Contact Us
  • Home
  • COMPONENTS
  • IGBTs and SiC Power Devices for Motor Drives and Inverters

IGBTs and SiC Power Devices for Motor Drives and Inverters

IGBT and SiC MOSFET discretes covering 600 V to 1200 V in TO-247, TO-247-4 and TO-3P packages. On-state values are taken from the maker data sheet at the quoted current and temperature. Co-packed IGBTs, SiC MOSFETs and SiC Schottky diodes are quoted together for one phase leg. Parts under an end of life notice are flagged with the nearest equivalent that keeps the footprint.
quote now

Product Specifications

Product Overview

A motor drive or an inverter stage comes down to two decisions: the voltage class and the switch technology. Below 600 V a trench IGBT with a co-packed diode is still the least expensive way to switch a few kilowatts, and the diode keeps the freewheel path on the same heat sink as the switch. Above 900 V a SiC MOSFET removes most of the tail current that costs an IGBT its efficiency as the switching frequency rises, so the heat sink and the output filter can both be smaller. The parts on this page cover both paths in the same package families, so a board can move from one to the other without a new land pattern.

The gate drive decides how much of the silicon performance is reached. An IGBT wants 15 V on the gate and either 0 V or a small negative rail to turn off cleanly. A SiC MOSFET wants a stiff driver with a separate source return, because the same dv/dt that cuts switching loss also couples into the gate loop through the common source inductance. That is why the IKW40N120CH7 carries a Kelvin emitter pin and the C3M0075120K brings the driver source out on a fourth pin. Both parts cost a little more per piece and save the turn-off loss that a two pin package would add back.

Thermal margin is the third number, and it is usually the one that decides between two parts of the same class. A 1200 V IGBT in TO-247 holds 175 °C junction temperature on the H3 and CH7 families, while the older NPT part on this page stops at 150 °C. A SiC MOSFET at 45 mΩ carries 52 A at 25 °C case but only 36 A at 100 °C case, so the current quoted on a quotation line has to say which case temperature it belongs to. Every row below states the condition, and the switching energy is given at the current the curve was measured at.

Key Specifications

ParameterIGBT discreteSiC MOSFETSiC Schottky diode
Blocking voltage600 V to 1200 V900 V to 1200 V650 V to 1200 V
Current at 25 °C case50 A, falling to 25 A to 40 A at 100 °C case32 A to 52 A, falling to 23 A to 36 A at 100 °C case10 A to 34 A per leg
On-state at 25 °CVCEsat 1.7 V to 2.05 V typicalRDS(on) 45 mΩ to 80 mΩ at 15 V or 20 V gateVF 1.5 V typical at 10 A
Gate drive15 V on, 0 V or -5 V off15 V on, -4 V off on C3M parts; 20 V on for C2M partsnot applicable
Reverse pathco-packed fast diode, Qrr 1200 nC on IKW25N120H3body diode rated for commutationmajority carrier, no reverse recovery charge
Maximum junction temperature150 °C on the NPT part, 175 °C on H3 and CH7150 °C on C2M, 175 °C on C3M and CoolSiC175 °C
Usual switching range8 kHz to 40 kHz hard switched40 kHz to 200 kHzfollows the switch
Package familyTO-247-3, TO-247-4, TO-3PTO-247-3, TO-247-4TO-247-3, TO-220-2

Included Models and Order Codes

The rows below are the order codes quoted most often for drives, inverters and power factor stages. Give the DC bus, the continuous current, the case temperature you can hold and the switching frequency, and the part, the gate resistor range and the packing are confirmed against the data sheet.

Part NumberDevice TypeVoltage ClassCurrent RatingKey On-State and Switching DataPackage
IKW25N120H3IGBT with antiparallel diode1200 V50 A at 25 °C, 25 A at 100 °CVCEsat 2.05 V typical at 25 A, Eoff 0.85 mJTO-247-3
IKW40N120H3IGBT with antiparallel diode1200 V80 A at 25 °C, 40 A at 100 °CVCEsat 2.05 V typical at 40 A, Eoff 1.2 mJTO-247-3
IKW40N120CH7IGBT with Rapid diode and Kelvin pin1200 V40 A at 100 °CVCEsat 1.7 V typical at 25 °C, 10 µs short circuitTO-247-3
IKW50N60H3IGBT with antiparallel diode600 V50 A at 100 °CVCEsat 1.85 V typical, Eoff 0.91 mJTO-247-3
FGA25N120ANTDNPT trench IGBT for soft switching1200 V50 A at 25 °C, 25 A at 100 °CVCEsat 2.0 V typical, Eoff 0.96 mJTO-3P
C3M0065090DSiC MOSFET, N channel900 V36 A at 25 °C, 23 A at 100 °CRDS(on) 65 mΩ at 15 V gate, 90 mΩ at 150 °CTO-247-3
C3M0075120KSiC MOSFET with separate driver source1200 V32 A at 25 °C, 23 A at 100 °CRDS(on) 75 mΩ at 15 V gate, 8 mm drain to source creepageTO-247-4
C2M0080120DSiC MOSFET, second generation1200 V36 A at 25 °C, 24 A at 100 °CRDS(on) 80 mΩ at 20 V gate, listed obsolete by the makerTO-247-3
IMW120R045M1SiC MOSFET, CoolSiC trench1200 V52 A at 25 °C, 36 A at 100 °CRDS(on) 45 mΩ at 15 V gate, 3 µs short circuitTO-247-3
C4D20120DSiC Schottky diode1200 V20 A at 157 °C caseVF 1.5 V typical at 10 A, 52 nC capacitive chargeTO-247-3
IDH10G65C5SiC Schottky diode, thinQ generation 5650 V10 A at 140 °C caseQC 15 nC at 400 V, no forward or reverse recoveryTO-220-2

Key Features

A phase leg on one line – a switch and its SiC Schottky diode are quoted together with the gate resistor range and the driver rail, so the drive stage arrives as one matched set instead of two unrelated part numbers.

