Contact Us
  • Home
  • COMPONENTS
  • Battery Protection ICs and BMS Analog Front Ends

Battery Protection ICs and BMS Analog Front Ends

Protection and monitoring devices for lithium packs from one cell to eighteen cells in series. Cell measurement of 5 mV at 25 degrees on the BQ76952, with coulomb counting on the same die. Single cell protectors add overcharge, overdischarge and short circuit cut off in a 1.5 mm package. isoSPI and I2C interfaces for packs that stack several monitors.
quote now

Product Specifications

Product Overview

A lithium pack needs three functions that are easy to confuse: protection, which opens the switch before a cell is damaged, monitoring, which reports voltage, current and temperature to the host, and balancing, which moves charge between cells so that the weakest one does not set the pack capacity. A single cell protector does the first on its own. A monitor and protector such as the BQ76952 does all three for a pack of 3 to 16 cells, and a stackable monitor such as the ADBMS1818 does the monitoring across 18 cells and leaves the switch decision to the host.

The integrated parts carry the measurement chain that used to sit outside. The BQ76952 holds cell measurement to plus or minus 5 mV at 25 degrees and to plus or minus 15 mV over the full temperature range, digitises a plus or minus 200 mV sense resistor drop for the coulomb counter with an input offset below 1 microvolt, drives high side N channel FETs from an internal charge pump, and offers two LDOs at 45 mA each for the rest of the board. It talks over 400 kHz I2C, SPI or a single wire HDQ link, and it consumes 286 microamps in normal mode and about 1 microamp in shutdown.

For packs above 16 cells the monitors stack. The ADBMS1818 measures 18 cells and passes data along a 1 MHz isoSPI chain that can run in both directions, so a broken wire in the middle of a stack is reported rather than silently ending the chain, and it balances passively up to 200 mA per cell. At the other end of the range, the BQ29700 is the smallest part on the page: a single cell protector in a 1.5 mm by 1.5 mm package that watches overcharge, overdischarge, charge and discharge overcurrent and load short circuit, with thresholds fixed in the part and 4 microamps of normal mode current.

Key Specifications

ParameterSingle cell protectorMulti cell monitor and protector
Cells in series13 to 16 on BQ76952, 3 to 5 on BQ76920, 6 to 10 on BQ76930, 9 to 15 on BQ76940, 18 on ADBMS1818
Cell measurementComparator thresholds fixed in the partPlus or minus 5 mV at 25 degrees on BQ76952, plus or minus 15 mV over minus 40 to 85 degrees
Current measurementSense across the external FETs, plus or minus 5 mV typicalPlus or minus 200 mV sense resistor range with input offset below 1 uV
Protection setOvercharge, overdischarge, charge and discharge overcurrent, load short circuitCell and pack voltage, current, temperature, with autonomous or host controlled recovery
BalancingNonePassive, host controlled or autonomous on BQ76952; up to 200 mA per cell on ADBMS1818
InterfaceFET drive outputs only400 kHz I2C, SPI and HDQ on BQ76952; 1 MHz isoSPI on ADBMS1818
Supply current4 uA normal, 100 nA shutdown286 uA normal, 24 uA to 41 uA in sleep, about 1 uA shutdown on BQ76952
High side driveExternal N channel FETs driven by CHG and DSG pinsCharge pump for high side N channel FETs on BQ76952
Package6 pin, 1.5 mm by 1.5 mm by 0.75 mm48 pin TQFP 7 mm by 7 mm; 48 pin SSOP and 64 pin LQFP on the stackable monitors

Included Models and Order Codes

The codes below cover single cell packs through 18 cell stacks. State the cell count, the chemistry, the pack current, the interface the host uses and whether the switch is high side or low side, and the part, the grade and the packing are confirmed.

