Film Capacitors for Snubber and AC Filter Applications
Product Specifications
Product Overview
A film capacitor is a metalized plastic film wound or stacked into a box. It does not dry out the way an electrolytic does, it self heals after a local breakdown, and it holds its capacitance over temperature and voltage far better than a ceramic. That combination is why it sits in snubbers, across AC mains, in pulse circuits and in filters where a stable value matters more than capacitance per cubic millimetre.
Two families cover most of the work. A metalized polyester part in a 5 mm lead spacing box, 0.1 uF to 1 uF at 63 V to 100 V, is used for coupling, timing, filtering and low voltage snubbers. An X2 class suppression capacitor at 305 V AC in a 15 mm or 27.5 mm spacing is used across the mains, where the part has to survive the surge test and fail open rather than short. The X2 part carries the safety approval, and that approval is what makes it usable across the line.
The figure that limits both is dv/dt. A snubber sees a fast voltage edge every switching cycle, and the film carries a rated dv/dt in volts per microsecond that must not be exceeded. A 0.1 uF X2 part in a 15 mm case is rated at 340 V/us, the same value in a 27.5 mm case at 120 V/us, and a polyester part in a 5 mm case has its own limit. A part that fits the footprint but has a lower dv/dt rating will lose capacitance at the edges and fail early.
Key Specifications
| Parameter | Metallized polyester, 5 mm | X2 suppression, 15 mm | X2 suppression, 27.5 mm |
|---|---|---|---|
| Capacitance range | 0.1 uF to 1 uF | 0.1 uF to 0.22 uF | 0.68 uF to 1 uF |
| Voltage rating | 63 V DC, 100 V DC | 305 V AC | 305 V AC |
| Lead spacing | 5 mm | 15 mm | 27.5 mm |
| dv/dt rating | quoted per part number | 340 V/us | 120 V/us |
| Case size | 7.2 x 2.5 x 6.5 mm and up | 5.0 x 10.5 x 18 mm and up | 11 x 19 x 31.5 mm |
| Temperature range | -55 C to +105 C | -40 C to +110 C | -40 C to +110 C |
| Safety class | none | X2, EN 60384-14 | X2, EN 60384-14 |
| Typical use | coupling, timing, low voltage snubber | across the mains, EMI filter | across the mains, larger values |
Included Models and Order Codes
The table lists the parts we quote most often. Capacitance, voltage, lead spacing, case dimensions and dv/dt are copied from the maker data sheet for each part number. The polyester parts are AEC-Q200 qualified where the part number carries the suffix, and the X2 parts carry the EN 60384-14 approval.
| Part Number | Type | Capacitance | Voltage | Lead Spacing | Case |
|---|---|---|---|---|---|
| R82DC3100DQ50J | Polyester, stacked | 0.1 uF | 63 V DC | 5 mm | 7.2 x 2.5 x 6.5 mm |
| R82DC3330AA60J | Polyester, stacked | 0.33 uF | 63 V DC | 5 mm | 7.2 x 3.5 x 7.5 mm |
| R82DC4100AA60J | Polyester, stacked | 1 uF | 63 V DC | 5 mm | 7.2 x 5 x 10 mm |
| R82EC3100DQ70J | Polyester, stacked | 0.1 uF | 100 V DC | 5 mm | 7.2 x 2.5 x 6.5 mm |
| B32922C3104K000 | X2, polypropylene | 0.1 uF | 305 V AC | 15 mm | 5.0 x 10.5 x 18 mm |
| B32922C3154K000 | X2, polypropylene | 0.15 uF | 305 V AC | 15 mm | 6.0 x 12 x 18 mm |
| B32922C3224K000 | X2, polypropylene | 0.22 uF | 305 V AC | 15 mm | 7.0 x 12.5 x 18 mm |
| B32924C3684K000 | X2, polypropylene | 0.68 uF | 305 V AC | 27.5 mm | 11 x 19 x 31.5 mm |
Key Features
dv/dt is the pulse limit – 340 V/us on a 15 mm X2 part against 120 V/us on a 27.5 mm part of the same class, so a larger case does not mean a faster part.
Self healing after a breakdown – a metalized film clears a local breakdown by evaporating the metallization around it, which is why the part fails open instead of shorting across the mains.
Stable value over temperature – the capacitance of a polyester or polypropylene film moves by a small amount across the range, where a Class II ceramic loses a large share of its value under DC bias.
X2 approval for line side use – the 305 V AC parts carry EN 60384-14 as X2, which is the approval a line to line position needs and which a general purpose film part does not have.
Lead spacing that fits the board – 5 mm, 15 mm and 27.5 mm versions cover a small coupling part and a line filter part with the same family, so the footprint can be kept from the previous build.
Temperature to 105 C and 110 C – the polyester parts are rated to +105 C and the X2 parts to +110 C, which covers a board inside an enclosure without derating the voltage.
Applications
These capacitors are quoted where a circuit needs a stable value or a line needs a safety approved part, typically where: The film part sits at the input connector or across the switching device on the same board, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.
Snubber across a switching device – a 0.1 uF to 1 uF polyester part in a 5 mm case absorbs the turn off spike across a MOSFET or a diode, with the dv/dt rating set against the switching edge.
Across the mains in an EMI filter – a 0.1 uF to 0.68 uF X2 part shunts the differential mode noise between line and neutral, and the 305 V AC rating with EN 60384-14 covers the surge test.
Coupling and timing in an analog stage – a 0.1 uF polyester part couples a signal between stages with a value that does not drift with voltage, which a Class II ceramic cannot promise.
Sourcing and Cross-Reference
The starting point is the position on the board. A part across the mains needs the X2 approval and the 305 V AC rating before any other number is looked at, because a general purpose film part in that position fails the safety review no matter how good its electrical figures are. A snubber needs the dv/dt rating and the pulse current, and a coupling position needs the value stability and the leakage.
The second check is mechanical. A 27.5 mm lead spacing part is 31.5 mm long and will not fit where a 15 mm part was, and a box that is 19 mm tall can foul a heat sink. The lead spacing, the case dimensions and the dv/dt are quoted together, because a part with the right capacitance and the wrong spacing is a board change rather than a replacement.
Where a series has been discontinued, the replacement is matched on capacitance, voltage and class first, then on lead spacing, case size and dv/dt. The route for these parts is on our pin to pin cross reference page, and the cost question for a board with several film parts is on how to reduce component cost.
For volume builds, SUPERB Assembly support covers the lead forming, the spacing check against the pad and the potting or coating step the film body allows.
Q: Can you supply an X2 capacitor with the same lead spacing and a higher dv/dt rating than the part we use now?
A: Yes. Send the capacitance, the voltage and the class, the lead spacing, the case limit and the dv/dt the position sees, and the SUPERB Tech team will confirm which part fits and quote it with the approval it carries.
Why Buyers Source Film Capacitors Through SUPERB
- Safety class checked first: a line side position is matched with an X2 part at 305 V AC, so the approval is in place before the price is discussed.
- dv/dt matched to the edge: the switching edge is compared with the dv/dt rating of the candidate, which is where a snubber part fails when it is chosen on capacitance alone.
- Lead spacing and height confirmed: 5 mm, 15 mm and 27.5 mm spacing with the case height are checked against the board, so the part does not turn into a layout change.
- Value stability quoted: polyester and polypropylene parts are offered where the capacitance has to hold over voltage and temperature, which is the reason the film part was there.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Passive components, MLCC and ceramic capacitors, Aluminum electrolytic and tantalum capacitors, Pin to pin cross reference.