Voltage class stated at the terminal – 600 V, 650 V, 900 V and 1200 V parts are listed as separate rows, because a 650 V rectifier behind a 600 V IGBT leaves no margin for the turn-off overshoot on a 400 V bus.

Kelvin and four pin options – the IKW40N120CH7 and the C3M0075120K bring the emitter or source out on a dedicated pin, which removes the common source inductance that slows a hard switched turn-off.

Switching data from the curve – Eoff, Qrr and RDS(on) are copied at the current and temperature the maker measured them at, so a 175 °C value is never compared with a 25 °C value across two rows.

Obsolete power parts tracked – the C2M0080120D carries an end of life notice; a board still using it is matched to the C3M0075120K after the gate voltage, the creepage distance and the driver source are checked.

Parallel bank data – the positive VCEsat coefficient on the H3 and CH7 parts and the absence of thermal runaway on the SiC diodes are the two properties a parallel bank depends on.

Short circuit and avalanche figures – 10 µs short circuit withstand on the 1200 V IGBTs and avalanche energy on the SiC MOSFETs are quoted where the maker publishes them, and left out where it does not.

Thermal path measured at the case – every current rating says whether it belongs to a 25 °C or a 100 °C case, which is the difference between a 52 A and a 36 A quotation for the same part.

Applications

These parts are quoted for power stages that switch a DC bus into a motor winding or a grid tie, typically where: The switch and the driver are placed on the same board, so they are quoted with the SUPERB PCB and the SUPERB PCBA build for that drive card.

Pump and compressor drives – a 400 V bus with 3 kW to 15 kW per phase runs at 8 kHz to 16 kHz, and an IGBT with a co-packed diode keeps the bill of materials low while the heat sink stays inside the enclosure.

Solar and storage inverters – an 800 V to 1000 V bus needs 1200 V switches, and a SiC MOSFET at 45 mΩ allows a 40 kHz to 100 kHz switching frequency that shrinks the boost inductor and the filter.

Power factor correction and welding – hard switched PFC at 65 kHz and welding converters at higher current both depend on the diode reverse recovery, so a SiC Schottky with no Qrr replaces a fast silicon diode pair.

Uninterruptible supplies and chargers – a three level stage on a 1200 V IGBT pair gives a lower harmonic content than a two level stage at the same switching frequency, and the co-packed diode keeps the neutral clamp compact.

Sourcing and Cross-Reference

A power switch is rarely replaced on its own. The gate resistor, the driver supply, the dead time in the firmware and the heat sink interface all belong to the part that was qualified, so a cross reference has to hold the voltage class, the package, the gate voltage and the switching energy at the same time. An IGBT with a lower VCEsat but a larger Eoff can make a drive run hotter at 16 kHz even though the conduction loss looks better on paper.

Status is the other half of the question. The C2M0080120D is listed as obsolete by its maker, and boards still using it are moved to the C3M0075120K or to a 1200 V part at 80 mΩ in TO-247-3 after the gate drive is re-checked, because a 20 V gate part does not accept a 15 V driver without a change at the driver stage. SiC diodes are easier: a 1200 V 20 A rectifier in TO-247-3 swaps across makers as long as the forward voltage at the operating current and the thermal resistance are compared.

Lead time on power discretes moves with the fab, not with the catalogue. A part that shows stock today can be on allocation next quarter, so the quotation line states the batch date and the quantity behind it rather than a generic availability note.

For volume builds, SUPERB Assembly support covers the TO-247 mounting torque, the thermal interface check and the solder profile on the heavy copper pads these parts need.

Q: Can you supply a pin to pin replacement when a 1200 V IGBT or SiC part is discontinued?

A: Yes. Send the current part number, the DC bus, the gate drive voltage and the switching frequency, and the SUPERB Tech sales team will confirm the order code and the nearest part that keeps the same footprint and thermal path.

Why Buyers Source IGBT and SiC Parts Through SUPERB

  1. Voltage class and package matched: the cross reference starts from the bus voltage and the land pattern, so a substitute never arrives with a different creepage distance or a fourth pin that the board does not have.
  2. Switching energy quoted with the part: Eoff and Qrr are given at the current the maker measured them at, which is what decides whether a drive stays inside its heat sink budget.
  3. End of life cover: obsolete power parts are flagged on the quotation with the equivalent that keeps the footprint, before a production line runs out.
  4. One supplier for switch and rectifier: the IGBT, the SiC MOSFET and the SiC Schottky diode for one phase leg come from one line, so the thermal interface and the mounting height stay consistent.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Discrete and power semiconductors, TVS and ESD protection diodes, LED indicators and optocouplers, Power management ICs, Pin to pin cross reference.