SAW Filters and Duplexers for RF Front Ends
Product Specifications
Product Overview
A SAW filter is chosen on three numbers and one band plan. The insertion loss sets the noise figure of a receiver, the rejection at the interfering band sets whether the front end survives a nearby transmitter, and the package sets whether the part fits between the antenna and the low noise amplifier. The band plan decides everything else, because a filter that is 0.75 dB inside the GNSS band and 38 dB down at 960 MHz is only useful if the product's own radio transmits somewhere in that range.
The GNSS group on this page covers the 1575.42 MHz band with three different trade offs. The B7839 is the smallest, 2.0 by 1.4 mm, with 0.75 dB typical insertion loss, 0.05 dB of ripple and 38 dB of minimum rejection below 960 MHz. The B9444 is smaller still at 1.4 by 1.1 mm with 0.9 dB typical and a 2 MHz passband, which is the shape used in a wearable or a tracker where the antenna is inches away. The B3520 is the automotive part, in a hermetic ceramic package rated to 105 C, with 1.3 dB typical loss and no matching network needed at 50 ohms.
The duplexer group is for infrastructure rather than handsets. The QPQ6108 is a temperature compensated SAW duplexer for Band 8, 880 to 915 MHz on the uplink and 925 to 960 MHz on the downlink, with 3.2 and 3.5 dB of insertion loss, 29 dBm of downlink power handling and a 2.0 by 2.5 mm package, aimed at small cells. The QPQ1297 is a BAW duplexer for Band 3, 1710 to 1785 MHz, with 1.6 to 2.3 dB typical loss, 75 MHz of bandwidth on each side, no external matching and a 2.0 by 2.5 mm package, which is the part used in repeaters and routers where the selectivity has to hold at the band edges.
Key Specifications
| Parameter | GNSS SAW filters | Cellular duplexers |
|---|---|---|
| Band | 1575.42 MHz GPS and GNSS | Band 8 at 880 to 960 MHz, Band 3 at 1710 to 1785 MHz |
| Insertion loss | 0.75 to 1.3 dB typical | 1.6 to 3.5 dB depending on band and side |
| Passband | 2.0 to 2.4 MHz | 35 to 75 MHz |
| Rejection | 38 to 41 dB below 960 MHz, 35 dB to 6 GHz | 44 dB minimum into the transmit band |
| Power handling | 0 dBm, receive only | 29 dBm downlink on the QPQ6108 |
| Impedance | 50 ohms, unbalanced to unbalanced | 50 ohms single ended, no external matching |
| Temperature | -40 to 85 C, -40 to 105 C on the B3520 | -40 to 95 C on the QPQ1297 |
| Package | 1.4 by 1.1 mm to 2.5 by 2.0 mm | 2.0 by 2.5 mm, 9 pad SMP |
Included Models and Order Codes
The table lists the order codes most often quoted for GNSS receivers, small cells and repeaters. State the band, the passband width, the rejection needed at the interfering frequency, the power the part has to pass and the board area available, and the part and its packing are confirmed.
| Part Number | Function | Frequency | Insertion Loss | Rejection | Package |
|---|---|---|---|---|---|
| B39162-B3520-U410 | GPS SAW filter, automotive | 1575.42 MHz, 2.4 MHz passband | 1.3 dB typical, 1.8 dB maximum | 40 dB below 1450 MHz | Ceramic DCC6C, 3 by 3 mm |
| B7839 | GPS SAW filter | 1575.42 MHz, 2.0 MHz passband | 0.75 dB typical, 1.1 dB maximum | 38 dB minimum below 960 MHz | QCS5E, 2.0 by 1.4 mm |
| B9444 | GPS SAW filter | 1575.42 MHz, 2.0 MHz passband | 0.9 dB typical, 1.3 dB maximum | 40 dB at 880 to 915 MHz | QCS5I, 1.4 by 1.1 mm |
| B7742 | GPS extractor filter | 1575.42 MHz plus cellular bypass | Low loss in the GPS path | High selectivity on the GPS output | DCS6N, 2.5 by 2.0 mm |
| QPQ6108 | Band 8 TC-SAW duplexer | 880 to 915 MHz uplink, 925 to 960 MHz downlink | 3.2 and 3.5 dB typical | High rejection, 29 dBm downlink | SMP 9 pad, 2.0 by 2.5 mm |
| QPQ1297 | Band 3 BAW duplexer | 1710 to 1785 MHz, 75 MHz bandwidth | 1.6 to 2.3 dB typical, 4.1 dB maximum | 44 dB minimum into 1805 to 1880 MHz | SMP 9 pad, 2.0 by 2.5 mm |
Key Features
Loss quoted inside the passband – a typical and a maximum are given over the passband rather than at the centre frequency, because the edge is where a receiver actually works.
