Contact Us
  • Home
  • COMPONENTS
  • Laser Diodes and VCSEL Emitters for Optical Modules

Laser Diodes and VCSEL Emitters for Optical Modules

Pulsed 905 nm laser diodes from 70 W to 120 W peak, driven at 30 A to 40 A in a TO-56 can or as a bare die. 850 nm VCSELs at 0.5 mW to 2 mW, and 850 nm datacom VCSELs rated to 10.3125 Gbps, all in TO-46. One 447 nm blue emitter at 3.5 W continuous in a TO-90 can, with 2.2 A of forward current. Every row lists the wavelength band, the drive current and the package, because the package sets the heat path.
quote now

Product Specifications

Product Overview

An emitter is the one part of an optical link whose behaviour cannot be fixed by the circuit around it. A 905 nm pulsed laser diode is driven with 30 A to 40 A for 1 ns to 100 ns and turns that into 75 W to 120 W of peak optical power, which is the source for a range finder or a LiDAR channel. An 850 nm VCSEL runs at 6 mA, emits 0.5 mW to 2 mW out of a small aperture and modulates at 10 Gbps, which is the source inside a short reach optical module. Both are diodes, and almost nothing else about them is the same.

The difference shows up in three numbers. Threshold current is 0.75 A for the pulsed edge emitter and 1 mA to 3 mA for the VCSEL, so the drive circuit is a high current pulse switch on one side and a bias tee on the other. Beam divergence is 9 by 25 degrees from the edge emitter and 8 to 18 degrees circular from the VCSEL, so the optics are a fast collimator on one side and a simple ball lens on the other. Thermal resistance is 160 K/W for the plastic TO-56 and around 8 K/W for a TO-90 metal can, which sets how much the wavelength walks as the part heats.

Wavelength then decides the detector and the fibre. 850 nm couples into multimode fibre and reaches 300 m at 10 Gbps, 905 nm is invisible and chosen for its pulsed power, and 447 nm is visible blue for projection and curing. A 1310 nm or 1550 nm link uses a DFB edge emitter or a TOSA, which is a different supply route and is quoted against the module platform rather than against a generic catalogue number.

The parts on this page are the two emitter families we quote most often: pulsed 905 nm laser diodes in a plastic TO-56 radial can, as a bare die, and as a hybrid with the driver inside the can, plus an 850 nm VCSEL range in TO-46 with and without a monitor photodiode. One 447 nm blue part is listed because it is asked for on the same BOM as the 905 nm parts, and it is now flagged as discontinued by the maker, which is exactly the case our sourcing route exists for.

Key Specifications

ParameterPulsed 905 nm edge emitter447 nm blue edge emitter850 nm VCSEL
Wavelength905 nm, 895 nm to 915 nm band447 nm typical, 440 nm to 455 nm850 nm, 840 nm to 860 nm
Optical power70 W to 120 W peak3.5 W continuous0.5 mW to 2 mW continuous
Drive current30 A to 40 A pulsed2.2 A continuous6 mA continuous
Pulse width1 ns to 100 ns, duty cycle 0.1 %continuous or pulsedcontinuous, modulated to 10.3125 Gbps
Threshold current0.5 A to 1 A0.29 A0.8 mA to 3 mA
Beam divergence9 by 25 degrees FWHM9 by 49 degrees at 1/e28 to 18 degrees circular
PackageTO-56 plastic radial, or bare dieTO-90 metal canTO-46 metal can, flat window
Operating temperature-40 C to 85 C, die to 105 C-40 C to 120 C-40 C to 85 C on the datacom type

Included Models and Order Codes

The table lists the order codes we quote most often, with the figures copied from the maker data sheet for that code. Peak power is at the pulse condition stated by the maker and is not a continuous rating, so the pulse width and duty cycle travel with the number. Where a maker sells the same die as a packaged part and as a bare chip, both are listed because the assembly route differs.

Part NumberFamilyWavelengthOutput PowerDrive CurrentPackageOperating Range
SPL PL90_3 (Q62702P5353)Pulsed laser diode905 nm75 W peak30 A, 100 nsTO-56 plastic radial-40 to +85 C
SPL DS90A_3 (Q65112A3764)Pulsed laser diode905 nm120 W peak40 A pulsedBare die 600 x 400 x 115 um-40 to +105 C
SPL LL90_3 (Q65110A1009)Pulsed laser diode905 nm70 W peakdriver inside the canTO-56 hybrid-40 to +85 C
PLPT9 450LB_E A01 (Q65113A5226)Blue laser diode447 nm3.5 W continuous2.2 ATO-90 metal can-40 to +120 C
VCT-F85A31-SLVCSEL, single mode850 nm0.5 mW6 mATO-46, common cathode-10 to +70 C
VCT-F85A32-SLVCSEL, single mode850 nm0.5 mW6 mATO-46, common anode-10 to +70 C
VCT-F85A32-SPLVCSEL, polarization locked850 nm2 mW6 mATO-46, with monitor PD-20 to +65 C
VCT-F85A42-3VCSEL, 2.5 Gbps850 nm0.5 mW at 6 mA6 mATO-46, common anode-10 to +85 C
VCT-F85A54-10MVCSEL, 10.3125 Gbps850 nm0.9 mW at 6 mA6 mATO-46, isolated monitor PD-40 to +85 C

Key Features

Peak power comes with a pulse condition – 75 W or 120 W is quoted at 30 A to 40 A with a 100 ns pulse and a 0.1 % duty cycle, and the same part run at a longer pulse delivers less, so the drive circuit and the number are read together.

