Contact Us

MEMS Microphones for Voice and Acoustic Sensing

Digital and analog MEMS microphones in bottom port and top port packages. Signal to noise ratio from 64 dB to 70 dB, acoustic overload from 120 dBSPL to 130 dBSPL. PDM parts run from a clock line, I2S parts need no audio codec on the board. Sensitivity tolerances of plus or minus 1 dB keep array channels matched.
quote now

Product Specifications

Product Overview

A microphone on a control panel, a headset or a voice module has to turn sound pressure into a signal the processor can read, and the choice of interface decides how much of the audio chain sits around it. A PDM part outputs a single bit stream that the application processor filters in software, so the only external parts are a clock and a decoupling capacitor. An I2S part does the decimation inside the package and sends 24 bit samples over a standard serial bus. An analog part hands a small voltage to an external converter, which is still the shortest path when the board already has a codec with a spare input.

Two numbers decide whether a part fits. Signal to noise ratio sets the quietest sound the microphone can resolve, and the acoustic overload point sets the loudest before the output clips. A part with 64 dB of signal to noise ratio has an equivalent noise floor near 30 dBSPL, which is fine for speech at one metre. A part with 69 dB gets the noise floor down to about 25 dBSPL and keeps total harmonic distortion under 1 percent up to 128 dBSPL, which is what a machine monitoring point or a hands free module in a noisy room needs.

The parts on this page split along that line. The IM69D130 is the high headroom PDM option at 69 dB and 130 dBSPL, with sensitivity matched to plus or minus 1 dB and phase matched to plus or minus 2 degrees at 1 kHz so that a pair can be beamformed without calibration. The ICS-40720 is the analog differential option at 70 dB and 124 dBSPL, in a 4 mm by 3 mm package that suits a long cable run to a remote converter. The MP34DT05-A and the SPH0641LU4H-1 cover the general PDM case from 1.6 V to 3.6 V, and the SPH0645LM4H-B and the ICS-43434 are the I2S options for boards that take a serial audio input directly.

Key Specifications

ParameterPDM digitalI2S digitalAnalog differential
Signal to noise ratio64 dB(A) to 69 dB(A)65 dB(A)70 dB(A)
Acoustic overload point120 dBSPL to 130 dBSPL at 10 percent THD120 dBSPL124 dBSPL
Sensitivityminus 36 dBFS plus or minus 1 dB on IM69D130; minus 26 dBFS plus or minus 3 dB on MP34DT05-Aminus 26 dBFS plus or minus 1 dBminus 32 dBV differential, minus 38 dBV single ended
Output formatSingle bit pulse density, clock 0.768 MHz to 3.072 MHz24 bit I2S, 60 Hz to 20 kHzDifferential voltage, 75 Hz to 20 kHz
Supply voltage1.6 V to 3.6 V1.6 V to 3.6 V1.8 V nominal
Supply current235 uA in low power mode to 845 uA in ultrasonic mode490 uA typical285 uA typical
Low frequency cutoff28 Hz on IM69D13060 Hz75 Hz
Port locationBottom port and top portBottom portBottom port
Package footprint3.5 mm by 2.65 mm by 0.98 mm and 4 mm by 3 mm by 1.2 mm3.5 mm by 2.65 mm by 0.98 mm4 mm by 3 mm by 1.2 mm

Included Models and Order Codes

Order codes below are the ones quoted most often for intercoms, headsets, acoustic monitoring nodes and voice modules. State the interface, the supply rail, the port location on the board and the loudest sound the point has to survive, and the part, the sensitivity grade and the packing are confirmed.

