Contact Us
  • Home
  • COMPONENTS
  • PIN Photodiodes and Avalanche Photodiodes for Optical Receivers

PIN Photodiodes and Avalanche Photodiodes for Optical Receivers

Silicon PIN photodiodes covering 320 nm to 1100 nm, with bandwidth from 20 MHz to 1 GHz. InGaAs PIN parts for 0.9 um to 2.6 um, and an InGaAs avalanche part for 1000 nm to 1700 nm. Responsivity, dark current, capacitance and cutoff frequency are listed per part number. Active area and package are quoted with the part, because both set the bandwidth.
quote now

Product Specifications

Product Overview

A photodiode turns light into current, and the two families on this page do it at opposite ends of the spectrum. A silicon PIN part covers 320 nm to 1100 nm, which is where visible light, 850 nm data links and most industrial sensing sit. An InGaAs part covers 0.9 um to 2.6 um, which is where 1310 nm and 1550 nm telecom signals and most gas sensing lines sit.

The choice inside a family is a trade between area, capacitance and speed. A 1.2 mm silicon part has 3 pF and reaches 100 MHz, while a 0.4 mm part with a lens has 1.6 pF and reaches 1 GHz, but it collects far less light. An InGaAs part with a 1 mm area has 500 pF and 6 MHz, which suits a power meter, while an 80 um avalanche part has 1.25 pF and 1 GHz with internal gain of 10, which suits a receiver front end.

Dark current and responsivity are the other two numbers. Dark current sets the noise floor and rises with temperature and with reverse bias, and responsivity sets how much current a given optical power produces: 0.55 A/W at 780 nm on a silicon part, 1.3 A/W at 2.3 um on an InGaAs part, and 9.3 A/W at 1550 nm on an avalanche part running at gain 10. Every part in the table is listed with the reverse voltage at which those figures apply, because they move with bias.

Key Specifications

ParameterSilicon PINInGaAs PINInGaAs avalanche
Spectral range320 nm to 1100 nm0.9 um to 2.6 um1000 nm to 1700 nm
Responsivity0.55 A/W to 0.62 A/W at 780 to 850 nm1.3 A/W at 2.3 um9.3 A/W at 1550 nm, gain 10
Active area0.12 mm2 to 1.1 mm20.07 mm2 to 7 mm280 um diameter
Capacitance1.6 pF to 72 pF40 pF to 500 pF1.25 pF
Dark current0.1 nA to 2 nA typical4 uA to 30 uA max2.5 nA to 15 nA at gain 10
Bandwidth20 MHz to 1 GHz6 MHz to 75 MHz1000 MHz
Reverse voltage5 V to 20 V max0.5 V to 1 V bias45 V to 70 V breakdown
PackageTO-18, DIL plasticTO-18, TE cooled optionTO-18, ceramic

Included Models and Order Codes

The table lists the photodiodes we quote most often. Spectral range, responsivity, active area, dark current, capacitance and cutoff frequency are copied from the maker data sheet for each part number, with the measurement bias stated in the text where the figure depends on it.

Part NumberTypeSpectral RangeResponsivityActive AreaBandwidth
S5971Si PIN, TO-18320 to 1060 nm0.55 A/W at 780 nmφ1.2 mm, 1.1 mm2100 MHz
S5972Si PIN, TO-18320 to 1060 nm0.57 A/W at 780 nmφ0.8 mm, 0.5 mm2400 MHz
S5973-01Si PIN, lens TO-18320 to 1000 nm0.51 A/W at 780 nmφ0.4 mm, 0.12 mm21000 MHz
BPW34Si PIN, DIL plastic400 to 1100 nm0.62 A/W at 850 nm2.65 x 2.65 mm20 ns rise time
G12183-010KInGaAs PIN, TO-180.9 to 2.6 um1.3 A/W at 2.3 umφ1.0 mm6 MHz
C30645EInGaAs APD, TO-181000 to 1700 nm9.3 A/W at 1550 nm, M=10φ80 um1000 MHz

Key Features

Area against bandwidth – the 1.2 mm silicon part has 3 pF and 100 MHz, the 0.4 mm lens part has 1.6 pF and 1 GHz, and the light collected falls with the area, so the two are chosen together.

