Contact Us
  • Home
  • COMPONENTS
  • Digital Step Attenuators for RF and Instrument Signal Chains

Digital Step Attenuators for RF and Instrument Signal Chains

Silicon and GaAs step attenuators with parallel or serial control. Attenuation ranges of 7.75 dB, 31.5 dB and 31.75 dB in 0.25 dB or 0.5 dB steps. Insertion loss from 1.1 dB at 1 GHz to 4.5 dB at 40 GHz depending on the part. Glitch free transitions and monotonic steps for closed loop level control.
quote now

Product Specifications

Product Overview

A receiver or a signal generator has to hold its output at a known level across temperature, frequency and cable length, and the block that does the correction is a step attenuator. Relay attenuators still exist for high power and for dc, but a silicon or GaAs part switches in nanoseconds, needs no driver per bit, and repeats to a fraction of a decibel. The parts on this page divide into 6 bit and 0.5 dB steps for general level control, and 7 bit and 0.25 dB steps where a calibration loop needs finer resolution.

The 6 bit group covers the common radio bands. The HMC624A spans 0.1 GHz to 6 GHz with 31.5 dB in 0.5 dB steps, 1.6 dB of insertion loss at 3 GHz, 33 dBm of input compression at 3 V and 55 dBm of third order intercept, with both parallel and 3 wire serial control in a 4 mm by 4 mm LFCSP. The PE4312 covers 1 MHz to 4 GHz with 59 dBm of input intercept and 500 ns switching, and the HMC425A moves the same 0.5 dB step to 2.2 GHz to 8 GHz in a 3 mm by 3 mm package for the higher microwave bands.

The 7 bit group is for instruments and for broadband front ends. The HMC1119 gives 31.75 dB in 0.25 dB steps from 0.1 GHz to 6 GHz with 1.1 dB of loss at 1 GHz and 6 degrees of phase shift, and the PE43711 extends the same resolution down to 9 kHz with glitch free transitions and 1.8 V control logic. At the top of the range the ADRF5720 is a silicon part that reaches 40 GHz with 2.0 dB of loss to 18 GHz, 4.5 dB to 40 GHz, 27 dBm of average input power and 8 microseconds of settling, in a 4 mm by 4 mm LGA that is pin compatible with the faster ADRF5730.

Key Specifications

Parameter6 bit, 0.5 dB steps7 bit, 0.25 dB steps
Frequency range1 MHz to 8 GHz depending on part9 kHz to 40 GHz depending on part
Attenuation range31.5 dB on HMC624A, PE4312 and HMC425A31.75 dB on HMC1119 and PE43711
Step size0.5 dB, monotonic to the top of the band0.25 dB, with 0.5 dB and 1 dB modes on PE43711
Insertion loss1.6 dB at 3 GHz on HMC624A; 3.5 dB to 4.5 dB on HMC425A1.1 dB at 1 GHz on HMC1119; 2.0 dB to 18 GHz on ADRF5720
Input linearity33 dBm compression and 55 dBm intercept on HMC624A31 dBm compression and 54 dBm intercept on HMC1119; 30 dBm on ADRF5720
ControlParallel bit lines, and 3 wire serial on HMC624A and PE4312Parallel on HMC1119 and PE43711; SPI and parallel on ADRF5720
Supply3 V to 5 V single3.3 V to 5 V single; plus and minus 3.3 V on ADRF5720
Package3 mm and 4 mm LFCSP, 4 mm QFN4 mm LFCSP, 4 mm and 5 mm QFN, 4 mm LGA

Included Models and Order Codes

The table lists the order codes most often quoted for radios, test equipment and optical modules. State the band, the resolution, the control interface and the input power the part will see, and the order code and packing are confirmed.

