Contact Us
  • Home
  • COMPONENTS
  • PCIe Clock Generators and Redrivers for High Speed Links

PCIe Clock Generators and Redrivers for High Speed Links

Clock generators, fanout buffers and redrivers for PCI Express links from Gen 1 to Gen 5. Two to eight low power HCSL outputs with integrated 100 ohm terminations. Additive phase jitter from 40 fs to 156 fs depending on the buffer and the standard. Eight channel redrivers add 36 dB of receiver equalisation for long backplanes.
quote now

Product Specifications

Product Overview

A PCI Express link fails for two reasons that look alike on a scope: the clock arrives with too much jitter, or the data eye closes before it reaches the receiver. The first is a clock distribution problem and is solved with a generator and a fanout buffer. The second is a channel loss problem and is solved with a redriver or a retimer. The parts on this page cover the first two stages and the last one, in packages from 16 pins to 54 pins.

The clock side starts at a 25 MHz crystal. The 9FGV0241 generates two 100 MHz low power HCSL pairs with 100 ohm terminations inside the package, holds cycle to cycle jitter under 50 ps and meets the Gen 1 to Gen 4 phase jitter mask, in a 4 mm by 4 mm package that needs no external termination resistors. The Si52112-B3 does the same job for Gen 3 with two outputs, and the 9DBV0441 and the 9ZXL0831 are the fanout stage: four and eight low power HCSL pairs, a zero delay path, and additive jitter of 156 fs root mean square over 12 kHz to 20 MHz, which drops to 40 fs against the Gen 5 common clock mask.

Where the clock has to reach several cards at different lengths, the LMK00304 provides a 3 to 1 input multiplexer, four differential outputs that can each be LVPECL, LVDS or HCSL, and an additive jitter of 51 fs over 12 kHz to 20 MHz with a 156.25 MHz source. On the data side the DS80PCI800 is an eight channel redriver that equalises up to 36 dB of channel loss and adds up to 12 dB of de-emphasis, holding 0.2 UI of residual deterministic jitter at 8 Gbps after 40 inches of FR-4 or 10 metres of cable, at 65 mW per channel.

Key Specifications

ParameterClock generation and fanoutChannel redriver
StandardPCIe Gen 1 to Gen 4 on 9FGV0241, Gen 1 to Gen 5 on 9DBV0441 and 9ZXL0831PCIe Gen 1, Gen 2 and Gen 3 at 2.5, 5.0 and 8.0 Gbps
OutputsTwo to eight low power HCSL pairs plus one LVCMOS referenceEight channels, usable as four lanes in both directions
Output impedance100 ohm differential, terminated inside the package100 ohm differential, 50 ohm to ground at the receiver
JitterCycle to cycle under 50 ps; additive 156 fs root mean square over 12 kHz to 20 MHz; 40 fs against the Gen 5 mask0.2 UI residual deterministic jitter at 8 Gbps after 40 inches of FR-4
EqualisationPLL bandwidth selectable or bypassedReceiver equalisation up to 36 dB, transmit de-emphasis up to 12 dB
Input25 MHz crystal or clock, 10 MHz to 40 MHz on the LMK00304AC coupled differential from the root complex or the endpoint
Supply voltage1.8 V core on the low power family, 3.3 V on the LMK003042.5 V or 3.3 V, selectable
PowerLow power HCSL push pull outputs, no external resistors65 mW per channel, unused channels can be turned off
Package16 pin to 48 pin VFQFPN, 32 pin WQFN 5 mm by 5 mm54 pin WQFN 10 mm by 5.5 mm

Included Models and Order Codes

The codes below are the ones quoted for server cards, risers, storage backplanes and instrument hosts. State the lane count, the generation, the reference clock, the trace length and whether the link needs a redriver or a full retimer, and the part and the package are confirmed.

