USB Hubs and Port Controllers for Embedded Hosts
Product Specifications
Product Overview
An embedded board usually has one host port and several things that need to be plugged in: a keyboard, a barcode reader, a cellular modem, a service stick. A hub controller is the part that makes one port into four or seven, and the number that matters is not the port count but the transaction translator. A single translator hub shares one buffer between all downstream ports, so a full speed device can hold up the high speed traffic on another port; a multiple translator hub gives each port its own, which is why docking stations and instruments use the multiple version.
The SuperSpeed group is for boards that carry USB 3.x. The TUSB8041 is a four port USB 3.0 hub that runs SuperSpeed and USB 2.0 in parallel, with four transaction translators, per port or ganged power switching, overcurrent inputs, battery charging in CDP and DCP mode, and configuration through pin straps, OTP, an I2C EEPROM or an I2C and SMBus interface. The USB5744 does the same job at USB 3.2 Gen 1 with a dedicated USB 2.0 controller, battery charging on the upstream and downstream ports, and OTP or SPI ROM configuration in a 7 mm by 7 mm package.
The USB 2.0 group covers the cost sensitive end. The TUSB4041I is a four port 480 Mbps hub with four transaction translators and a 64 pin HTQFP package rated to minus 40 degrees. The USB2514B and the seven port USB2517 use the Microchip multiple translator architecture with an I2C EEPROM or SMBus configuration port. The CY7C65632 keeps the bill of materials small with a single 5 V supply, an internal regulator and integrated termination resistors, while the GL850G and the GL852G cover the single translator and multiple translator versions of the same four port function.
Key Specifications
| Parameter | SuperSpeed hubs | USB 2.0 hubs |
|---|---|---|
| Upstream speed | 5 Gbps SuperSpeed plus USB 2.0 in parallel | 480 Mbps high speed, 12 Mbps full speed |
| Downstream ports | Four | Two to seven depending on part |
| Transaction translators | One per port on TUSB8041; dedicated USB 2.0 controller on USB5744 | One per port on USB2514B, USB2517 and TUSB4041I; single translator on CY7C65632 and GL850G |
| Port power control | Per port or ganged, with overcurrent inputs | Per port or ganged, with overcurrent inputs |
| Battery charging | CDP and DCP on TUSB8041; DCP, CDP and SDP on USB5744 | CDP and DCP on TUSB4041I |
| Configuration | Pin strap, OTP, I2C EEPROM, I2C and SMBus, or SPI ROM | Pin strap, I2C EEPROM or SMBus |
| Supply | 3.3 V and 1.1 V rails, 5 V VBUS detection | 3.3 V core with an integrated 5 V to 3.3 V regulator on some parts |
| Package | VQFN-64 9 by 9 mm, VQFN-56 7 by 7 mm | QFN-36 6 by 6 mm, QFN-64 9 by 9 mm, HTQFP-64, LQFP-48 |
Included Models and Order Codes
The table lists the order codes most often quoted for docks, instruments, panel PCs and embedded carriers. State the upstream speed, the number of ports, whether full speed devices share the bus and whether the ports have to charge, and the part is confirmed.
| Part Number | Protocol | Downstream Ports | Transaction Translators | Port Power | Package |
|---|---|---|---|---|---|
| TUSB8041IPAPR | USB 3.0, 5 Gbps | 4 | Four, one per port | Per port or ganged with overcurrent | HTQFP-64, 12 by 12 mm |
| USB5744-I/2G | USB 3.2 Gen 1, 5 Gbps | 4 | Dedicated USB 2.0 controller | Per port, ganged or combined | VQFN-56, 7 by 7 mm |
| TUSB4041IPAPR | USB 2.0, 480 Mbps | 4 | Four, one per port | Per port or ganged with overcurrent | HTQFP-64, 12 by 12 mm |
| USB2514B-AEZC | USB 2.0, 480 Mbps | 4 | Multiple, one per port | Per port or ganged | QFN-36, 6 by 6 mm |
| USB2517-JZX | USB 2.0, 480 Mbps | 7 | Multiple, one per port | Per port or ganged | QFN-64, 9 by 9 mm |
| CY7C65632-28LTXCT | USB 2.0, 480 Mbps | 4 | Single translator | Individual or ganged | QFN-28, 5 by 5 mm |
| GL850G-HHY22 | USB 2.0, 480 Mbps | 4, 3 or 2 by pin configuration | Single translator | Individual or ganged | LQFP-48 |
| GL852G-HHY22 | USB 2.0, 480 Mbps | 4 | Multiple, one per port | Individual or ganged | LQFP-48 |
Key Features
One translator per port – a multiple translator hub keeps a 12 Mbps keyboard from holding the 480 Mbps port that carries the instrument data, which is the difference between a usable dock and a complaint.
