Analog Switches and Multiplexers for Signal Routing
Product Specifications
Product Overview
A data acquisition board rarely has one converter per channel. Eight thermocouples, four bridge sensors or a set of reference taps are switched into one ADC, and the part that does the switching has to keep the signal intact while it does so. An analog multiplexer is that part: a set of CMOS switches with a binary address, an enable pin and an on resistance low enough that the source impedance and the converter input do not form a divider.
On resistance is the first number to check, and so is its flatness. The ADG1608 gives 4.5 ohms typical and 8 ohms maximum over temperature, with 1 ohm of flatness across the signal range, which means a 10 kohm source sees a gain error that moves by a small fraction over the input span rather than a curve. It runs from plus or minus 3.3 V to plus or minus 8 V dual or 3.3 V to 16 V single, passes 470 mA of continuous channel current, and holds total harmonic distortion plus noise at 0.04 percent. The ADG1408 uses the same eight to one arrangement with 5 ohms and a plus or minus 15 V range, and the ADG1609 and the ADG1409 are the four channel differential versions for bridge and thermocouple pairs.
Where the board is 3.3 V or 5 V only, the choices change. The TMUX1108 is an eight to one part with 2.5 ohms of on resistance, 3 pA of leakage and 1 pC of charge injection, in a TSSOP-16 that takes 1.8 V logic, which suits a converter with a high input impedance and a sample rate in the hundreds of kilosamples. The CD74HC4051 family is the long running general purpose option at 70 ohms on a 4.5 V supply, with the 4052 and the 4053 covering four differential and three single pole double throw channels, and it is still the cheapest way to add eight channels to a microcontroller that has one.
Key Specifications
| Parameter | Precision multiplexers | General purpose multiplexers |
|---|---|---|
| Configuration | 8 to 1 single ended on ADG1608, ADG1408 and TMUX1108; 4 differential on ADG1609 and ADG1409 | 8 to 1, 4 differential and 3 single pole double throw on the 4051, 4052 and 4053 |
| On resistance | 2.5 ohm on TMUX1108, 4.5 ohm typical and 8 ohm maximum on ADG1608, 5 ohm on ADG1408 | 70 ohm typical at 4.5 V, 40 ohm typical at 9 V |
| On resistance flatness | 1 ohm across the signal range on ADG1608 | Not specified to the same level |
| Supply range | Plus or minus 3.3 V to plus or minus 8 V dual, 3.3 V to 16 V single; 5 V or plus or minus 2.5 V on TMUX1108 | Plus or minus 5 V maximum analog input, 2 V to 6 V logic supply |
| Logic compatibility | 3 V logic on ADG1608, 1.8 V logic on TMUX1108 | CMOS and TTL thresholds depending on the version |
| Leakage | 3 pA on TMUX1108 | Not specified to the same level |
| Charge injection | 1 pC on TMUX1108 | Higher, driven by the larger switch geometry |
| Switching | Break before make, enable pin on all parts | Break before make, enable pin on all parts |
| Package | TSSOP-16, LFCSP | SOIC-16, TSSOP-16 |
Included Models and Order Codes
The codes below cover data acquisition front ends, calibration banks and signal routing on instrument boards. State the channel count, the source impedance, the signal range, the supply rails and the logic level of the controller, and the part and the package are confirmed.