Part NumberFunctionOutputsStandardPackage
9FGV0241 (24 pin VFQFPN)Clock generator2 HCSL pairs plus 1 LVCMOSPCIe Gen 1 to Gen 44 mm by 4 mm VFQFPN
Si52112-B3-GTRClock generator2 HCSL outputsPCIe Gen 316 pin TSSOP
9DBV0441 (32 pin VFQFPN)Zero delay fanout buffer4 HCSL pairsPCIe Gen 1 to Gen 55 mm by 5 mm VFQFPN
9ZXL0831 (48 pin VFQFPN)Fanout buffer8 HCSL pairsPCIe Gen 1 to Gen 348 pin VFQFPN
LMK00304SQ/NOPBBuffer and level translator4 differential plus 1 LVCMOSPCIe Gen 3 and general high speed32 pin WQFN 5 mm by 5 mm
DS80PCI800SQ/NOPB8 channel redriver8 channels, x8 or x16 lanePCIe Gen 1 to Gen 3, 8 Gbps54 pin WQFN 10 mm by 5.5 mm

Key Features

Terminations inside the package – the low power HCSL outputs are specified at 100 ohm differential, so the eight 33 ohm resistors and the space they take disappear from the card.

Jitter budget with numbers – 156 fs root mean square over 12 kHz to 20 MHz and 40 fs against the Gen 5 mask are quoted per buffer, so the budget for a two stage fanout can be added up rather than guessed.

Zero delay path – the 9DBV0441 and the 9ZXL0831 lock the output phase to the input, which keeps the skew between cards on a backplane inside the 50 ps the specification allows.

Spread spectrum support – the generator passes spread spectrum through from the reference, so the clock can stay modulated for EMC without a separate path for the PCIe link.

Equalisation that recovers a closed eye – 36 dB of receiver equalisation and 12 dB of de-emphasis let a redriver carry a Gen 3 link across 40 inches of FR-4 that would otherwise fail at the receiver.

Channels that can be switched off – unused lanes are disabled by pin or register, so a x4 riser built on an eight channel part draws only for the lanes it uses.

Applications

These parts are quoted for boards that distribute a reference clock or extend a high speed link, typically where: Clock and link parts are quoted with the SUPERB PCB and the SUPERB PCBA build for the same card, so the reference crystal, the termination and the trace length are checked together.

Server cards and risers – a riser needs two clean 100 MHz pairs with no external resistors and a 25 MHz crystal, which is the 9FGV0241 case, while the host side distributes through an eight output buffer.

Storage and network backplanes – a mid plane carries several cards at different trace lengths, so a zero delay buffer holds the skew and a redriver rebuilds the eye at the far end.

Instrument and test hosts – a host with a 156.25 MHz reference and several converters needs a buffer with selectable output levels, which is why the LMK00304 with LVPECL, LVDS and HCSL outputs is used at that point.

Sourcing and Cross-Reference

Clock parts are replaced more often for availability than for performance, and the trap is that two buffers with the same pin count can differ in the input frequency, the PLL bandwidth, the spread spectrum handling and whether the outputs are terminated inside the package. A part that moves the termination outside needs a board change, and a part with a different PLL bandwidth changes the jitter that reaches the link. We quote the standard, the output count, the input frequency, the jitter figure and the package on every line.

Redrivers add a second dimension because a redriver is not a retimer. A redriver equalises and re-drives the analog waveform, while a retimer recovers the clock and the data and rebuilds the link. Where a link fails because of a protocol or a training issue rather than loss, a redriver will not fix it, so the fault is checked before a part is quoted. Where the loss is the problem, the equalisation range and the VOD setting are quoted against the measured channel loss.

For cards that carry a 0.5 mm pitch VFQFN and a 54 pin WQFN, SUPERB Assembly support covers the reflow profile and the inspection of the exposed pad joints.

Q: Can you supply a PCIe clock buffer that keeps the same jitter and output count as the one we qualified?

A: Yes. Send the standard, the lane count, the reference frequency and the measured channel loss, and the SUPERB Tech sales team will confirm the order code and the nearest part with the same jitter class.

Why Buyers Source PCIe Clock and Link Parts Through SUPERB

  1. Jitter stated, not implied: the additive jitter and the standard it is measured against are quoted per line, so the link budget is built on the part that will be fitted.
  2. Termination and reference checked: whether the outputs are terminated inside the package and which crystal the part expects are confirmed before the order.
  3. Redriver and retimer kept apart: the fault is checked first, so a loss problem is not answered with a part that cannot fix a training failure.
  4. Small pitch assembly support: 0.5 mm pitch packages with an exposed pad are placed and inspected on the same line that supplies them.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Crystals and oscillators, Crystal units and TCXO oscillators, Real time clocks and timing buffers, Clock generators for line cards, Pin to pin cross reference.