Baluns and RF Transformers for Differential Signal Paths
Product Specifications
Product Overview
A balun converts between a single ended line and a differential pair, and an RF transformer does the same job while also changing the impedance. Both are used at the point where a differential amplifier, a mixer, an ADC input or a push pull stage meets a 50 Ω line, and both are specified by the same four numbers: the impedance ratio, the bandwidth over which the part works, the insertion loss in band, and how well the two outputs stay balanced in amplitude and phase.
The bandwidth is given at three levels, and the level matters. A part quoted as 0.4 MHz to 800 MHz with 3 dB bandwidth only holds its loss within 3 dB at the edges, while the same part holds 1 dB from 1 MHz to 400 MHz. Reading only the headline figure is how a transformer ends up on a board where it adds 2.4 dB at the top of the band. Balance behaves the same way: the phase balance of 1 degree applies inside the 1 dB band, and it widens to 4 degrees at the 2 dB edges.
The parts on this page run from a 1:1 transformer covering 80 kHz to 200 MHz for audio band and IF work, through 1:1 and 1:4 parts for HF and VHF radio, up to ceramic balun filters at 2.4 GHz for short range radios. Power handling is modest on purpose, 0.25 W to 2 W, and DC current through the windings is limited to 30 mA on most types, because the ferrite core saturates and the inductance falls away.
Key Specifications
| Parameter | Wire wound transformer | Ceramic balun filter |
|---|---|---|
| Frequency range | 80 kHz to 1.2 GHz by part | 2400 MHz to 2500 MHz |
| Impedance ratio | 1:1 and 1:4 | 50 Ω unbalanced to a conjugate match |
| Insertion loss | 0.3 dB to 1 dB in the 1 dB band | 1.5 dB max from -40 C to +85 C |
| Amplitude balance | 0.1 dB to 0.7 dB | quoted with the filter curve |
| Phase balance | 1 to 5 degrees | 180 degrees plus or minus 15 degrees |
| Return loss | 16 dB to 22 dB | 9.5 dB min |
| Power handling | 0.25 W to 0.5 W | 2 W max |
| DC current in the winding | 30 mA max | not applicable |
Included Models and Order Codes
The table lists the parts we quote most often for receiver front ends, ADC inputs and short range radios. Frequency range, ratio, insertion loss and balance figures are taken from the maker data sheet; where a part is specified with a 1 dB band narrower than its 3 dB band, the 1 dB figure is the one in the table.
| Part Number | Ratio | Frequency | Insertion Loss | Balance | Case |
|---|---|---|---|---|---|
| ADT1-1+ | 1:1, 50 Ω | 0.15 to 400 MHz | 0.3 dB mid band | 0.1 dB, 2 deg | SMD, 7.6 x 6.9 mm |
| ADT1-1WT+ | 1:1, 75 Ω | 0.4 to 800 MHz | 0.3 dB mid band | 0.1 dB, 1 deg | SMD, 7.6 x 6.9 mm |
| ADT1-1WT-1+ | 1:1, 75 Ω | 1 to 400 MHz | 1 dB max | 0.7 dB, 5 deg | SMD, 7.6 x 6.9 mm |
| T1-1T-KK81+ | 1:1, 50 Ω | 0.08 to 200 MHz | quoted per data sheet | quoted per data sheet | SMD, 6 pin |
| ADTL1-12+ | 1:1, 50 Ω | 20 MHz to 1.2 GHz | quoted per data sheet | quoted per data sheet | SMD, 6 pin |
| ADT4-1WT+ | 1:4 | 2 to 775 MHz | quoted per data sheet | quoted per data sheet | SMD, 6 pin |
| 2450BM15A0002 | Balun band pass | 2400 to 2500 MHz | 1.5 dB max | 180 deg, 15 deg | 0805 ceramic |
Key Features
Ratio sets the impedance match – a 1:1 part matches 50 Ω to 50 Ω or 75 Ω to 75 Ω, while a 1:4 part turns 50 Ω into 200 Ω, which is the ratio a push pull pair or a high impedance mixer port needs.
Bandwidth quoted at a loss level – the 1 dB band is the working band. The 3 dB figure on the same data sheet is wider, and using it as the working band costs 2 dB at each end.
Balance held inside the band – 0.1 dB of amplitude balance and 1 degree of phase balance inside the 1 dB band, widening to 0.5 dB and 4 degrees at the 2 dB edges, which matters for a differential ADC input.
Low insertion loss – 0.3 dB typical mid band loss keeps the transformer out of the noise figure budget, and the loss curve rises toward the band edges where the core coupling falls.
Small power and DC limits – 0.25 W to 0.5 W of RF power and 30 mA of DC in the winding, which rules these parts out of a transmit chain but fits a receive path or a local oscillator feed.
Ceramic balun with a filter – the 2.4 GHz part carries the balun and a band pass filter in one 0805 body, with 18 dB of attenuation at 4.8 GHz to 5 GHz and 20 dB at 7.2 GHz to 7.5 GHz.
Applications
These parts are quoted at the point where a differential circuit meets a single ended line, typically where: The balun sits between the filter and the differential stage on the same board, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.
Receiver front end into a differential amplifier – a 1:1 transformer converts the single ended signal from the filter into a balanced pair for a differential amplifier, which removes the common mode noise picked up on the line.
ADC input on an instrument board – a 1:4 transformer steps a 50 Ω source up to the 200 Ω input of a high speed converter, and the amplitude balance keeps the even harmonics from rising.
2.4 GHz short range radio – a 0805 ceramic balun filter matches the differential RF port of the radio chip to the antenna and suppresses the second and third harmonic in one part.
Sourcing and Cross-Reference
A balun is chosen on the band it has to cover and the ratio the two sides need, then checked on balance and on loss. Two parts with the same ratio and the same headline bandwidth can differ by 0.5 dB of loss in the middle of the band and by 3 degrees of phase balance, and that difference shows up as a rise in the even order distortion of the stage behind it.
The mechanical side is usually the reason a part is replaced. Case styles differ between makers even at the same ratio, the pin out of a 6 pin transformer is not standard between families, and a part with a centre tap on the secondary needs the tap pad on the board. Where the original is no longer available, the replacement is checked on ratio, band, loss, balance and pin out before a sample is offered.
The route for these parts is on our RF component sourcing page, and the replacement path for a part that has been dropped by its maker is on obsolete RF part replacement.
For volume builds, SUPERB Assembly support covers the placement of the 6 pin transformer, the ground vias beside it and the reflow profile the ceramic body needs.
Q: Can you supply a balun with the same ratio and pin out as a part that the original maker has discontinued?
A: Yes. Send the ratio, the band, the loss and balance limits, the pin out and the case size, and the SUPERB Tech team will confirm which part matches and quote it with measured balance for the band.
Why Buyers Source Baluns and RF Transformers Through SUPERB
- Band quoted at the working loss: candidates are compared on the 1 dB band rather than the 3 dB headline, so the part still works at the band edges of the application.
- Balance checked on the data sheet: amplitude and phase balance are compared inside the working band, which is where a differential stage is most sensitive to them.
- Pin out confirmed before quoting: the pin arrangement and the centre tap are checked against the land pattern, because a matching ratio in a different pin out is not a drop in part.
- Loss kept inside the chain budget: a 0.3 dB part is not offered where the noise figure was calculated on 0.3 dB and the alternative measures 0.8 dB in band.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Frequency converters and sources, RF isolators and circulators, RF power dividers and directional couplers, RF component sourcing.