RF Mixers and IQ Modulators for Frequency Conversion
Product Specifications
Product Overview
Every radio that transmits and receives on different frequencies needs a stage that moves a signal from one band to another, and that stage is a mixer. A passive mixer is a switch driven by the local oscillator: it has conversion loss instead of gain, needs almost no dc power, and can hold a high intercept because there is no amplifier to compress. An active mixer puts a transconductance stage in front of the switches, so it delivers conversion gain and a lower noise figure at the cost of supply current and headroom.
The passive parts on this page are built for microwave bands. The LTC5548 covers 2 GHz to 14 GHz on the radio port and 1 GHz to 12 GHz on the local oscillator, with a differential dc to 6 GHz intermediate frequency port, about 8 dB of conversion loss and an input intercept of 24 dBm, from a 3.3 V supply and 0 dBm of local oscillator drive. The LTC5549 keeps the same radio and oscillator ranges and adds an integrated balun for a single ended intermediate frequency port up to 6 GHz. Both are double balanced, so the local oscillator and the even order products are suppressed at the output.
The active parts cover the lower bands. The ADL5801 is a doubly balanced active mixer with an integrated local oscillator buffer, specified from 10 MHz to 6 GHz, which removes the external balun and the drive amplifier from a receiver front end and keeps the intercept high enough for a blocking test. For transmit chains the ADL5375 is a quadrature modulator from 400 MHz to 6 GHz: 9.6 dBm of output compression at 900 MHz, an output intercept of 25.9 dBm, sideband suppression of 52.8 dBc and carrier feedthrough of minus 45.1 dBm at 900 MHz, from a single 5 V supply in a 24 lead LFCSP. The AD831 is the low frequency option, a 500 MHz mixer with a 24 dBm third order intercept that is still used in HF and IF stages.
Key Specifications
| Parameter | Passive mixers | Active mixers and modulators |
|---|---|---|
| Frequency range | 2 GHz to 14 GHz radio, 1 GHz to 12 GHz local oscillator on LTC5548 and LTC5549 | 10 MHz to 6 GHz on ADL5801; 400 MHz to 6 GHz on ADL5375; dc to 500 MHz on AD831 |
| Intermediate frequency | DC to 6 GHz, differential on LTC5548, single ended with integrated balun on LTC5549 | Differential or single ended depending on part |
| Conversion | About 8 dB of conversion loss | Conversion gain on the active mixer, 3.1 dB of voltage gain on the modulator |
| Linearity | 24 dBm input third order intercept | 25.9 dBm output intercept and 9.6 dBm output compression on ADL5375 at 900 MHz; 24 dBm intercept on AD831 |
| Local oscillator drive | 0 dBm, with an internal doubler for the higher bands | Integrated buffer on ADL5801 |
| Spurious performance | Double balanced, local oscillator and even order products suppressed | Sideband suppression of 52.8 dBc and carrier feedthrough of minus 45.1 dBm on ADL5375 at 900 MHz |
| Noise | Conversion loss sets the noise figure | Noise floor of minus 160 dBm per hertz at 900 MHz on ADL5375 |
| Supply | 3.3 V | 5 V on ADL5375, 4.75 V to 5.25 V |
| Package | 24 lead QFN | 24 lead LFCSP on ADL5801 and ADL5375, 20 lead PDIP on AD831 |
Included Models and Order Codes
The codes below cover receive down conversion, transmit up conversion and instrument signal chains. State the radio and intermediate frequencies, the local oscillator power, the intercept the blocking test needs and the supply rails, and the part and the package are confirmed.
| Part Number | Type | Frequency Range | Key RF Performance | Package |
|---|---|---|---|---|
| LTC5548IUH#PBF | Passive double balanced mixer | 2 GHz to 14 GHz radio, dc to 6 GHz IF | 8 dB conversion loss, 24 dBm input intercept | 24 lead QFN |
| LTC5549IUH#PBF | Passive double balanced mixer | 2 GHz to 14 GHz radio, 0.5 GHz to 6 GHz IF | 8 dB conversion loss, 24 dBm input intercept, integrated balun | 24 lead QFN |
| ADL5801ACPZ-R7 | Active mixer | 10 MHz to 6 GHz | Doubly balanced core with integrated local oscillator buffer | 24 lead LFCSP |
| AD831APZ | Active mixer | DC to 500 MHz | 24 dBm third order intercept | 20 lead PDIP |
| ADL5375-05ACPZ-R7 | IQ modulator | 400 MHz to 6 GHz | 9.6 dBm output compression, 25.9 dBm output intercept, 500 mV baseband bias | 24 lead LFCSP |
| ADL5375-15ACPZ-R7 | IQ modulator | 400 MHz to 6 GHz | 9.6 dBm output compression, 23.4 dBm output intercept, 1500 mV baseband bias | 24 lead LFCSP |
Key Features
No dc power in the signal path – a passive mixer needs no bias network on the radio or the intermediate frequency port, which keeps the front end simple and removes a source of drift with temperature.
