Contact Us
  • Home
  • COMPONENTS
  • Boost and SEPIC Converter Controllers for Wide Input Rails

Boost and SEPIC Converter Controllers for Wide Input Rails

Boost, SEPIC and flyback controllers with input ranges from 2.9 V to 100 V. Synchronous and non-synchronous gate drive options are listed with the peak driver current. Switching frequency, current limit and soft start are set by external parts on every row. Controllers are quoted with the external MOSFET and the sense resistor for a complete stage.
quote now

Product Specifications

Product Overview

A rail that has to go up cannot be built with a buck regulator, and a SEPIC is what an engineer reaches for when the input may sit above or below the output. Both topologies need a controller that drives an external N channel MOSFET, senses the switch current and holds a fixed frequency while the input moves. The difference between the parts on this page is mostly how wide the input can go, how much gate drive current is available and whether the synchronous rectifier is driven by the same chip.

Input range is the first filter. A 12 V instrument rail that dips to 3 V on a battery discharge needs a controller that starts below 3 V, which is where the LM3478 and the LM3481 sit. A telecom or 48 V rail needs a part that survives 60 V and above, which points at the LM5122 at 65 V or the LT3758 at 100 V. A two cell battery product that has to run from 2.75 V and stay small is better served by the LTC3872, which needs no sense resistor and runs at a fixed 550 kHz in a SOT-23 footprint.

Current limit is the second filter, because a boost has no inherent short circuit protection: the switch current continues into the output through the diode even when the output is shorted. Every controller here limits the switch current cycle by cycle, and the synchronous LM5122 adds hiccup mode so a persistent overload does not sit at the limit and cook the inductor. The SEPIC adds a coupling capacitor that blocks DC, which is the reason it survives an output short while a plain boost does not.

Thermal and layout consequences follow from the frequency. A 2.2 MHz part like the LM5155 or the TPS61175 allows a small inductor and ceramic output capacitors, at the cost of higher switching loss in the external MOSFET. A 100 kHz to 500 kHz part allows a larger die and lower loss but needs more board area. The rows below give the frequency range each controller can be set to, not a single number.

Key Specifications

ParameterLow voltage controllerWide input controllerSynchronous boost controller
Typical partsLTC3872, TPS61175, MAX668LM3478, LM3481, LT3757, LT3758LM5122
Input range2.75 V to 18 V2.9 V to 100 V3 V to 65 V
Output voltageup to 38 V on TPS61175, higher with an external switch ratingup to 500 V with external partsup to 100 V
Gate driveinternal switch on TPS61175, external MOSFET on the othersexternal N channel MOSFET3 A driver for both switches
Switching frequency200 kHz to 2.2 MHz, or fixed 550 kHz on LTC387250 kHz to 1 MHz, up to 2.2 MHz on LM5155up to 1 MHz, synchronizable
Current limitcycle by cycle on the switch currentcycle by cycle, adjustablecycle by cycle, programmable, hiccup on overload
PackageSOT-23-8, DFN-8, µMAX-10, HTSSOP-14VSSOP-8, VSSOP-10, WSON-12, MSOP-10E, DFN-10HTSSOP-20, HTSSOP-24
Standby current10 µA to 200 µA depending on part2.6 µA to 10 µA shutdown9 µA shutdown

Included Models and Order Codes

Order codes below are the controllers quoted most often for instrument rails, battery products, telecom cards and LED strings. State the input range including the transient, the output voltage and current, the switching frequency you want and whether the rectifier has to be synchronous, and the controller, the external MOSFET and the sense resistor are confirmed together.

Part NumberTopologyInput RangeSwitching FrequencyGate Drive or SwitchPackage
LM3478Boost, SEPIC, flyback, forward2.97 V to 40 V100 kHz to 1 MHz, synchronizable1 A peak, external MOSFETVSSOP-8, SOIC-8
LM3481Boost, SEPIC, flyback, forward2.97 V to 48 V100 kHz to 1 MHz, synchronizable1 A peak, external MOSFETVSSOP-10
LM5155Boost, SEPIC, flyback3.5 V to 45 V, 1.5 V with bias100 kHz to 2.2 MHz, synchronizable1.5 A peak, external MOSFETWSON-12
LM5122Synchronous boost, multiphase3 V to 65 Vup to 1 MHz, synchronizable3 A driver for both switchesHTSSOP-20, HTSSOP-24
LT3757Boost, SEPIC, flyback, inverting2.9 V to 40 V50 kHz to 1 MHz, synchronizableexternal MOSFET, 7.2 V regulated driveMSOP-10E, DFN-10
LT3758Boost, SEPIC, flyback, inverting5.5 V to 100 V100 kHz to 1 MHz, synchronizableexternal MOSFET, 7.2 V regulated driveMSOP-10E, DFN-10
LTC3872Boost, no sense resistor2.75 V to 9.8 Vfixed 550 kHzexternal MOSFET, DCR sensingSOT-23-8, DFN-8
MAX668Boost, SEPIC, flyback, isolated3 V to 28 V, 1.8 V on MAX669100 kHz to 500 kHz, synchronizableexternal MOSFETµMAX-10
TPS61175Boost, SEPIC, flyback2.9 V to 18 V200 kHz to 2.2 MHzinternal 3 A switch, 3.8 A limitHTSSOP-14

Key Features

Input range quoted with the transient – the operating range and the absolute maximum are given as two numbers, because a 48 V telecom rail with a 60 V transient needs the second one, not the first.