Power switching on chip – per port enable outputs and overcurrent inputs let the hub turn off only the port that saw a short, instead of dropping every device on the board.
Battery charging modes – CDP and DCP handshaking on the TUSB8041 and the USB5744 lets a port charge a phone at the same time as it enumerates, without an external charging controller.
Configuration without firmware – pin straps, OTP or an I2C EEPROM set the vendor ID, the product ID and the port count, so a hub can be customised on the line with no code in the host.
Small bill of materials – the CY7C65632 runs from a single 5 V supply with an internal regulator and integrated termination resistors, which removes the external LDO and the pull up network.
Industrial temperature parts – the TUSB4041I and the USB2514Bi are rated to minus 40 degrees, which covers a panel PC or a cabinet mounted controller.
Applications
These controllers are quoted for boards that expose more than one USB port, typically where: A hub board is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same assembly, so the controller, the connector and the ESD array arrive as one kit.
Instruments and panel PCs – a single host port has to serve a keyboard, a USB stick for data export and a service modem, and the multiple translator part keeps each one at its own speed.
Docks and display hubs – a dock needs four ports, per port power control and charging on at least one port, which is what the SuperSpeed parts provide with battery charging on the downstream ports.
Embedded carriers and gateways – a carrier board with a module that exposes one USB interface uses a two or four port hub to bring the connector to the front panel and to keep the trace length short.
Sourcing and Cross-Reference
USB hubs are replaced when a board moves from USB 2.0 to USB 3.x, or when the original part becomes hard to find. The replacement has to match the upstream speed, the number of ports, the transaction translator architecture, the power switching scheme and the configuration method, because two parts with the same pin count can differ in whether they need an external EEPROM and in whether the port power pins are active high. We quote those points per line before an order is released.
The parts around the hub decide whether it enumerates at all: the 24 MHz or 25 MHz reference, the VBUS detection divider, the port power switches, the overcurrent sense network and the ESD array on the connector side. We quote the hub, the reference, the power switches and the ESD array as one set for a port group, so the current budget and the fault behaviour are calculated together.
Where the boards are built in volume, SUPERB Assembly support covers the SMT build and the inspection of the fine pitch QFN and HTQFP parts.
Q: Can you supply a hub controller that replaces an existing part without changing the port power circuit?
A: Yes. Send the current part number, the upstream speed, the number of ports and how the port power is switched, and the SUPERB Tech sales team will confirm the order code and the nearest part that keeps the same configuration method.
Why Buyers Source USB Hubs Through SUPERB
- Port architecture on the quote: the translator count, the port count and the power switching scheme are stated per line, so the part matches the traffic the board will carry.
- Hub and passives together: the reference, the port switches and the ESD array for one port group are quoted with the hub, so the current budget is not an estimate.
- Fine pitch assembly: QFN and HTQFP parts are placed and inspected on the same line that supplies them, which keeps first pass yield visible.
- Lifecycle cover: parts that a dock or an instrument was qualified around are held with date codes, so production continues while an alternative is qualified.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Multi-function ICs, USB Type-C and power delivery controllers, Logic level shifters and IO expanders, Digital isolators, Load switches and hot swap controllers, BOM shortage recovery.