Rejection against real interferers – the attenuation is stated against the cellular, PCS and WLAN bands that sit near the GNSS band, not as a single stopband figure.
Temperature compensation – a TC-SAW duplexer holds its band edges over temperature, which is what keeps a small cell inside the 3GPP mask at 85 C.
No external matching – the duplexers and the B3520 are specified at 50 ohms without a matching network, which removes six components and a tuning step.
Small packages – a 1.4 by 1.1 mm filter fits beside the antenna in a tracker, and a 2 by 2.5 mm duplexer leaves room for the PA and the switch on a small cell board.
Hermetic options – the ceramic package is rated to 105 C and holds its loss over life, which is what an automotive telematics unit needs.
Applications
These filters are quoted for receivers and front ends that share an antenna, typically where: An RF front end board is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same assembly, so the filters, the switch and the shielding arrive as one order.
GNSS receivers and trackers – a 1575.42 MHz filter with 38 dB of rejection below 960 MHz keeps a cellular transmitter from desensing the receiver on a device that has both radios.
Small cells and repeaters – a Band 8 or Band 3 duplexer has to hold its isolation and its band edges at full transmit power and over temperature, which is what the TC-SAW and BAW parts are specified for.
Telematics and fleet units – an automotive grade filter with a 105 C rating and no matching network survives the thermal and vibration profile of a unit mounted in an engine bay.
Sourcing and Cross-Reference
Filter parts are band specific and are not interchangeable across bands, even when the package and the pinout match. A Band 8 duplexer in a Band 5 socket will pass a signal and will fail the emissions test, and a GNSS filter with a wider passband will admit the interference the narrow one was selected to reject. We quote the band, the passband, the rejection at the named interferer and the maximum loss on the confirmation, so a replacement is checked against the band plan.
The board around the filter decides the measured performance. A 50 ohm launch, a ground via at each ground pad, no trace under the package and a keep out around the antenna are all part of the specification, and a filter that is 0.75 dB on the datasheet can read 1.5 dB on a board that treats it as a three terminal part. We quote the filter with the matching components where they are needed and review the launch before the first panel.
Where the front end boards are built in volume, SUPERB Assembly support covers the placement of the 1.4 mm filters and the reflow profile that the ceramic packages need.
Q: Can you supply a GNSS SAW filter and a Band 8 duplexer from one order?
A: Yes. Send the band, the passband width, the rejection needed at the interfering frequency and the board area, and the SUPERB Tech sales team will confirm the order code, the packing and the matching components where they are needed.
Why Buyers Source SAW Filters Through SUPERB
- Band plan on the quote: the uplink and downlink windows, the passband and the rejection at the named interferer are stated per line, so the part matches the radio it will sit behind.
- Loss at the band edge: the maximum insertion loss is quoted over the passband, which is the number that decides the receiver noise figure.
- Package and matching: the footprint, the ground pads and the matching components are quoted together, so the measured loss is the one that was specified.
- Lifecycle supply: parts that a product was qualified around are held with date codes, which keeps a tracker or a small cell in production while an alternative is characterised.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Frequency converters and sources, RF transceiver ICs, RF gain blocks and LNAs, VCO and PLL synthesizers, RF component sourcing.