Intercept that survives a blocking test – 24 dBm of input intercept on the passive parts and 24 dBm on the AD831 keeps the conversion gain from folding a strong nearby carrier onto the wanted channel.
Local oscillator suppression by symmetry – a double balanced core cancels the local oscillator at the output, which reduces the filter that has to follow the mixer in a transmit chain.
Wide intermediate frequency – a dc to 6 GHz intermediate frequency port lets one mixer serve a zero intermediate frequency receiver and a high intermediate frequency architecture without a part change.
Modulator linearity at 900 MHz – 25.9 dBm of output intercept and 52.8 dBc of sideband suppression are what an error vector magnitude budget of a few percent needs from the quadrature stage.
Baseband bias choice – the two ADL5375 versions take 500 mV or 1500 mV of baseband common mode, so the modulator matches the DAC that drives it instead of needing a level shift.
Applications
These parts are quoted for radio and instrument front ends, typically where: A mixer is quoted with the SUPERB PCB and the SUPERB PCBA build for the same radio board, so the laminate, the balun and the port match are reviewed with the part.
Point to point and microwave links – a 6 GHz to 11 GHz link uses a passive mixer with 0 dBm of local oscillator drive and a differential intermediate frequency, which is the LTC5548 case in a compact radio head.
Receivers with a wide blocking requirement – a receiver that has to survive a strong nearby transmitter needs an intercept well above the wanted signal, which is why the active mixer with an integrated buffer is used at the first conversion.
Transmit chains and vector signal sources – a transmitter or a signal generator builds the modulated carrier with an IQ modulator, and the sideband suppression and carrier leakage set the error vector magnitude that can be reached.
Sourcing and Cross-Reference
A mixer is specified by numbers that only apply at one frequency and one drive level, so a replacement is checked at the frequency the radio actually uses. Conversion loss, intercept, local oscillator drive and port impedance all move across the band, and a part that looks identical on the first page of a data sheet can need 3 dB more drive or present a different intermediate frequency impedance. We quote the frequency range, the conversion loss, the intercept, the drive level and the package on every line, and the port match is checked against the filter that follows.
Where a part is out of stock, the intermediate frequency port is usually what decides the alternative: a differential port needs a balun, a single ended port does not, and the balun changes the loss and the bandwidth of the stage. We quote the mixer, the balun and the intermediate frequency filter as one set for a conversion stage, so the loss budget in the radio is calculated on parts that will be fitted.
For boards that carry a 24 lead LFCSP with an exposed pad, SUPERB Assembly support covers the reflow, the via fill under the pad and the inspection of the ground joints.
Q: Can you supply a mixer that keeps the same local oscillator drive level and port impedance?
A: Yes. Send the radio and intermediate frequencies, the local oscillator power and the intercept the blocking test needs, and the SUPERB Tech sales team will confirm the order code and the nearest part with the same port impedance.
Why Buyers Source RF Mixers Through SUPERB
- Performance quoted at the working frequency: conversion loss and intercept are stated at the band the radio uses, not only at the reference point in the data sheet.
- Port impedance checked: the intermediate frequency port and its balun are quoted with the mixer, so the loss budget belongs to parts that will be fitted.
- Radio frequency assembly support: laminate, balun and ground via placement are reviewed on the assembled board, which is where a mixer stage usually loses its match.
- Long lifecycle supply: parts a radio was qualified around are held with date codes while an alternative is measured on the bench.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Frequency converters and sources, VCO and PLL synthesizers, SAW filters and duplexers, RF transceiver ICs, RF gain blocks and LNAs, RF component sourcing.