unit can stay inside a sealed enclosure.
In band communication has no extra pins – the receiver modulates the coil load and the transmitter reads the change in coil current, so the pair needs no data line across the gap and no alignment of a second contact.
Foreign object detection must be calibrated – the power loss method compares delivered and received power against a stored budget, and a coil with an unknown Q factor will either miss a metal object or trip on a phone case.
Resonant capacitor tolerance sets the power – the series capacitor works with the coil inductance to set the resonant tank, and a 5 percent part shift moves the operating frequency enough to lose several watts at the rated gap.
Thermal derating is a rail decision – a 15 W receiver asked to hold 15 W in a closed case will fold back, so the quotation states the continuous power at the case temperature rather than the peak the data sheet allows.
Transmitter bridge choice follows the rail – a 5 V input drives a single ended coil with an integrated bridge, while 12 V and 15 W need a full bridge with external FETs and a gate drive that survives a coil short.
Coil and ferrite are quoted with the chip – the coil inductance, DC resistance and the ferrite spacer under it decide the coupling, so the three are quoted together, because a receiver chip alone does not define the power.
Applications
These parts are quoted for products that charge without a connector, typically where:
Sealed handheld instruments – a housing with no opening for a connector keeps the IP rating, and a 5 W receiver behind a plastic wall charges the cell overnight without a gasket or a port door.
Medical and hygiene sensitive devices – a sealed enclosure that can be wiped down needs no exposed contacts, so a receiver with an integrated charger such as the BQ51050B removes the charging connector from the risk list.
Phone accessories and charging pads – a 15 W pad pairs a transmitter controller with a full bridge and a three coil array, and the receiver side is chosen for the rail the handset expects.
Industrial sensors and trackers – a potted sensor with a 5 W receiver and a supercapacitor buffer charges during a short dock period and runs for weeks, which is why the receiver rail and the buffer are quoted together.
Small appliances and kitchen tools – a blender or a kettle with no exposed contacts uses a 15 W pair and a foreign object check, because the pad sits on a wet surface and a metal spoon has to be detected.
Wearables and earbud cases – a 5 W receiver in a case with a 300 mAh cell needs the charger and the receiver to share one die, so the codes with an integrated linear charger are the ones quoted.
The receiver sits on the same board as the charger and the protection circuit, so it is quoted with the SUPERB PCB and the assembly of that power section.
Sourcing and Cross-Reference
Sourcing starts at the receiver, because that is where the thermal problem lives. A linear receiver is simple and cheap, and it is the right choice when the product can dissipate 1 to 2 W in a metal frame or a large plastic wall. A switching receiver costs more and needs an inductor, and it is the right choice when the enclosure is sealed, the cell is large, or the rated power is above 10 W. On the SUPERB PCBA assemblies we quote, the receiver dissipation is calculated at the continuous power before the housing is fixed, because a fold back found in thermal test usually means a new receiver and a new coil.
The second item is the coil and the magnetic sheet. The receiver coil inductance has to sit inside the range the chosen IC can tune, the series resonant capacitor has to be a stable dielectric rather than a high K ceramic, and the ferrite sheet behind the coil has to be thick enough to keep the field out of the battery and the ground plane. A coil that is 2 mm larger can add several watts of coupling at the rated gap, and it can also add a millimetre to the product thickness, so the coil drawing is part of the quotation.
The third item is compliance. A charging product is tested against the Qi specification for interoperability and against the safety standard for the enclosure temperature, and the foreign object detection is part of that test rather than a feature to be trusted from the data sheet. We keep the protocol version of each code on file, confirm whether the pair is certified as a set, and quote the coil and the ferrite with the IC so the certification sample matches the production bill of materials.
For volume builds, SUPERB Assembly support covers the coil placement, the resonant capacitor tolerance, the ferrite sheet and the thermal pad under the receiver.
Q: Can you quote a 15 W receiver and a matching transmitter with the coil and ferrite sheet, and confirm which Qi version the pair is certified against?
A: Yes. Send the cell capacity, the enclosure thickness and the required charge time, and the SUPERB Tech team will confirm the receiver, the coil and the transmitter pair from the maker data sheet before quoting.
Why Buyers Source Wireless Charging ICs Through SUPERB
- Receiver loss calculated first: the linear or switching choice is made on the dissipation at continuous power, not on the data sheet peak, so the part survives the thermal test in the real housing.
- Coil and ferrite quoted with the chip: inductance, DC resistance and sheet thickness are listed with the IC, because the rated power belongs to the pair and not to the receiver alone.
- Protocol version stated per code: a baseline pair and an extended pair are not interchangeable, so the Qi version is written on the quotation instead of being assumed from the family name.
- Foreign object detection taken seriously: the detection method and the calibration requirement are stated with the transmitter, because a metal object on the pad is a safety test failure and not a firmware detail.
- Both ends of the link quoted: the receiver and the transmitter are quoted as a set, so the coil, the resonant capacitor and the bridge are matched before the product is committed.
- Chip down or module argued both ways: a certified module removes the radio and safety test cycle, a chip down route gives the thickness and the cost, and the quotation says which one fits the volume.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Power management ICs, Battery chargers and fuel gauges, Battery protection ICs and BMS front ends, Load switches and hot swap controllers, Step-down DC-DC converters, Sourcing obsolete components.