Contact Us
  • Home
  • COMPONENTS
  • VCXO and OCXO Modules for Timing and Synchronization

VCXO and OCXO Modules for Timing and Synchronization

Voltage controlled oscillators from 1 MHz to 220 MHz with pull range from ±25 ppm to ±1600 ppm. Oven controlled parts hold ±10 ppb to ±200 ppb, with warm up inside 3 minutes and 1 W steady state. Phase jitter is 0.225 ps RMS on the differential VCXO and -145 dBc/Hz at 1 kHz on the 10 MHz OCXO. Each row lists the output type, the supply and the package, because those three decide the layout.
quote now

Product Specifications

Product Overview

A VCXO and an OCXO solve the same problem from opposite ends. The VCXO is a plain crystal oscillator with a varactor in the circuit, so a control voltage on one pin pulls the output a few tens or a few thousand ppm, which is enough to lock it to an incoming reference. The OCXO puts the crystal in a heated oven held a few degrees above the highest ambient the part will see, so the crystal never changes temperature and the output stays within a few parts per billion of nominal without any reference at all.

That is the trade. A VCXO locks quickly, draws 10 mA to 80 mA and costs a fraction of an oven part, but its absolute accuracy is still that of a crystal, so it can only be as good as the reference driving its control pin. An OCXO is a frequency standard on its own, holds ±10 ppb over -40 C to +85 C and keeps that accuracy through a supply loss, but it draws 1 W, needs a few minutes to warm up and takes a 22 x 25 mm footprint with a metal can.

Pull range is where most part numbers are lost. A VCXO quoted at ±50 ppm pull is not the same as one quoted at ±50 ppm APR: the absolute pull range subtracts the stability, the aging and the supply tolerance from the pull, so a ±50 ppm pull part with ±25 ppm stability leaves ±25 ppm APR. SiTime states this directly in its APR table, and Epson quotes the same part at ±65 ppm APR on one grade and ±80 ppm on another, which is the difference between locking a 20 ppm reference and locking a 100 ppm one.

The table below covers the two families we quote most often: quartz VCXO in 7.0 x 5.0 mm and 3.2 x 2.5 mm, programmable differential VCXO for line card clocks, and oven parts in a 20.8 x 13.2 mm leaded can and a 22 x 25 mm surface mount package. Where a family is offered in both fixed and voltage controlled form, both order codes are listed, because the control pin changes the loop filter on the board.

Key Specifications

ParameterQuartz VCXO, CMOSDifferential VCXO, programmableOCXO, oven controlled
Output frequency1 MHz to 170 MHz1 MHz to 220 MHz5 MHz to 50 MHz
Pull range±65 ppm to ±140 ppm APR±25 ppm to ±3200 ppm±5 ppm trim on voltage controlled types
Stability over temperature±30 ppm to ±50 ppm±15 ppm to ±50 ppm±5 ppb to ±500 ppb
Output typeCMOSLVPECL, LVDS, HCSLCMOS or sine, 2 dBm into 50 Ω
Supply1.8 V, 2.8 V, 3.3 V, 5.0 V2.25 V to 3.63 V3.3 V or 5.0 V
Current10 mA to 20 mA73 mA to 92 mA1.0 W steady state, 2.0 W at turn on
Phase performance-145 dBc/Hz at 1 kHz on a low noise quartz part0.225 ps RMS, 12 kHz to 20 MHz-145 dBc/Hz at 1 kHz on a 10 MHz carrier
Warm up3 ms to 10 ms3 ms±500 ppb inside 3 minutes
Aging±3 ppm first year±1 ppm first year±500 ppb per year, ±3 ppm over 10 years
Package3.2 x 2.5 mm to 7.0 x 5.0 mm3.2 x 2.5 mm to 7.0 x 5.0 mm20.8 x 13.2 x 8.2 mm, 22 x 25 x 12.7 mm

Included Models and Order Codes

The table lists the order codes we quote most often. Frequency, stability, pull range, supply and package come from the maker data sheet for that code. Where two codes share a family, they differ only in the option suffix that sets stability, temperature range or output waveform, so the suffix is part of the number and is never dropped.

Part NumberTypeFrequencyStabilityPull RangeOutputSupplyPackage
VG-4231CA 25.0000M-FGRC3VCXO25 MHz±50 ppm±65 ppm APRCMOS3.3 V7.0 x 5.0 mm
VG-4231CA 37.7210M-TGRHVCXO37.721 MHz±50 ppm±80 ppm APRCMOS5.0 V7.0 x 5.0 mm
VG-4231CE 25.0000MVCXO25 MHz±30 ppm±140 ppm APR at 3.3 V controlCMOS3.3 V, 2.8 V or 1.8 V3.2 x 2.5 x 1.05 mm
VG7050CDN 156.2500MVCXO156.25 MHz±50 ppm±50 ppm APRCMOS3.3 V7.0 x 5.0 x 1.5 mm
VG5032EFN 156.2500MVCXO156.25 MHz±50 ppm±50 ppm APRLV-PECL3.3 V5.0 x 3.2 x 1.3 mm
SiT3372AI-1E9-33NZ156.250000VCXO156.25 MHz±35 ppm±1600 ppm PRLVPECL3.3 V7.0 x 5.0 mm
AOCJY1-10.000MHZ-EOCXO10 MHz±200 ppb over -20 to +70 C±5 ppm trimCMOS3.3 V20.8 x 13.2 x 8.2 mm
AOCJY1-10.000MHZ-E-SWOCXO10 MHz±200 ppb over -20 to +70 C±5 ppm trimSine, 2 dBm3.3 V20.8 x 13.2 x 8.2 mm
OH300-61003CF-024.576MOCXO24.576 MHz±10 ppb over -40 to +85 Cfixed frequencyCMOS3.3 V22 x 25 x 12.7 mm
OH100-61003CF-010.0MOCXO10 MHz±10 ppb over -40 to +85 Cfixed frequencyCMOS3.3 V1.0 x 1.0 x 0.5 in
OH300-52005CV-010.0MVCOCXO10 MHz±20 ppb over 0 to +70 C5 ppm or lessCMOS5.0 V22 x 25 x 12.7 mm