Part NumberCellsCell MeasurementBalancingPackage
BQ29700DSER1Overcharge and overdischarge thresholds fixed in the partNone6 pin, 1.5 mm by 1.5 mm
BQ76920PFBR3 to 5Monitor and protectPassive32 pin TQFP
BQ76930PFBR6 to 10Monitor and protectPassive44 pin TQFP
BQ76940PFBR9 to 15Monitor and protectPassive44 pin TQFP
BQ76952PFBR3 to 16Plus or minus 5 mV at 25 degreesPassive, autonomous or host controlled48 pin TQFP 7 mm by 7 mm
ADBMS1818ASWZ-RL18Monitor with isoSPI chainPassive, up to 200 mA per cell64 pin LQFP
LTC6811IG-1#PBF12Monitor with isoSPI chainPassive48 pin SSOP

Key Features

Protection and measurement on one die – the BQ76952 replaces a comparator network, a separate coulomb counter and a thermistor front end with one part, which shortens the pack harness and removes the drift between the three.

High side switch from a charge pump – an internal charge pump drives N channel FETs on the positive side, so the pack ground stays continuous and the host can still talk to the monitor with the switch open.

Cell accuracy that holds over temperature – plus or minus 5 mV at 25 degrees and plus or minus 15 mV across the full range is what decides whether a 3.6 V cell is reported as full or as overcharged at the end of a fast charge.

Stacking without a repeater – the isoSPI chain runs at 1 MHz and in both directions, so a 96 cell stack is built from six monitors on one twisted pair, and a broken link is reported as a fault.

Balancing current that shortens a service stop – passive balancing up to 200 mA per cell on the ADBMS1818 bleeds the high cell while the pack sits, which is enough to recover a pack that has drifted over a season.

Small pack protector – the BQ29700 needs only a sense resistor and two FETs, so a single cell tool, lamp or wearable gets protection in a 1.5 mm package.

Applications

These parts are quoted for packs that have to be protected and reported, typically where: A pack board is usually quoted with the SUPERB PCB and the SUPERB PCBA work for the same assembly, so the cell input filter and the high current path are reviewed together with the monitor.

Light electric vehicles and power tools – a 10 to 16 cell pack needs one monitor with high side drive, a coulomb counter and a temperature input per group, which is the BQ76952 case in a 48 pin package.

Stationary storage and backup units – a rack built from 18 cell modules stacks several monitors on one isoSPI chain, and the bidirectional link lets the host see which module dropped out.

Single cell instruments and wearables – a handset, lamp or handheld instrument needs overcharge, overdischarge and short circuit cut off in the smallest package, which is what the BQ29700 provides with two external FETs.

Sourcing and Cross-Reference

A battery monitor is tied to the pack, not to the board alone. The sense resistor, the cell input filter, the thermistor network and the OTP settings are part of the qualified build, so a replacement has to match the cell count, the measurement range, the interface and the switch topology before anything else is compared. A part with the same package but a different measurement range will report a different current at the same shunt, and a part with a different charge pump will not drive the same FETs.

Supply is the second issue. Packs in the field are supported for a decade, and the monitors they were built around are not always in stock. We quote the cell count, the interface, the measurement grade and the package on every line, and where a part is being replaced we check the OTP settings and the balancing current against the pack that exists rather than only the pinout.

Where the pack board carries a 48 pin TQFP and a high side FET pair, SUPERB Assembly support covers the reflow and the inspection of the thermal pad and the sense resistor joints.

Q: Can you supply the same battery monitor for a pack that is already in production?

A: Yes. Send the cell count, the chemistry, the interface and the current range, and the SUPERB Tech sales team will confirm the order code and the nearest part that keeps the same measurement range and switch topology.

Why Buyers Source Battery Monitors Through SUPERB

  1. Cell count and interface confirmed: the series range, the interface and the switch side are checked before the order code is quoted, which avoids a part that fits the footprint and not the pack.
  2. Measurement grade on the quote: the cell accuracy and the coulomb counter offset are stated per line, so the state of charge budget is built on real numbers.
  3. Protection parts as one set: the monitor, the FETs, the sense resistor and the thermistors are quoted together, so the protection thresholds are checked against the parts that will be fitted.
  4. Support for long production: packs stay in service for years, so parts are held with date codes while an alternative is qualified against the existing OTP settings.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Power management ICs, Battery chargers and fuel gauges, Load switches and hot swap controllers, Temperature sensors, BOM shortage recovery.