Contact Us
  • Home
  • COMPONENTS
  • Supercapacitors and Backup Energy Cells for RTC Hold Up

Supercapacitors and Backup Energy Cells for RTC Hold Up

Electric double layer cells from 0.1 F to 350 F at 2.7 V, 5.5 V and 8.1 V. ESR from 12 mΩ on a 100 F cell, and leakage current from 10 uA on a coin cell. Cycle life is 500,000 cycles on the cylindrical parts, with 1500 hours at 85 C on the radial types. Each row lists case size and temperature range, because those two decide the substitute.
quote now

Product Specifications

Product Overview

A supercapacitor stores charge in an electric double layer instead of in a chemical reaction. That is why it takes a charge in seconds, delivers tens of amps for a short pulse, and keeps working after hundreds of thousands of cycles, which is exactly what an RTC rail, a memory back up rail or a valve pulse needs. It is also why the part loses voltage in a straight line rather than holding a flat plateau the way a battery does.

Three numbers decide whether a cell fits. The first is ESR: a 0.1 F coin cell with 75 Ω of internal resistance cannot feed a pulse, while a 100 F cylindrical cell at 12 mΩ can deliver over a hundred amps for a second. The second is leakage current: it sets how long a charged cell holds a real time clock alive, and it rises with temperature. The third is the voltage limit: a 2.7 V cell is charged to 2.7 V and no more, so a 5 V rail needs two cells in series with a balancing path, and an 8.1 V module is three cells stacked.

The table below lists the cells quoted most often. Cylindrical parts run from 1 F to 350 F at 2.7 V with radial tabs or screw terminals, coin and stacked coin parts cover 0.1 F to 0.47 F at 5.5 V for memory back up, and the 8.1 V range covers 0.33 F to 5 F in a flat pack. Cycle life, shelf life and the temperature at which the rated voltage has to be derated are listed with each family, because a cell run at 85 C holds less of its rating than the same cell at 25 C.

Key Specifications

Parameter2.7 V cylindrical cell5.5 V coin and stacked8.1 V flat module
Rated voltage2.7 V, surge 3.0 V5.5 V, two cells in series8.1 V, three cells in series
Capacitance range1 F to 350 F0.1 F to 1.5 F0.33 F to 5 F
ESR12 mΩ to 200 mΩ30 Ω to 75 Ω at 1 kHzquoted per part at 1 kHz
Leakage current10 uA to 260 uA10 uA to 300 uAquoted per part
Operating temperature-40 C to +65 C, +85 C with derating-25 C to +70 C, -40 C on some series-40 C to +65 C
Cycle life500,000 cycles to half voltage1000 hours at 70 C endurance500,000 cycles
Charge methodconstant voltage, current limitedconstant voltage, current limitedconstant voltage with cell balancing
Typical usepulse power, UPS ride through, valve driveRTC and SRAM back uplonger back up on a 5 V rail

Included Models and Order Codes

The table lists the cells we quote most often. Capacitance, rated voltage, ESR and case size are copied from the maker data sheet for each part number. Where a part is rated for a reduced voltage at the top of its temperature range, the derating point is noted in the Key Features section rather than in a separate column.

Part NumberCapacitanceVoltageESRCaseOperating Range
HV0810-2R7105-R1 F2.7 V0.200 ΩRadial 8 x 10 mm-40 to +65 C
HV0820-2R7305-R3 F2.7 V0.080 ΩRadial 8 x 20 mm-40 to +65 C
HV1030-2R7106-R10 F2.7 V0.034 ΩRadial 10 x 30 mm-40 to +65 C
HV1625-2R7256-R25 F2.7 V0.027 ΩRadial 16 x 25 mm-40 to +65 C
HV1840-2R7606-R60 F2.7 V0.018 ΩRadial 18 x 40 mm-40 to +65 C
HV1860-2R7107-R100 F2.7 V0.012 ΩRadial 18 x 60 mm-40 to +65 C
BCAP0350 E270 T11350 F2.7 V3.2 mΩ DCRadial tab, 60 g-40 to +65 C
DGH106Q2R710 F2.7 V40 mΩ at 1 kHzRadial, PC pins-40 to +85 C
EECS0HD1040.1 F5.5 V75 Ω at 1 kHzCoin 10.5 x 5.5 mm-25 to +70 C
EECS0HD2240.22 F5.5 V75 Ω at 1 kHzCoin 13.5 x 7.5 mm-25 to +70 C
EECF5R5U474N0.47 F5.5 V30 Ω at 1 kHzStacked coin 21.5 x 8 mm-40 to +70 C

Key Features

Charge time measured in seconds – a cell with 12 mΩ of ESR reaches its rated voltage from empty in seconds at a current the charger can supply, so a back up rail is ready again long before the next power cut.

