Contact Us

Charge Pump Regulators and Inverting Converters

Switched capacitor inverters, doublers and regulated charge pumps from 1.6 V to 38 V input. Output current runs from 10 mA on the smallest parts to 250 mA on the regulated dual output parts. Oscillator frequency and package are listed per row, with the regulation method named. Parts that keep the ICL7660 pinout are marked, because that footprint still appears on old boards.
quote now

Product Specifications

Product Overview

A charge pump makes a negative rail without an inductor. Two capacitors, four internal switches and an oscillator move charge from the input to a flying capacitor and then to the output, which gives a negative voltage close to the input, or twice the input if the same parts are connected as a doubler. The price is a limited output current and an output that sags under load, and the gain is a solution that fits under a connector and radiates far less than a switching regulator.

The first decision is unregulated or regulated. An unregulated part such as the LM2776 or the TPS60403 gives roughly minus VIN into a light load and needs no feedback parts; it is the right choice for an op amp negative rail that only has to sit near -5 V. A regulated part such as the MAX889 or the LT1054 holds the output against input and load changes, because it compares the output with a reference and adjusts the switch resistance. Regulated parts cost more pins and need a divider, and they are what a data converter or a bipolar sensor front end asks for.

The second decision is how much current at what frequency. A 10 mA part in a SOT-23 is enough for a comparator reference; 100 mA to 250 mA is what a dual op amp or a small display bias needs, and those parts run at 250 kHz to 2 MHz so the flying capacitor can be 1 µF ceramic. Higher input voltage is a separate family: the LTC3260 takes 4.5 V to 32 V and adds a positive and a negative LDO after the pump, and the LTC3245 takes 2.7 V to 38 V and works as a charge pump buck-boost for a 12 V to 5 V rail.

Layout matters more than the part number here. The flying capacitor carries the full switch current, so it belongs on the same side of the board as the IC with a short return, and the output capacitor is what holds the rail during the switch interval. A long trace to the flying capacitor turns a quiet pump into a radiator at the oscillator frequency, and no part choice fixes that.

Key Specifications

ParameterUnregulated inverterRegulated inverting pumpDual polarity pump
Typical partsLM2776, TPS60400 to TPS60403, MAX1044MAX889, LT1054LM27762, LTC3260, LTC3245
Input range1.5 V to 10 V depending on part2.7 V to 15 V2.7 V to 38 V
Outputabout minus VIN, or 2 x VIN as a doubleradjustable negative, regulatedpositive and negative rails, or a fixed 3.3 V and 5 V rail
Output current10 mA to 200 mA100 mA to 200 mA50 mA per LDO to 250 mA
Oscillator10 kHz to 2 MHz, fixed per part25 kHz to 2 MHz, adjustable or synchronizable50 kHz to 2 MHz
Regulation methodnone, output follows the loadreference and error amplifier inside the partpump plus LDO post regulator
PackageSOT-23-5, SOT-23-6, µMAX-8, SO-8SO-8, SW16WSON-12, MSOP-12, MSOP-16, DFN-12, DFN-14
Pin compatible with ICL7660MAX1044, LT1054, ADM8660LT1054not applicable

Included Models and Order Codes

The rows below are the parts quoted most often for op amp negative rails, sensor front ends, display bias and 12 V to 5 V housekeeping. Give the input rail, the output voltage and current, and whether the output has to stay regulated, and the part, the flying capacitor value and the package are confirmed.

Part NumberFunctionInput RangeOutput CurrentOscillatorPackage
MAX1044Inverter, doubler, divider1.5 V to 10 V10 mA with 0.5 V drop10 kHz, boost pin raises itµMAX-8, SO-8, DIP-8
MAX660Inverter or doubler1.5 V to 5.5 V100 mA, 0.65 V loss10 kHz or 80 kHz selectableDIP-8, SO-8
MAX889Regulated inverting pump2.7 V to 5.5 V200 mA0.5 MHz, 1 MHz or 2 MHzSO-8
LT1054Regulated inverter, doubler3.5 V to 15 V100 mA, 1.1 V loss25 kHz, synchronizableSO-8, SW16
LM2776Unregulated inverter2.7 V to 5.5 V200 mA2 MHzSOT-23-6
LM27762Positive and negative output with LDO2.7 V to 5.5 Vplus and minus 250 mA2 MHzWSON-12
TPS60400Unregulated inverter, variable frequency1.6 V to 5.5 V60 mA20 kHz to 250 kHz, load dependentSOT-23-5
TPS60403Unregulated inverter1.6 V to 5.5 V60 mAfixed 250 kHzSOT-23-5
LTC3260Inverting pump with positive and negative LDO4.5 V to 32 V100 mA pump, 50 mA per LDO50 kHz to 500 kHzDFN-14, MSOP-16
LTC3245Charge pump buck-boost, 2:1 and 1:1 modes2.7 V to 38 V250 mAconstant frequency, mode switches automaticallyMSOP-12, DFN-12
ADM8660Inverting converter with shutdown1.5 V to 7 V100 mA25 kHz or 120 kHz selectableTSSOP-16

Key Features

No inductor, no radiated loop – the switching loop is two capacitors instead of an inductor and a diode, which is why a charge pump sits quietly next to a sensitive analog front end.