Three emitters in one die stack – the SPL PL90_3 stacks three epitaxial emitters so 9 V of forward voltage produces 75 W of peak power at 30 A, which keeps the current lower than a single junction part of the same power would need.

Monitor photodiode inside the can – the VCSEL parts carry a monitor PD behind the rear mirror, so a module can close an optical power loop without an external tap, and the monitor current at 500 uW to 900 uW of output is quoted per part.

Polarization locked output – the VCT-F85A32-SPL holds one polarization up to 8 mA with no flipping, which matters when the beam passes a grating or a polarization sensitive optic in a sensing path.

Datacom VCSEL rated by data rate – the VCT-F85A54-10M is specified to 10.3125 Gbps with 0.8 mA of threshold current at 25 C and 1.85 mA at 85 C, so the bias current has to track the case temperature across the range.

Bare die and packaged part from one wafer – the SPL DS90A_3 is the same 905 nm nanostack as a 600 by 400 um chip for a module that places the die itself, while the PL90_3 is that emitter in a radial can for a board level assembly.

Applications

These emitters are quoted for boards that have to launch light, typically where:

Optical modules and active cables – an 850 nm VCSEL at 10.3125 Gbps drives a multimode link to 300 m, with the monitor PD closing the power loop inside the module housing.

LiDAR, range finders and traffic sensors – a 905 nm nanostack at 75 W to 120 W peak gives the short pulse a time of flight channel needs, and the 1 ns rise time sets the distance resolution.

Sensing, projection and curing – an 850 nm single mode VCSEL gives a clean Gaussian beam for a laser mouse or a safety sensor, and the 447 nm blue part is used in projection and in curing rigs.

The emitter is placed on the same board as its driver and its monitor circuit, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Sourcing and Cross-Reference

Emitter selection is a chain of four checks. The first is the optical requirement: wavelength, power at the fibre or at the target, and the beam shape the optic expects. The second is the drive condition, because peak power, threshold current and slope efficiency are all quoted at one pulse width, one duty cycle and one case temperature, and a part run outside those conditions delivers a different number. The third is the heat path, since a 160 K/W plastic can and an 8 K/W metal can walk in wavelength at very different rates. The fourth is the safety class of the finished product, because a 905 nm part at 75 W peak is a Class 1 product only after the housing and the interlock are in place.

Second sourcing an emitter is stricter than second sourcing a logic part. Two parts with the same wavelength and package can differ in threshold current, slope efficiency and far field, so a replacement is confirmed against the data sheet curves and, for a module, against the coupling into the fibre. Where a maker flags a part as discontinued, as ams OSRAM has done for the 447 nm TO-90 device and for the PL90_3 radial can, the last time buy quantity is set from the production plan rather than from the stock on hand.

Where the emitter is a 1310 nm or 1550 nm DFB, the part usually arrives as a TOSA with the lens and the isolator already aligned, and it is quoted against the module platform, the reach and the data rate. The route for these parts is on our obsolete part cross reference hub, and the incoming check that keeps a re marked emitter out of a build is on verify original components.

For volume builds, SUPERB Assembly support covers the die attach and wire bond route for a bare chip, the TO can handling and the optical alignment step the module needs.

Q: Can you supply a discontinued 905 nm pulsed laser diode or an 850 nm VCSEL against the full ordering code?

A: Yes. Send the ordering code, the wavelength, the pulse condition or data rate and the quantity, and the SUPERB Tech team will confirm what the maker still ships and quote the part with the matching figures.

Why Buyers Source Emitters Through SUPERB

  1. Power figures read at the right condition: peak power is quoted with its pulse width, duty cycle and case temperature, so the part is compared on the condition the board actually runs at.
  2. Discontinued emitters handled as a last time buy: where a maker has ended a can or a die, the remaining quantity is reserved against the production plan instead of being bought from an open market lot.
  3. Package and heat path quoted together: the thermal resistance, the can material and the operating range are given with the part, because the wavelength shift over temperature follows from them.
  4. Emitter matched to the detector: the 850 nm and 905 nm parts are quoted alongside the PIN and avalanche photodiodes that receive them, so the pair is checked for wavelength and bandwidth.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Discrete and power semiconductors, Laser driver chips for optical modules, PIN and avalanche photodiodes, LED indicators and optocouplers, Verify original components, Component lead time solutions.