Contact Us
  • Home
  • COMPONENTS
  • Aluminum Electrolytic and Tantalum Capacitors for Bulk Hold Up

Aluminum Electrolytic and Tantalum Capacitors for Bulk Hold Up

Radial and SMD aluminum electrolytics from 220 uF to 1000 uF at 35 V and 50 V. Molded tantalum capacitors from 1 uF to 100 uF, in A, B, C and D cases at 10 V to 35 V. Impedance, ripple current, ESR and case size are listed per part number. Both families are quoted with the derating the maker data sheet asks for.
quote now

Product Specifications

Product Overview

These two families do the same job on different scales. An aluminum electrolytic holds the bulk charge on a rail after a rectifier, where the capacitance is hundreds of microfarads and the ripple current is amps. A tantalum holds a smaller charge close to a load, where the capacitance is a few microfarads, the ESR has to stay low at high frequency, and the part has to survive a reflow oven. Both are polarised, both lose capacitance in the cold, and both fail in a way that has to be planned around.

The aluminum part is chosen on ripple current and life, not on capacitance alone. A 1000 uF 50 V radial in a 12.5 by 40 mm case carries 2.92 A at 100 kHz and 105 C and lasts 10000 hours at that temperature, while the same capacitance in a smaller can carries less and runs hotter. Every 10 C below the rated temperature roughly doubles the life, which is why the can size and the ripple figure are quoted together with the capacitance.

The tantalum part is chosen on ESR and on voltage derating. A molded tantalum has a stable capacitance and a low ESR at high frequency, but it needs to be run at half its rated voltage or less on a low impedance rail, because a tantalum that sees a surge above its rating fails short rather than drying out. The table lists ESR and case size with each part, since the case is what sets both.

Key Specifications

ParameterAluminum electrolytic, radialAluminum electrolytic, SMDMolded tantalum, SMD
Capacitance range220 uF to 1000 uF in this list220 uF in this list1 uF to 100 uF in this list
Voltage range35 V to 50 V35 V10 V to 35 V
Impedance or ESR21 mΩ at 100 kHz180 mΩ at 100 kHz0.7 Ω to 10 Ω at 100 kHz
Ripple current2.19 A at 120 Hz, 2.92 A at 100 kHz300 mA at 120 Hz, 600 mA at 100 kHzset by the ESR and the case
Life10000 hours at 105 C2000 hours at 105 C2000 hours at 125 C
Temperature range-40 C to +105 C-55 C to +105 C-55 C to +125 C
Toleranceplus or minus 20 %plus or minus 20 %plus or minus 10 %
Voltage deratingnone needed inside the ratingnone needed inside the ratinghalf rated voltage on a low impedance rail

Included Models and Order Codes

The table lists the parts we quote most often. Capacitance, voltage, case size, impedance or ESR and ripple current are copied from the maker data sheet for each part number. Where a ripple figure is given at two frequencies, both are listed because the 120 Hz figure is the one a rectifier sees and the 100 kHz figure is the one a switching rail sees.

Part NumberTypeCapacitanceVoltageESR or ImpedanceCase
UHE1H102MHDAluminum, radial1000 uF50 V21 mΩ at 100 kHz12.5 x 40 mm, 5 mm pitch
UCD1V221MCL6GSAluminum, SMD220 uF35 V180 mΩ at 100 kHz10 x 7.7 mm, AEC-Q200
T491A105K016ATTantalum, molded1 uF16 V10 ΩA case, 3.2 x 1.6 mm
T491A106K016ATTantalum, molded10 uF16 V3 ΩA case, 3.2 x 1.6 mm
T491B106K016ATTantalum, molded10 uF16 V2.8 ΩB case, 3.5 x 2.8 mm
T491C106K025ATTantalum, molded10 uF25 V1.5 ΩC case, 6 x 3.2 mm
T491D106K035ATTantalum, molded10 uF35 V1 ΩD case, 7.3 x 4.3 mm
T491D107K016ATTantalum, molded100 uF16 V0.7 ΩD case, 7.3 x 4.3 mm
TAJC106K016RNJTantalum, molded10 uF16 V2 ΩC case, 6 x 3.2 mm
TAJA106K010RTantalum, molded10 uF10 V3 ΩA case, 3.2 x 1.6 mm

Key Features

Ripple current is the real rating – the 1000 uF 50 V radial carries 2.92 A at 100 kHz, and a rail that draws more than that heats the can past its rating no matter how much capacitance is on the label.