Synchronous or diode rectifier – the LM5122 drives both switches with 3 A, while the others drive one and leave the rectifier to a diode, which is the choice that decides efficiency at 5 V output.

Frequency set by one resistor – every controller on this page sets its switching frequency with an external resistor, and most accept an external clock for synchronisation to avoid beat frequencies between rails.

No sense resistor option – the LTC3872 derives the current from the inductor resistance, which removes a component and its loss from a small battery product.

Current limit that survives a short – a boost cannot limit its output current through the switch alone, so the SEPIC configuration and the hiccup mode of the LM5122 are described on the page rather than left to the data sheet.

Gate drive stated as peak current – 1 A, 1.5 A and 3 A drivers suit different MOSFET gate charges, and the row gives the value instead of a generic strong driver claim.

Start up below the output – the LM5155 starts from 1.5 V with a bias supply and the MAX669 starts at 1.8 V, which matters when the input is two alkaline cells.

One package per function – SOT-23 and DFN parts for space, HTSSOP with a thermal pad for the synchronous stage, so the footprint is picked before the part.

Applications

These controllers are quoted for rails that have to be raised, or that move above and below the output, typically where: The controller sits next to the inductor and the MOSFET on the same card, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that power board.

Instrument and analyser rails – a 5 V to 24 V stage behind a 12 V input needs a quiet, fixed frequency controller, and the LT3757 at 300 kHz keeps the switching harmonic away from a 10 kHz measurement window.

Battery powered devices – a single cell product that has to hold 12 V for a display runs a boost from 3 V to 4.2 V, and the LTC3872 without a sense resistor keeps the board small.

Telecom and industrial 48 V – a 48 V rail with a 60 V transient is handled by the LM5122 at 65 V or the LT3758 at 100 V, and the synchronous rectifier on the LM5122 lifts efficiency at 5 A output.

LED strings and high voltage bias – a string of 20 LEDs at 60 V is driven from a 12 V rail by a boost with an external 100 V MOSFET, and the current limit is set by the sense resistor on the switch.

Sourcing and Cross-Reference

Controller cross references are less forgiving than they look. The feedback threshold, the current limit sense voltage and the compensation pin arrangement differ between families, so a part that shares a package does not necessarily share a board. The LM3478 and the LM3481 sit in the same family and differ in input range and reference accuracy, while the LM5155 replaces both with a higher frequency and a smaller package but a different pinout, which means a board change rather than a part change.

Availability is the second question. Several of these controllers have been in production for more than fifteen years, and the ones that remain active are the ones with a documented replacement path. Where a part is on allocation, the practical options are a higher frequency part with a smaller external inductor, or a synchronous part that reduces the loss enough to allow a smaller package.

The quotation line for a controller usually carries the external MOSFET and the sense resistor as well, because the current limit and the thermal result depend on all three. Sending the input range, the output voltage and current and the switching frequency is enough for a complete stage to be quoted.

For volume builds, SUPERB Assembly support covers the thermal pad reflow, the sense resistor placement and the inductor clearance that a boost stage needs.

Q: Can you quote the controller together with the external MOSFET and the sense resistor for a complete boost stage?

A: Yes. Send the input range, the output voltage and current, the switching frequency and the package you have space for, and the SUPERB Tech sales team will confirm the controller and the external parts that make the stage work.

Why Buyers Source Boost and SEPIC Controllers Through SUPERB

  1. Input range and transient separated: the operating range is quoted next to the absolute maximum, so a 48 V rail with a 60 V transient is not matched to a 48 V only part.
  2. Controller and power parts together: the MOSFET, the inductor and the sense resistor are quoted on the same line, which is what the current limit and the thermal result depend on.
  3. Replacement path known: where a controller has a documented successor with a different pinout, that is stated before a board is changed rather than after.
  4. Topology advice included: a boost that cannot survive an output short is pointed at a SEPIC or at a part with hiccup mode, instead of being quoted into a fault it cannot handle.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Power management ICs, PWM controllers for switching supplies, Charge pump regulators and inverting converters, Isolated DC-DC modules and brick converters, Power management cross reference.