Contact Us
  • Home
  • COMPONENTS
  • Ferrite Beads and EMI Suppression Filters for Board Noise

Ferrite Beads and EMI Suppression Filters for Board Noise

Chip ferrite beads in 0603 and 0805 with impedance from 60 Ω to 1000 Ω at 100 MHz. Rated current from 0.5 A to 3.5 A, with DC resistance from 0.020 Ω on the high current parts. Impedance, tolerance, rated current and DC resistance are listed per part number. The DC resistance is what decides the drop on a supply rail; the impedance only works above 10 MHz.
quote now

Product Specifications

Product Overview

A ferrite bead is a lossy inductor. At low frequency it looks like a small resistance in series with the rail, and at high frequency its impedance rises and the resistive part turns the noise into heat. That is why a bead is placed in series with a supply pin or a cable, where it removes the high frequency ripple a regulator cannot regulate away, and why it is not a substitute for a capacitor: the bead blocks, the capacitor shunts.

The number on the label is impedance at 100 MHz, and it is the least useful number on its own. A 220 Ω bead with 0.10 Ω of DC resistance carries 1.4 A and drops 0.14 V at that current, while a 220 Ω bead with 0.050 Ω carries 2.2 A and drops half as much. The impedance also peaks at one frequency and falls away either side, so a bead chosen for 100 MHz may do very little at 500 MHz where the emission actually is.

The parts on this page run from 0603 beads at 0.5 A to 0603 power beads at 3.5 A, and 0805 beads at 2 A, with impedance from 60 Ω to 1000 Ω. All of them are rated to +125 C including self heating, which is the temperature that matters in a sealed enclosure. Where a bead is used on a power rail, the DC resistance drop and the current derating above 85 C are the two figures that decide whether the part can stay.

Key Specifications

Parameter0603 signal bead0603 power bead0805 power bead
Impedance at 100 MHz220 Ω to 1000 Ω60 Ω to 220 Ω220 Ω
Rated current0.5 A to 1.4 A2.0 A to 3.5 A2 A
DC resistance0.050 Ω to 0.300 Ω0.020 Ω to 0.050 Ω0.045 Ω
Impedance toleranceplus or minus 25 %plus or minus 25 %plus or minus 25 %
Operating range-55 C to +125 C-55 C to +125 C-55 C to +125 C
Derating above 85 Cper the maker curveper the maker curveper the maker curve
Case size1.6 x 0.8 mm1.6 x 0.8 mm2.0 x 1.25 mm
Best positionsignal and clock linessupply rails and DC feedssupply rails with more current

Included Models and Order Codes

The table lists the beads we quote most often. Impedance at 100 MHz, rated current, DC resistance and case size are copied from the maker data sheet for each part number. Impedance is stated at one frequency only, because the parts differ in where the impedance peaks rather than only in its height.

Part NumberCaseImpedance at 100 MHzRated CurrentDC ResistanceType
BLM18PG181SN1D0603180 Ω1.5 A0.090 ΩPower line
BLM18PG221SN1D0603220 Ω1.4 A0.100 ΩPower line
BLM18PG331SN1D0603330 Ω1.2 A0.150 ΩPower line
BLM18PG471SN1D0603470 Ω1.0 A0.200 ΩPower line
BLM18AG221SN1D0603220 Ω0.5 A0.250 ΩSignal line
BLM18KG221SN1D0603220 Ω2.2 A0.050 ΩPower line
MPZ1608S101ATAH00603100 Ω3.0 A0.030 ΩPower line
MPZ1608S600ATAH0060360 Ω3.5 A0.020 ΩPower line
MPZ1608S102ATA0006031000 Ω0.8 A0.300 ΩSignal line
BLM21PG221SN1D0805220 Ω2 A0.045 ΩPower line

Key Features

Impedance at one frequency only – a bead is specified at 100 MHz, but its impedance rises to a peak and falls again, so the frequency of the emission decides whether a 220 Ω part or a 1000 Ω part is the right one.

DC resistance sets the rail drop – 0.100 Ω at 1.4 A is 0.14 V of drop on a 3.3 V rail, which is why a power line bead at 0.030 Ω and 3 A is chosen where the current is high.

Current derating above 85 C – the rated current is quoted at 85 C and falls above it, and the rating already includes self heating, so the figure in a hot enclosure is lower than the label.

Six case and current combinations – 180 Ω to 1000 Ω in 0603 and 220 Ω in 0805, with 0.5 A to 3.5 A of current, so a rail and a signal line can be covered from one family.

Signal beads with higher impedance – the 1000 Ω 0603 part carries only 0.8 A but presents ten times the impedance of a 100 Ω part, which is what a clock or a reset line needs.

No ground connection needed – a bead sits in series with the line and needs no via to ground, which is why it fits where a filter capacitor cannot be placed close enough to the noise source.

Applications

These beads are quoted where a rail or a line carries noise that has to be absorbed, typically where: The bead sits in series with the rail on the same board, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Supply pin of an analog block – a 220 Ω 0603 bead in series with the supply of a converter or an amplifier removes the switching residue from the regulator before it reaches the reference.

DC feed to a connector – a 60 Ω to 100 Ω bead at 3 A carries the current into a cable while blocking the common mode noise the cable would otherwise radiate.

Clock and reset lines – a 1000 Ω bead on a clock or reset line removes the fast edge that couples into an adjacent trace, at the cost of 0.3 Ω of series resistance that the line can tolerate.

Sourcing and Cross-Reference

A bead is chosen on the noise frequency, the current and the drop it can afford. The frequency decides the impedance, the current decides the case and the part family, and the drop decides the DC resistance. Almost every wrong pick is a part chosen on impedance alone, then found to drop 0.2 V on a rail that could afford 0.05 V.

The second check is thermal. The rated current already includes self heating at 85 C, and the rating falls above that, so a 1.4 A part in a 105 C enclosure is derated before it is quoted. The impedance also falls with DC bias on some materials, which the maker curve shows, and the part is checked at the current it will actually carry.

Where a bead has been discontinued, the replacement is matched on impedance at the emission frequency, current, DC resistance and case size. The route for these parts is on our pin to pin cross reference page, and the cost question for a board with many beads is on how to reduce component cost.

For volume builds, SUPERB Assembly support covers the placement next to the pin it protects, the land pattern the case needs and the washing step the bead allows.

Q: Can you supply a bead with the same impedance and lower DC resistance than a discontinued part?

A: Yes. Send the emission frequency, the rail current, the drop the rail can afford and the case size, and the SUPERB Tech team will confirm which bead fits and quote it with the impedance curve for that frequency.

Why Buyers Source Ferrite Beads Through SUPERB

  1. Frequency first, impedance second: the emission frequency is matched with the impedance curve of the part, because a bead specified at 100 MHz can do little at 500 MHz.
  2. Rail drop calculated: DC resistance is multiplied by the rail current before a part is quoted, so the bead does not take the margin out of a 3.3 V rail.
  3. Thermal derating applied: the rated current is derated for the enclosure temperature and for self heating, which is where a bead on a hot rail loses its margin.
  4. Case and land pattern confirmed: 0603 and 0805 parts are checked against the pad and the clearance to the pin, so the part can be placed where it has to be.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Passive components, Common mode chokes and power inductors, MLCC and ceramic capacitors, Pin to pin cross reference.