Life counted from the hot spot – 10000 hours at 105 C on the radial part, and roughly double that for every 10 C below the rated temperature, which is why the can size appears in the quotation.

Low impedance at high frequency – 21 mΩ on the radial part and 180 mΩ on the SMD part at 100 kHz are the figures that decide how much the rail sags on a switching edge.

Tantalum ESR by case – the same 10 uF 16 V part measures 3 Ω in an A case and 2.8 Ω in a B case, so the case size is a electrical choice as well as a mechanical one.

Voltage derating for tantalum – a molded tantalum on a low impedance rail is run at half its rated voltage, because a surge above the rating turns the part into a short rather than a drying can.

Temperature range to 125 C – the molded tantalum parts are rated to +125 C, which is where a board inside a sealed enclosure ends up and where an aluminum part has to be derated.

Applications

These capacitors are quoted where a rail needs bulk charge or a load needs a low impedance source, typically where: These capacitors are placed on the same rail as the regulator and the load, so they are quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Rectifier output on a power supply – a 1000 uF 50 V radial holds the rail between the rectifier peaks and carries the ripple current, with the can size set by the ripple figure rather than by the capacitance.

Point of load decoupling – a 10 uF molded tantalum in a B or C case sits next to a regulator output or an amplifier supply pin, where its low ESR at high frequency damps the rail.

Industrial board in a hot enclosure – the 125 C tantalum rating covers a board that runs hot inside a sealed box, where an aluminum part would need a larger can and a shorter life.

Sourcing and Cross-Reference

These two families are not interchangeable, and the quotation starts from the rail. On a rectified rail the aluminum part is sized on ripple current, can diameter and the temperature at the can, and the capacitance comes out of the hold up time. On a low impedance rail the tantalum is sized on ESR and derating, because the same capacitance in a smaller case has a higher ESR and a shorter surge margin.

Mechanical limits decide the rest. A 12.5 by 40 mm radial needs height on the board and a keep out for the vent, an SMD aluminum needs the pad size the maker specifies for the can, and a molded tantalum has to be placed away from a connector where a hot plug surge can reach it. Polarity is marked on all three, and a reversed aluminum part vents within minutes.

Where a series has been discontinued, the replacement is checked on capacitance, voltage, ESR, case size and the ripple the rail draws. The route for these parts is on our power management cross reference page, and the shortage path for a rail that is already in production is on BOM shortage recovery.

For volume builds, SUPERB Assembly support covers the polarity check, the pad size for the can, the reflow profile for a molded tantalum and the keep out around a vented radial part.

Q: Can you supply a tantalum with the same case and ESR as a part that is no longer available?

A: Yes. Send the capacitance, the rail voltage, the ESR or impedance limit, the case size and the ripple current, and the SUPERB Tech team will confirm which part fits and quote it with the derating the rail needs.

Why Buyers Source Bulk Capacitance Through SUPERB

  1. Sized on ripple, not on the label: the ripple current and the can size are checked against the rail, so a part is not bought on capacitance alone and then run past its rating.
  2. ESR quoted by case: the same value in two case sizes has two different ESR figures, and the one that matches the rail is the one quoted.
  3. Derating applied per family: tantalum parts are quoted at half rated voltage on a low impedance rail, which is the difference between a long life and a short circuit.
  4. Height and pad checked: can height, vent clearance and pad size are checked against the board before a part is offered as a replacement.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Passive components, MLCC and ceramic capacitors, Supercapacitors and backup energy cells, BOM shortage recovery.