Responsivity at the working wavelength – 0.55 A/W at 780 nm on silicon, 0.62 A/W at 850 nm on the plastic part and 1.3 A/W at 2.3 um on InGaAs, which sets the current for a given optical power.

Dark current sets the noise floor – 0.1 nA typical on the small silicon part against 30 uA max on the 1 mm InGaAs part, and the difference decides whether a transimpedance stage can resolve a small signal.

Avalanche gain inside the part – the APD multiplies the photocurrent by 10 at 45 V to 70 V of bias, which lifts 0.9 A/W of primary responsivity to 9.3 A/W at 1550 nm.

Capacitance quoted with bias – terminal capacitance is measured at a stated reverse voltage, and it falls as the bias rises, which is why the bias is part of the specification.

Packages that fit an optical bench – TO-18 metal cans with and without a lens, a DIL plastic part for a through hole board, and a ceramic package option on the avalanche part.

Applications

These photodiodes are quoted at the front of an optical receiver or a light measurement path, typically where: The photodiode sits at the optical interface on the same board as the transimpedance stage, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Optical receiver front end – an InGaAs PIN or avalanche part converts 1310 nm or 1550 nm light into current for a transimpedance amplifier, and the capacitance and bandwidth are chosen against the data rate.

Optical power meter and gas sensing – a 1 mm InGaAs part with 1.3 A/W at 2.3 um measures absolute optical power, where a large area matters more than speed.

Industrial sensing and encoders – a silicon part with 0.62 A/W at 850 nm and a 20 ns rise time detects a beam, a mark or a reflection, and the plastic package fits a through hole board.

Sourcing and Cross-Reference

A photodiode is chosen from the light, not from the part list. The wavelength sets the material, the optical power and the required signal to noise set the area and the dark current, and the data rate sets the capacitance and the bandwidth. A part that meets the bandwidth but has a tenth of the area collects a tenth of the light, and the receiver then needs more gain and pays for it in noise.

The second half is the bias and the package. Responsivity, dark current and capacitance are all quoted at a stated reverse voltage, and an avalanche part needs a bias within a few volts of its breakdown, which means a temperature compensated supply. The package decides the coupling: a lens can on a fibre, a flat window on a free space path, and the pin out has to match the board.

Where a part has been discontinued, the replacement is matched on spectral range, active area, responsivity, capacitance and package. The route for these parts is on our obsolete part cross reference hub, and the replacement check for a drop in part is on how to verify a drop in replacement.

For volume builds, SUPERB Assembly support covers the can placement, the bias decoupling beside the cathode and the shielding the small photocurrent needs.

Q: Can you supply a photodiode with the same active area and package as a part that is no longer produced?

A: Yes. Send the wavelength, the optical power, the data rate, the active area, the package and the pin out, and the SUPERB Tech team will confirm which part fits and quote it with the responsivity and dark current at the bias you use.

Why Buyers Source Photodiodes Through SUPERB

  1. Wavelength and material matched: silicon is offered for 320 nm to 1100 nm and InGaAs for 0.9 um to 2.6 um, so the part is chosen on the light rather than on the package.
  2. Area and bandwidth traded openly: the active area, capacitance and cutoff frequency are quoted together, so the loss of collected light is visible before the part is chosen.
  3. Bias stated with the figures: responsivity, dark current and capacitance are given at the reverse voltage they were measured at, which is where most substitution errors start.
  4. Package and pin out confirmed: can type, window or lens and pin arrangement are checked against the board, because an optical part with the wrong window cannot be corrected on the board.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Sensors and detectors, Transimpedance amplifier chips, Limiting amplifier chips, Obsolete part cross reference hub.