RF Switches and PIN Diode Switches for Signal Routing
Product Specifications
Product Overview
An RF switch is specified at a frequency, and the frequency is the whole story. A part that shows 0.35 dB at 1 GHz can be 0.5 dB at 2 GHz and unusable at 6 GHz, and an isolation figure quoted at 100 MHz tells nothing about the leakage that matters at 3 GHz. Every number in the table below is tied to the frequency it was measured at, because that is the only form in which a switch can be compared with the relay or the second switch it is replacing.
The absorptive parts are for receivers and test paths, where a port that is switched off has to look like 50 ohms. The PE42540 is a 10 Hz to 8 GHz SP4T with 0.8 dB at 3 GHz and 45 dB of isolation at the same point, 33 dBm of compression and 58 dBm of input intercept, in a 5 by 5 mm LGA, which is the shape used in ATE and in multi band instruments. The HMC547ALP3E goes to 20 GHz with more than 50 dB of isolation below 5 GHz, 1.8 dB at 10 GHz and complementary -5 V and 0 V control, in a 3 by 3 mm QFN.
The reflective parts are for transmit paths and for cost sensitive boards. The HMC194AMS8E covers DC to 3 GHz in an MSOP-8 with 50 dB of isolation below 1 GHz, the HMC241ALP3E is a 0.1 to 4 GHz SP4T with a two to four line decoder and 43 dB at 2 GHz, and the PE4259 puts an SPDT in a 1 by 2 mm SC-70 with 0.35 dB at 1 GHz and 33.5 dBm of compression. Where the switch has to hold off a large RF voltage with low distortion, the PIN diodes take over: the BAR64-02V is 0.13 pF and 2.1 ohms at 10 mA, and the SMP1320 is 0.3 pF maximum with 0.9 ohms maximum, both usable to about 10 GHz.
Key Specifications
| Parameter | Absorptive switches | Reflective switches and PIN diodes |
|---|---|---|
| Frequency range | 10 Hz to 8 GHz, and DC to 20 GHz on the HMC547 | DC to 4 GHz, and up to about 10 GHz with PIN diodes |
| Insertion loss | 0.7 to 1.8 dB at the top of the band | 0.35 dB at 1 GHz on the PE4259 |
| Isolation | 45 dB at 3 GHz, more than 50 dB below 5 GHz | 30 dB at 1 GHz, 43 dB at 2 GHz on the SP4T |
| Configuration | SP4T and SPDT, with on chip termination | SPDT, SP4T and single PIN diode elements |
| Control | CMOS two pin decode, or -5 V and 0 V | Positive 0 to 5 V, or a forward bias current |
| Power handling | 30 dBm at 8 GHz, 33 dBm compression | 28 dBm compression, higher with a diode in shunt |
| Switching time | 5 to 14 microseconds | 1.5 to 20 nanoseconds |
| Package | LGA-32 5 by 5 mm, QFN 3 by 3 mm | MSOP-8, LFCSP-16, SC-70-6, SC-79 |
Included Models and Order Codes
The table lists the order codes most often quoted for instruments, radios and antenna routing. State the band, the isolation needed at the highest frequency, the power the switch has to pass, the control levels available and whether the off port has to be terminated, and the part and its packing are confirmed.