Part NumberOutput TypeSNRAOPSupply Voltage
IM69D130V01XTSA1PDM69 dB(A)130 dBSPL1.8 V nominal
SPH0641LU4H-1PDM64.3 dB(A)120 dBSPL1.62 V to 3.6 V
MP34DT05-APDM64 dB(A)122.5 dBSPL1.6 V to 3.6 V
MP34DT05TR-APDM64 dB(A)122.5 dBSPL1.6 V to 3.6 V
SPH0645LM4H-BI2S, 24 bit65 dB(A)120 dBSPL1.6 V to 3.6 V
ICS-43434I2S, 24 bit65 dB(A)120 dBSPL1.8 V nominal
ICS-40720Analog differential70 dB(A)124 dBSPL1.8 V nominal

Key Features

Headroom for loud rooms – the IM69D130 keeps distortion under 1 percent at 128 dBSPL and overloads at 130 dBSPL, so a panel mounted beside a compressor does not clip when the machine starts.

Matched pairs for arrays – sensitivity is held to plus or minus 1 dB and phase to plus or minus 2 degrees at 1 kHz, which removes the per channel calibration step from a two microphone beamforming build.

Lowest noise in the range – the ICS-40720 reaches 70 dB(A) with an equivalent input noise of 24 dB(A), which is the margin needed to pick a failing bearing out of background noise.

No codec on the board – the I2S parts deliver 24 bit samples directly to the processor, and the PDM parts need only a clock line, so the audio path costs no extra converter and no analog routing.

Power modes set by the clock – PDM parts trade current for bandwidth with the input clock, from 235 uA in low power mode up to 845 uA in ultrasonic mode, which suits a battery node that wakes on a sound event.

Sealed against wash and dust – bottom port parts take a gasket around the acoustic hole, so the housing can be washed and the microphone stays behind the seal.

Applications

These parts are quoted for boards that capture speech or machine sound in a fixed installation, typically where: The microphone usually arrives as part of an assembly, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for the same panel or headset board.

Intercoms and access panels – a door station needs 65 dB or better with a 120 dBSPL overload so that a handset held close to the grille does not distort, and a PDM part keeps the wiring to the main board to three lines.

Headsets and voice modules – a boom arm has a small board behind the capsule, so the 3.5 mm by 2.65 mm footprint and the 1.8 V supply matter more than the last 2 dB of signal to noise ratio.

Machine condition monitoring – a vibration or bearing fault shows up as energy above 10 kHz, which is why the wider bandwidth and the 130 dBSPL headroom of the IM69D130 are used at these points instead of a speech part.

Sourcing and Cross-Reference

A microphone is rarely replaced on its own. The port location, the gasket, the clock source and the filter coefficients in the host firmware all belong to the part that was qualified, so a cross reference has to hold the interface, the sensitivity, the polarity of the clock edge and the port position at the same time. A PDM part with a different sensitivity slope will change the level in the recorded file even when the pinout is identical, and an I2S part with a different word length will shift every sample the host reads.

Status is the other half of the question. The ICS-43434 carries an end of life notice, so boards still using it are moved to the PDM parts or to the SPH0645LM4H-B, and the change is checked against the firmware filter rather than only the footprint. We quote the interface, the sensitivity grade, the port location, the supply range and the packing on every line, and we hold the original part alongside the alternative while the new one is qualified.

For volume builds, SUPERB Assembly support covers the placement of the bottom port package and the acoustic gasket check after reflow.

Q: Can you supply a drop in replacement when the microphone on our board goes end of life?

A: Yes. Send the current part number, the interface, the supply rail and the port location, and the SUPERB Tech sales team will confirm the order code and the nearest part that keeps the same clock scheme and footprint.

Why Buyers Source MEMS Microphones Through SUPERB

  1. Interface stated on the quote: PDM, I2S or analog, with the clock range and the word length, so the part matches the firmware rather than only the land pattern.
  2. Sensitivity grade held: the tolerance band is quoted per line, which is what keeps the channels of an array matched after a supplier change.
  3. End of life cover: parts under an end of life notice are flagged with the alternative that keeps the same acoustic hole and supply, so a running product is not stopped.
  4. Acoustic assembly support: the gasket and the port clearance are checked on the assembled board, not only at the component level.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Sensors and detectors, MEMS accelerometers, Temperature and humidity sensors, Audio codecs, Pin to pin cross reference.