Key Features

Pull range and APR are not the same figure – a quartz part quoted at ±50 ppm pull with ±25 ppm stability and ±3 ppm per year aging leaves about ±22 ppm of usable absolute pull, which is the number that decides whether it locks to a 20 ppm reference.

Oven parts hold accuracy without a reference – ±10 ppb over -40 C to +85 C means the part is a frequency standard on its own, so a base station, a test instrument or a Synchronous Ethernet port keeps its frequency through a loss of the upstream reference.

Warm up inside three minutes – the AOCJY1 reaches ±500 ppb of final frequency in under 3 minutes at 25 C, and the OH300 series reaches 0.10 ppm in about 5 minutes, so the hold over window starts early in a boot sequence.

Phase noise stated at a real offset – -145 dBc/Hz at 1 kHz on a 10 MHz carrier and 0.225 ps RMS integrated from 12 kHz to 20 MHz are the two figures that decide whether a part suits a converter clock or a SerDes reference, and both are quoted per part.

Voltage control on the same footprint – the AOCJY1 and the OH300 series are offered as fixed frequency OCXO and as VCOCXO in the same package, so a loop that needs trimming later does not need a new footprint.

Supply and output fixed at order – a VG-4231CE is ordered at 3.3 V, 2.8 V or 1.8 V with the matching control voltage swing, and the pull range changes with that choice, so the supply is part of the order code and not a strap on the board.

Applications

These parts are quoted for boards that have to generate or lock a clock, typically where:

Telecom line cards and Synchronous Ethernet – a 156.25 MHz differential VCXO locks to the recovered line clock inside a few ppm, and an OCXO holds the port frequency while the reference is lost, which is what the holdover requirement asks for.

Test and measurement instruments – a 10 MHz OCXO at ±10 ppb is the house standard that a counter, a signal generator or a spectrum analyser locks to, and the same board can carry a VCXO for the sample clock.

Base stations and microwave backhaul – an oven part at 24.576 MHz or 38.88 MHz feeds the radio frame clock, where a few ppb of drift over temperature shows up directly as a frequency error at the air interface.

The oscillator sits on the clock tree of the same board, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Sourcing and Cross-Reference

Selection starts with the reference, not with the oscillator. If the board receives a clock from the network or from a GPS module, a VCXO with enough APR to cover the reference error plus the aging over the service life is the cheaper route, and the loop filter is set from the pull slope and the control voltage range. If the board has to keep time with no reference at all, the oven part is the only option and the budget goes to warm up current and holdover accuracy instead of to pull range.

The second check is mechanical and thermal. An OCXO draws 1 W in steady state and 2 W at turn on, it wants a clear area around the can for the oven, and the 22 x 25 mm package needs a stiffener under it on a thin board. A 3.2 x 2.5 mm VCXO is the opposite case: it is placed next to the PHY and its supply needs its own decoupling and a clean ground, because the pull pin is sensitive to noise on the rail.

Where a family has been discontinued, the check is on the suffix, not on the family name. Two codes from the same series can differ in stability, temperature range and output waveform, so a replacement is confirmed against the full order code and the datasheet table rather than the base part number. The route for these parts is on our obsolete part cross reference hub, and the drop in check is on pin to pin cross reference.

For volume builds, SUPERB Assembly support covers the placement of the oven can with its keep out area, the pull pin filtering and the supply decoupling the part needs.

Q: Can you supply a 10 MHz OCXO or a 156.25 MHz VCXO against a full order code, including the option suffix?

A: Yes. Send the full order code with the option suffix, the frequency and the quantity, and the SUPERB Tech team will confirm the stability, the pull range and the package from the maker data sheet before quoting.

Why Buyers Source Timing Parts Through SUPERB

  1. Order code read in full: the suffix that sets stability, temperature range and output waveform is checked before quoting, so a part that looks the same in a search result is not sent in place of the one on the BOM.
  2. APR checked against the reference: pull range, stability and aging are added up to an absolute figure and compared with the reference error, which is the step that decides whether a VCXO locks at all.
  3. Oven parts quoted with their power budget: warm up current, steady state power and the keep out area around the can are given with the quotation, because those three decide whether the part fits the enclosure.
  4. Long life parts tracked as a family: where a series is offered in fixed and voltage controlled form, both codes are quoted so a later change does not force a new footprint or a new board revision.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Crystals and oscillators, Crystal units and TCXO oscillators, Real time clock ICs and timing buffers, PCIe clock generators and redrivers, Clock generators for optical line cards, Component lead time solutions.