Contact Us
  • Home
  • COMPONENTS
  • I2C and SPI EEPROM ICs for Configuration and Calibration Data

I2C and SPI EEPROM ICs for Configuration and Calibration Data

I2C and SPI serial EEPROM from 2 Kbit to 1 Mbit in 8 lead packages. Supply from 1.7 V, which covers a coin cell and a 1.8 V rail without a regulator. One million write cycles and 100 to 200 years of data retention. Page sizes from 8 to 256 bytes, with hardware and block write protection.
quote now

Product Specifications

Product Overview

An EEPROM in a product holds the data that has to survive a power cut and a firmware update: the serial number, the calibration coefficients, the MAC address and the board revision. It is chosen on four numbers, the density, the bus, the minimum supply and the page size, and the page size is the one that is usually ignored. A 2 Kbit part with an 8 byte page takes eight write cycles to store a 64 byte calibration record, while a 256 Kbit part stores the same record in one, which matters when the write happens on every power down.

The I2C group covers the range from 2 Kbit to 1 Mbit. The AT24C02C and the AT24C256C run from 1.7 V to 5.5 V, reach 1 MHz in fast mode plus above 2.5 V, hold 1,000,000 write cycles and 100 years of retention, and take 5 ms for a self timed write. The 24LC256 is the 2.5 V version with a 400 kHz bus and a 64 byte page, the 24FC256 is the 1.7 V, 1 MHz version of the same die, and the 24AA256 is the 1.7 V, 400 kHz version, so a family can be moved between rails without changing the footprint.

The SPI group is for firmware images, boot records and log data. The 25LC256 and the 25AA256 are 256 Kbit parts with a 64 byte page, a 10 MHz clock above 4.5 V, 5 ms write cycles and block protection of a quarter, a half or the whole array; the 25AA256 extends the supply down to 1.8 V. The AT25256B runs to 20 MHz, which halves the time to rewrite a 32 Kbit image, and the M24M01 takes the I2C bus to 1 Mbit with a 256 byte page, which is the part used where a single record has to be written without a page boundary interrupt.

Key Specifications

ParameterI2C EEPROMSPI EEPROM
Density2 Kbit to 1 Mbit256 Kbit
Supply range1.7 V to 5.5 V on the AA, C and FC suffixes1.8 V to 5.5 V on the AA parts, 2.5 V on the LC
Bus speed100 kHz, 400 kHz and 1 MHz depending on part and rail10 MHz above 4.5 V, 20 MHz on the AT25256B
Page size8, 64 or 256 bytes64 bytes
Write cycle5 ms self timed5 ms self timed
Endurance1,000,000 write cycles1,000,000 write cycles
Retention100 to 200 years100 to 200 years
ProtectionWrite protect pin, software protectionBlock protect of a quarter, a half or all

Included Models and Order Codes

The table lists the order codes most often quoted for calibration records, identity data and small firmware images. State the density, the bus, the supply rail, the page size and whether the part has to be written on every power down, and the part and its packing are confirmed.

Part NumberDensityBusSupplyPage SizePackage
AT24C02C-SSHM-T2 KbitI2C1.7 V to 5.5 V8 bytesSOIC-8
AT24C256C-SSHL-T256 KbitI2C, 1 MHz above 2.5 V1.7 V to 5.5 V64 bytesSOIC-8
AT24C512C-SSHM-T512 KbitI2C, 1 MHz above 2.5 V1.7 V to 5.5 V128 bytesSOIC-8
24LC256-I/SN256 KbitI2C, 400 kHz2.5 V to 5.5 V64 bytesSOIC-8
24FC256-I/SN256 KbitI2C, 1 MHz above 2.5 V1.7 V to 5.5 V64 bytesSOIC-8
24AA256-I/SN256 KbitI2C, 400 kHz1.7 V to 5.5 V64 bytesSOIC-8
25LC256-I/SN256 KbitSPI, 10 MHz above 4.5 V2.5 V to 5.5 V64 bytesSOIC-8
25AA256-I/SN256 KbitSPI, 10 MHz above 4.5 V1.8 V to 5.5 V64 bytesSOIC-8
AT25256B-SSPDGV-T256 KbitSPI, 20 MHz2.5 V to 5.5 V64 bytesSOIC-8
M24M01-DFMN6TP1 MbitI2C, 1 MHz1.8 V to 5.5 V256 bytesSO8N

Key Features

Low voltage operation – 1.7 V parts run from a coin cell or a 1.8 V rail without a regulator, which is what a battery powered logger needs at end of life.

Page size that fits the record – a 256 byte page on the M24M01 stores a whole calibration block in one write cycle instead of four.

Write endurance – 1,000,000 cycles covers a product that rewrites its settings daily for decades, and it is quoted per byte page rather than per device.

Hardware write protection – a WP pin or a block protect register stops a runaway firmware from erasing the identity data, which is the failure that makes a board unbootable.

Pin compatible families – the same 8 lead footprint covers 2 Kbit to 512 Kbit and 1.8 V to 5.5 V, so a product can change density without a layout change.

Retention – 100 to 200 years at 55 C is what a calibration record needs when the instrument is expected to be recalibrated once a decade.

Applications

These parts are quoted for boards that have to remember something across a power cycle, typically where: A controller board is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same assembly, so the EEPROM, the programming step and the test record are handled together.

Instrument calibration records – coefficients, gain and offset tables and the calibration date sit in one page, so a service technician can read and rewrite them over the same I2C bus the sensor uses.

Network identity – a MAC address, a serial number and a hardware revision are written once at test and protected by the WP pin afterwards.

Firmware and boot records – a 256 Kbit SPI part holds a boot loader or a parameter set, and a 20 MHz clock halves the time to rewrite it during a field update.

Sourcing and Cross-Reference

EEPROM is treated as a commodity until a line stops because the part on the AVL is not the part in the drawing. The traps are the supply suffix, the page size, the write protect polarity and the package, and all four are in the order code rather than in the family name. We quote the full order code with the suffix and the date code, so the part that arrives matches the one the firmware was written for.

The other half is the bus. A 1 MHz part on a bus with 10 kohm pull ups will run at 400 kHz, and a page write that crosses a boundary will wrap and overwrite the start of the page, which is a software bug that looks like a failing device. We quote the part with the pull up value and the decoupling, and where a board is built in volume the programming step is agreed so the identity data is written once and verified.

Where the boards are built in volume, SUPERB Assembly support covers the placement and the programming of the EEPROM with a read back check before the board leaves the line.

Q: Can you supply a 1.7 V EEPROM that replaces a 2.5 V part on the same footprint?

A: Yes. Send the density, the bus, the supply rail, the page size and the order code suffix, and the SUPERB Tech sales team will confirm the replacement, the packing and the date code.

Why Buyers Source EEPROM Through SUPERB

  1. Full order code on the quote: density, bus, supply suffix, page size and package are stated per line, so the part matches the firmware rather than the family name.
  2. Programming and read back: identity data is written and verified on the line, which removes the field failure that comes from an unprogrammed part.
  3. Lifecycle supply: parts that a product was qualified around are held with date codes, and the pin compatible family gives a route when a density is discontinued.
  4. Low voltage options: the 1.7 V and 1.8 V suffixes are quoted beside the 2.5 V parts, so a battery product can be moved without a layout change.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Multi-function ICs, Logic level shifters and IO expanders, RS-485 and RS-232 transceivers, MCU and embedded processors, Pin to pin cross reference.