Cycle life far past a battery – 500,000 cycles from rated voltage to half voltage is the figure on the cylindrical families, and the cell does not need a protection circuit to reach it.

Low ESR for pulse duty – a 100 F cell at 12 mΩ delivers 115 W of peak power at 2.7 V, which is why these cells drive solenoids, valves and camera flash instead of a battery pack.

Leakage sets the hold up time – a 0.1 F cell at 75 Ω and 10 uA of leakage holds an RTC for weeks, while the same capacitance with higher leakage drains in days, so leakage is quoted with the part.

Voltage derating at the top of the range – cells rated to +85 C must be held at 2.3 V above +65 C, and the 5.5 V stacked parts drop to 4.6 V at their upper limit, which changes the charger setting.

Series stacking needs balancing – two 2.7 V cells in series make a 5.4 V rail only if the midpoint is held, otherwise one cell passes 3 V and ages first. Balancing resistors or an active balancer are quoted with the stack.

Applications

These cells are quoted for boards that have to keep a rail alive or deliver a short pulse, typically where: The cell sits next to the RTC or the connector on the same board, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Real time clock and SRAM back up – a 0.1 F to 0.47 F 5.5 V cell holds the RTC and the configuration SRAM for weeks after the main supply drops, and it recharges through a resistor on the first power up.

Metering and industrial terminals – a 1 F to 10 F cell on a 2.7 V rail carries the board through a supply dip long enough to write the last readings to flash and shut down in order.

Pulse load on a small supply – a 25 F to 350 F cell supplies the surge of a solenoid, a valve or a camera flash, so the main supply can be sized for the average load instead of the peak.

Sourcing and Cross-Reference

A supercapacitor is chosen on the load profile, not on capacitance alone. The same 10 F of capacitance holds a rail for very different times depending on the current drawn, and a cell with 40 mΩ of ESR drops more voltage at the start of a pulse than a cell with 12 mΩ. The working method is to take the discharge current, the time the load has to be held, and the lowest voltage the load still runs at, then check the ESR drop against the capacitance fall.

The second half of the check is mechanical and thermal. A 350 F cell is 60 g and 60 mm tall, and it needs a holder or a clamped terminal rather than a solder joint on a thin board. A coin cell at 5.5 V has to stay below its derated voltage at the top of the enclosure temperature, and the series stack needs the midpoint held from the first charge.

Where a family has been discontinued, the usual replacement is a cell with the same capacitance and case, equal or lower ESR and a leakage current that does not cut the hold up time. The route for these parts is on our BOM shortage recovery page, and the replacement check for a discontinued cell is on pin to pin cross reference.

For volume builds, SUPERB Assembly support covers the holder or tab soldering, the balancing resistors on a series stack and the charge resistor the cell needs.

Q: Can you supply a 5.5 V back up cell that drops into a footprint built for a discontinued part?

A: Yes. Send the capacitance, the voltage rail, the hold up time, the load current and the footprint, and the SUPERB Tech team will confirm which cell fits and quote it with the ESR and leakage figures for that part.

Why Buyers Source Back Up Cells Through SUPERB

  1. Hold up time checked against the load: the capacitance is sized from the current and the lowest voltage the load accepts, not from the number printed on the old part.
  2. ESR quoted with the cell: the voltage drop at the start of a pulse is calculated from the ESR of the candidate, so a part that fits the footprint but sags below the threshold is not offered.
  3. Temperature derating applied: the charger setting is checked against the derated voltage at the top of the enclosure temperature, which is where most back up rails fail in the field.
  4. Stack and holder quoted together: a series stack is quoted with its balancing path and the cell with its holder, so the assembly does not need a second sourcing step.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Passive components, MLCC and ceramic capacitors, Aluminum electrolytic and tantalum capacitors, BOM shortage recovery.