Regulated or unregulated stated – each row says whether the output is held by a reference and error amplifier or simply follows the input, because that decides whether a divider and a feedback pin appear in the bill of materials.

Current at a stated drop – the output current is given with the voltage loss that comes with it, so 100 mA at 0.65 V is not read as 100 mA at any load.

Oscillator choice per part – 10 kHz parts keep quiescent current low, 2 MHz parts allow 1 µF ceramic capacitors, and the row gives the range instead of a single nominal figure.

ICL7660 footprint marked – the MAX1044, the LT1054 and the ADM8660 keep the industry pinout, which is what allows an old board to be reworked without a layout change.

Dual rails in one package – the LM27762 and the LTC3260 produce a positive and a negative rail from one part, which is what a bipolar op amp stage or a DAC bias needs.

High voltage input parts – the LTC3260 at 32 V and the LTC3245 at 38 V cover 12 V and 24 V industrial rails where the usual 5 V pumps cannot be used.

Shutdown and power good – the ADM8660 and the LM27762 bring a shutdown pin and a power good flag, so a rail can be sequenced instead of always on.

Applications

These parts are quoted for low current bipolar rails and for housekeeping supplies, typically where: The pump sits beside the analog section on the same card, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that board.

Op amp and converter negative rails – a 5 V single supply board needs -5 V at 20 mA for an amplifier that swings below ground, and an unregulated inverter with two 1 µF capacitors does it without an inductor.

Sensor and instrumentation front ends – a bipolar bridge or a thermocouple front end needs a quiet negative rail, so a regulated pump with a following LDO keeps the switching ripple below the resolution of a 24 bit converter.

Display and RF bias – a small OLED or an RF switch needs 12 V or a negative gate bias from a 3.3 V rail, and a doubler or inverting pump with 100 mA covers it in a SOT-23 footprint.

12 V and 24 V industrial housekeeping – the LTC3245 takes 12 V down to 5 V at 250 mA without an inductor, and the LTC3260 makes plus and minus 12 V rails for an analog card from a 24 V bus.

Sourcing and Cross-Reference

Charge pump cross references depend on more than the pinout. The output resistance, the oscillator frequency and the current at a stated voltage drop decide whether a substitute holds the rail, and a part with a higher frequency needs smaller capacitors but a tighter layout. The old ICL7660 and LTC1044 pinout still appears on boards from the 1990s, and parts such as the MAX1044 and the ADM8660 keep that footprint while delivering more current.

Some of the classic parts are still active and some are not, and the difference is not always visible from a catalogue page. Where a part is at the end of its life, the practical move is a regulated pump with a similar output current and a lower output resistance, and the flying capacitor value has to be re-checked because a higher oscillator frequency with the same capacitor gives a higher ripple current.

A charge pump quotation usually includes the flying and reservoir capacitors, because the part number alone does not define the ripple. Sending the input rail, the output voltage and current and the ripple the load can accept is enough to quote a complete pump.

For volume builds, SUPERB Assembly support covers the flying capacitor placement, the short return path and the reflow profile for the small DFN and WSON packages.

Q: Can you supply a drop in charge pump for an ICL7660 or LTC1044 footprint that is no longer available?

A: Yes. Send the footprint, the input rail, the output voltage and the load current, and the SUPERB Tech sales team will confirm the part that keeps the pinout and the capacitor values.

Why Buyers Source Charge Pumps Through SUPERB

  1. Output current with its voltage drop: the current is quoted at the loss that comes with it, so a 100 mA part is not compared with a 200 mA part on unequal terms.
  2. Regulation method named: regulated and unregulated parts are separated, which decides whether a feedback divider appears in the bill of materials.
  3. Old footprints supported: the ICL7660 and LTC1044 pinout is marked on the rows that keep it, so an existing board can be reworked without a layout change.
  4. Capacitors quoted with the part: the flying and reservoir values are part of the line, because the ripple depends on them as much as on the IC.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Power management ICs, Boost and SEPIC controllers, Load switches and hot swap controllers, Battery protection ICs and BMS front ends, Pin to pin cross reference.