| Part Number | Configuration | Frequency | Isolation | Insertion Loss | Package |
|---|---|---|---|---|---|
| PE4259 | SPDT, reflective | 10 MHz to 3 GHz | 30 dB at 1 GHz, 20 dB at 2 GHz | 0.35 dB at 1 GHz, 0.5 dB at 2 GHz | SC-70-6, 1 by 2 mm |
| PE42540 | SP4T, absorptive | 10 Hz to 8 GHz | 45 dB at 3 GHz, 31 dB at 8 GHz | 0.8 dB at 3 GHz, 1.2 dB at 8 GHz | LGA-32, 5 by 5 mm |
| HMC194AMS8E | SPDT, reflective | DC to 3 GHz | 50 dB below 1 GHz, 30 dB at 3 GHz | 0.9 dB maximum to 2 GHz | MSOP-8 |
| HMC241ALP3E | SP4T, absorptive, decoded | 100 MHz to 4 GHz | 43 dB at 2 GHz, 32 dB at 4 GHz | 0.7 dB at 2 GHz, 1.2 dB at 4 GHz | LFCSP-16, 3 by 3 mm |
| HMC345LP3E | SP4T, absorptive | DC to 8 GHz | 32 dB at 8 GHz | 2.4 dB at 8 GHz | QFN-16, 3 by 3 mm |
| HMC547ALP3E | SPDT, absorptive | DC to 20 GHz | 50 dB below 5 GHz, 36 dB at 20 GHz | 1.8 dB at 10 GHz, 2.5 dB at 20 GHz | QFN-16, 3 by 3 mm |
| BAR64-02V | Single PIN diode | DC to 6 GHz | Set by the circuit, 150 V reverse | 0.13 pF, 2.1 ohms at 10 mA | SC-79 |
| SMP1320-079LF | Single PIN diode | 10 MHz to 10 GHz | Set by the circuit, low capacitance | 0.3 pF maximum at 30 V, 0.9 ohms maximum | SC-79 |
Key Features
Numbers tied to a frequency – isolation and loss are quoted at 1, 2, 3, 8 and 20 GHz where the datasheet gives them, so a part is judged at the band it will actually run in.
Absorptive off ports – an internally terminated port keeps the VSWR of a receive chain constant when a channel is deselected, which a reflective switch cannot do.
Decoded control – a two to four line decoder removes the external logic that an SP4T would otherwise need, which matters when four switches share a small board.
Power handling – 33 dBm of compression and 58 dBm of intercept on the PE42540 is enough to sit before a power amplifier without a limiter.
Fast switching – microsecond switching on the IC parts and nanosecond switching on the PIN diodes covers both TDD radios and pulse modulators.
Small footprint – a 1 by 2 mm SC-70 SPDT and a 3 by 3 mm QFN SP4T keep the switch next to the connector, which is where the loss has to be lowest.
Applications
These switches are quoted for signal routing in radios, instruments and antenna systems, typically where: An RF switch board is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same assembly, so the switch, the launch and the shielding are handled as one build.
Test and measurement – an ATE front end switches four instruments onto one device under test, and an absorptive port keeps the unused inputs terminated at 50 ohms.
Radio front ends – a TDD radio switches the antenna between the power amplifier and the low noise amplifier, where isolation at the transmit frequency sets how much power leaks into the receiver.
Antenna and filter selection – a multi band terminal selects one of several SAW filters or antennas, and a decoded SP4T replaces two SPDT parts and the logic between them.
Sourcing and Cross-Reference
RF switches are frequently replaced by parts that look identical in a pinout table and are not. The control logic polarity, the need for a negative supply, the absorptive or reflective nature of the off port and the frequency at which the isolation was measured all change the board. We quote the configuration, the control levels, the supply and the isolation at the customer band on the confirmation, so a second source is checked against the circuit rather than the footprint.
The board is part of the switch. A 3 by 3 mm QFN needs a ground via under every pad, a 50 ohm trace that is actually 50 ohms at 8 GHz, and a control line that is filtered so the switching transient does not appear in the receive band. We quote the switch with the DC blocking capacitors and the bias network, and where the board is built in volume the launch and the via pattern are reviewed before the first panel.
Where the switch boards are built in volume, SUPERB Assembly support covers the placement of the QFN and LGA parts and the reflow that the 0.4 mm pitch needs.
Q: Can you supply an RF switch that matches an obsolete Hittite or pSemi part?
A: Yes. Send the band, the configuration, the control levels and the isolation needed at the top of the band, and the SUPERB Tech sales team will confirm the order code, the packing and the nearest part with the same control interface.
Why Buyers Source RF Switches Through SUPERB
- Band specific numbers: isolation and insertion loss are quoted at the frequency the customer uses, not at the lowest point of the band where every part looks good.
- Control and supply checked: the logic polarity, the negative rail and the absorptive or reflective off state are confirmed before a replacement is offered.
- Obsolete Hittite and pSemi parts: parts that are no longer recommended are held with date codes, which keeps an instrument or a radio in production while a new layout is qualified.
- Board and switch together: the launch, the via pattern and the bias network are quoted with the part, so the measured isolation is the one on the datasheet.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Frequency converters and sources, RF transceiver ICs, VCO and PLL synthesizers, RF gain blocks and LNAs, RF component sourcing.