Part NumberFrequencyBits and StepRangeInsertion LossControlPackage
HMC624ALP4E0.1 GHz to 6 GHz6 bit, 0.5 dB31.5 dB1.6 dB at 3 GHz, 2.3 dB at 6 GHzParallel and 3 wire serialLFCSP-24, 4 by 4 mm
HMC1119LP4ME0.1 GHz to 6 GHz7 bit, 0.25 dB31.75 dB1.1 dB at 1 GHz, 1.3 dB at 2 GHzParallelLFCSP-24, 4 by 4 mm
HMC425ALP3E2.2 GHz to 8 GHz6 bit, 0.5 dB31.5 dB3.5 dB from 2.2 to 6 GHz, 4.5 dB to 8 GHzSix control linesSMT-16, 3 by 3 mm
ADRF5720BCCZN9 kHz to 40 GHz6 bit, 0.5 dB31.5 dB2.0 dB to 18 GHz, 2.8 dB to 26 GHz, 4.5 dB to 40 GHzSPI and parallelLGA-24, 4 by 4 mm
PE43711B-Z9 kHz to 6 GHz7 bit, 0.25 dB31.75 dB1.3 dB to 1 GHz, 2.4 dB from 4 to 6 GHzParallel and serialQFN-24, 4 by 4 mm
PE43712B-Z9 kHz to 6 GHz7 bit, 0.25 dB31.75 dB1.30 dB to 1 GHz, 2.45 dB from 4 to 6 GHzLatched or direct parallelQFN-32, 5 by 5 mm
PE4312C-Z1 MHz to 4 GHz6 bit, 0.5 dB31.5 dB1.3 dB to 1 GHz, 2.3 dB from 2.2 to 4 GHzParallel and serialQFN-20, 4 by 4 mm

Key Features

Glitch free level changes – the PE43711 and PE4312 change state without a transient, which matters when the attenuator sits in a closed loop that would chase its own switching spike.

Monotonic steps – 0.25 dB monotonicity to 4 GHz on the PE43711 and 0.5 dB to 4 GHz on the PE4312 means a calibration table can be built once and trusted at every code.

Linearity for a transmit path – 55 dBm of third order intercept on the HMC624A and 59 dBm on the PE4312 keep the attenuator from being the compression point in front of a power stage.

Control that fits the board – parallel bit lines need no firmware, while the serial port on the HMC624A cascades several parts on one bus with a serial data output delayed by six clocks.

Coverage to 40 GHz – the ADRF5720 reaches 40 GHz in silicon with 4.5 dB of loss, which removes the per band relay attenuator from a microwave instrument.

Small packages – a 3 mm by 3 mm HMC425A or a 4 mm LGA keeps the attenuator inside a module where the connector is the tallest part.

Applications

These attenuators are quoted for boards that have to set or correct an RF level, typically where: A microwave board is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same assembly, so the attenuator, the blocking capacitors and the connector arrive together.

Signal generators and spectrum analysers – a 0.25 dB step and a monotonic table let the instrument hold its output flat across the band without a per unit calibration file.

Radio and VSAT front ends – a 6 bit part ahead of the mixer sets the gain distribution per channel, and 33 dBm of compression covers the transmit leakage that reaches it.

Optical and microwave modules – a 4 mm LGA attenuator with 8 microsecond settling fits the automatic level control loop inside a coherent module, where the loop has to follow a temperature ramp.

Sourcing and Cross-Reference

Step attenuators are often the last part of a build to be revisited, and by then the original GaAs part may be obsolete. A replacement has to match the attenuation range, the step size, the control interface, the logic level and the input power handling, and it has to keep the same relative phase behaviour or the calibration table no longer applies. We quote those five points per line, and where an exact part is gone we quote the nearest silicon alternative with the difference stated rather than hidden.

The supporting parts matter as much as the attenuator. The control lines need series resistors and a clean ground under the package, the RF ports need dc blocking where the part does not provide it, and the 0.1 dB compression figure has to be checked against the power that reaches the input in the worst case. We quote the attenuator, the blocking capacitors and the control pull ups as one set so the power and switching numbers are calculated on the board that will be built.

Where the modules are built in volume, SUPERB Assembly support covers the SMT build and the inspection of the 3 mm and 4 mm leadless packages.

Q: Can you supply an attenuator that matches an obsolete HMC or PE part, including the control interface?

A: Yes. Send the current part number, the band, the step size and the control lines you have, and the SUPERB Tech sales team will confirm the order code and the nearest part that keeps the same interface.

Why Buyers Source Step Attenuators Through SUPERB

  1. Range and step on the quote: the frequency band, the bit count, the step size and the input compression are stated per line, so the part matches the level plan rather than only the footprint.
  2. Interface checked before shipping: parallel, latched parallel and serial parts are not interchangeable, and the control scheme is confirmed against the driver before the order is released.
  3. RF assembly experience: leadless packages with an exposed pad are placed and reflowed on the same line that supplies them, which keeps ground and thermal voids visible.
  4. Lifecycle cover: parts that a module was calibrated around are held with date codes, so production continues while an alternative is qualified.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Frequency converters and sources, RF switches and PIN diode switches, VCO and PLL synthesizers, RF transceiver ICs, RF component sourcing, Obsolete RF part replacement.