| Part Number | Configuration | Channels | On Resistance | Supply | Package |
|---|---|---|---|---|---|
| ADG1608BRUZ | 8 to 1 single ended | 8 | 4.5 ohm typical, 8 ohm maximum | Plus or minus 5 V, 12 V, 3.3 V | TSSOP-16 |
| ADG1609BRUZ | 4 differential | 4 pairs | 4.5 ohm typical, 8 ohm maximum | Plus or minus 5 V, 12 V, 3.3 V | TSSOP-16 |
| ADG1408YRUZ | 8 to 1 single ended | 8 | 5 ohm | Plus or minus 15 V | TSSOP-16 |
| ADG1409YRUZ | 4 differential | 4 pairs | 5 ohm | Plus or minus 15 V | TSSOP-16 |
| TMUX1108PWR | 8 to 1 single ended | 8 | 2.5 ohm | 5 V, plus or minus 2.5 V | TSSOP-16 |
| CD74HC4051M96 | 8 to 1 single ended | 8 | 70 ohm at 4.5 V | Plus or minus 5 V maximum | SOIC-16 |
| CD74HC4052M96 | 4 differential | 4 pairs | 70 ohm at 4.5 V | Plus or minus 5 V maximum | SOIC-16 |
| CD74HC4053M96 | 3 single pole double throw | 3 | 70 ohm at 4.5 V | Plus or minus 5 V maximum | SOIC-16 |
Key Features
Flat on resistance – 1 ohm of flatness on the ADG1608 keeps the gain error steady across the input span, which matters when eight channels share one gain calibration.
Low leakage for high impedance sources – 3 pA of leakage on the TMUX1108 means a pH electrode or a 10 megohm bridge does not develop an offset across the switch while it is off.
Charge injection kept small – 1 pC on the TMUX1108 limits the step that appears on the sample capacitor when the channel changes, so a converter with a small input capacitor settles in one sample.
Dual supply for bipolar signals – plus or minus 15 V on the ADG1408 passes a plus or minus 10 V transducer signal without clipping, which a 5 V only part cannot do.
Break before make – every part on the page breaks the old channel before it makes the new one, so two sources are never shorted together during a channel change.
Enable pin on every package – the whole array can be disconnected from the converter with one logic line, which is what a self test or a calibration short needs.
Applications
These parts are quoted for boards that switch several analog sources into one converter, typically where: A multiplexer is quoted with the SUPERB PCB and the SUPERB PCBA build for the same acquisition board, so the switch, the input filter and the converter are checked as one channel.
Data acquisition and logger boards – eight thermocouples or 4 mA to 20 mA loops share one 24 bit converter, and the switch has to keep the cold junction and the lead resistance from showing up as a channel offset.
Calibration and self test banks – an instrument switches a reference divider into the converter input at power up, and the switch leakage has to be low enough that the reading is the reference and not the switch.
Signal routing in medical and test equipment – a patient monitor or a bench meter routes electrodes or probes to one front end, and the channel change has to settle before the next conversion starts.
Sourcing and Cross-Reference
An analog switch is chosen on four numbers that a pinout does not show: the on resistance, the flatness, the leakage and the charge injection. Two parts that share a TSSOP-16 footprint can differ by a factor of twenty in on resistance, which changes the gain error of a high impedance source and the settling of a switched capacitor converter. The address coding and the enable polarity also differ between families, so a replacement is checked against the firmware that drives the address lines.
Where a board is being reworked for a supply change, the switch is often the part that has to move with it. A part rated to plus or minus 15 V will not pass the same signal on a 5 V rail, and a 5 V part will not survive the bipolar signal that the old one handled. We quote the configuration, the on resistance, the supply range, the logic level and the package on every line, and the settling time is checked against the converter that follows.
SUPERB Assembly support covers the reflow of the TSSOP and SOIC parts and the cleaning that keeps flux residue away from the high impedance switch pins.
Q: Can you supply a multiplexer that keeps the same address coding and enable polarity?
A: Yes. Send the channel count, the source impedance, the signal range and the logic level, and the SUPERB Tech sales team will confirm the order code and the nearest part with the same address coding.
Why Buyers Source Analog Multiplexers Through SUPERB
- Switch and converter quoted together: the on resistance, the source impedance and the converter input are checked as one channel, so the settling time is not an estimate.
- Leakage on the quote: leakage and charge injection are stated per line, which is what a high impedance channel depends on.
- Address coding confirmed: the binary coding and the enable polarity are checked against the firmware before the part is ordered.
- Mixed supply boards supported: dual supply and single supply parts are quoted against the rails that exist, so the switch is not the part that limits the signal range.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Multi-function ICs, Logic level shifters and IO expanders, 16 bit SAR ADCs, 24 bit delta-sigma ADCs, Pin to pin cross reference.